Small and MIGHTY!! Gen 3 Milwaukee M12 FUEL Hammer Drill Driver and Impact Driver Review

Подписаться 164 тыс.

Просмотров 208 тыс.

50% 1

If you're looking to lighten your tool load, you need to check these out. These new Gen 3 M12 FUEL Hammer Drill and Impact Drivers deliver quite an impressive performance while still remaining very compact. Model 3404 is the Milwaukee M12 FUEL Hammer Drill Driver with 400 in-lbs or torque and 1,550 RPM max. The Model 3453 is the Milwaukee M12 FUEL 1/4" Hex Impact Driver with 4 power modes and 1,500 in-lbs of torque. That's 125 ft-lbs, and we verify this claim. You can get the 3404 for $149 (bare), and you can get the 3453 for $139 (bare). The best deal is to pick up the combo kit, model 3497-22, which includes the M12 FUEL Hammer Drill, Impact Driver, a XC 4.0 M12 battery, 2.0 M12 battery, and a charger for just $229. They are covered by a 5-year warranty.
Milwaukee 3404 Hammer Drill: imp.i284638.ne...
Milwaukee 3453 Impact Driver: imp.i284638.ne...
Milwaukee 3497 Combo Kit: imp.i284638.ne...
Gen4 M18 FUEL Hammer Drill Review: • Milwaukee 2904 Gen 4 M...
Gen4 M18 FUEL Impact Driver Review: • Milwaukee 2953 Gen 4 M...
Keep current with our great content:
Facebook: / shoptoolreviews
Twitter: / shoptoolreviews
Instagram: / shoptoolreviews
RU-vid: / shoptoolreviews

Опубликовано:

27 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 266

@enthused7591 2 года назад

I can not believe that little impact driver just took off 225 ft lbs with a half dead 2.0 battery and an adapter. The next M12 stubby impacts are going to absolutely rip. I could see them ripping off 550 ft lbs

@Shoptoolreviews 2 года назад

We can't wait to see that. Thanks for watching.

@ZeGermanHam 2 года назад

I'm patiently waiting for the next gen M12 stubby impact wrench, whenever it may come. It's sure to be a monster.

@bzd16b 2 года назад

I can not believe the 1/4" hex surviving the test!

@superspeeder 2 года назад

The current Stubbies are at the top of the heap and not that old, what makes you think they're due for replacement? My bet is they will be around for a while yet.

@flooid5506 Год назад

My snap on 1/2” 18V impact can’t do that. I’m serious

@Honoer 2 года назад

The 12v tool lineup has to be the most handy tools they make, especially for mechanics.

@greenrhinofarms2830 Год назад

I burnt up a whole set of Ryobi drills and impacts on a previous job. 5 tools in all On fire literally. Needed some tools to build a 10x12 shed and 2x8 pt platform for it. Grabbed the combo set you talked about at HD for $199, with a free High Output 2.5. I built the entire base on the 4.5, on the charge from the box. And then built the entire shed with the 2.0 and it’s charge from the box. I haven’t even touched the drill yet! At the end of the job, I got gifted a m18 surge 1/4 hex impact and new Xc 6.0 SMH 🎉 the Lord Provides! Got all that for $214! Haha God bless great video! I now know the true deal I got!

@omarjaramillo4435 Год назад

well well tell me you dont know how to use a tool without telling me you dont know how to use a tool. 🤣

@Swampytheroot Месяц назад

My batteries wouldn't even take a charge. Found out the charger has to be plugged in before inserting the batteries. Odd. I have 1990s Ryobis with 25+ year old batteries that still work every single day

@MsladyPearlz Год назад

Drill- Packedge in typical box, came with a tool bag (added bonus), two batteries, one charger, drill, and driver. Two words "plenty of Torque" ru-vid.comUgkxW1vOBRCMrgTCDEijzpVzDWsgI-Jm2iQv well I guess that's three. Nice upgrade from current setup. Has belt clips, I don't think I will be using those. Driver and drill were bigger than what I expected but it is an upgrade from the current setup. For the money I would say that this is a great setup for Professionals and DIY/Weekend warriors.

@jimmynguyen8277 27 дней назад

This is the video that made me go get this kit. I’m a new home owner DIYing things. It was this vs the m18 non fuel.

@TorqueTestChannel 2 года назад

Great vid Tim! Looks like you got about 550 from the M18 and 225-250 from the M12 here. We're also seeing the M12 make 1/2 of the M18, which surprised me at 1st

@Shoptoolreviews 2 года назад

Thanks for the info! That's good to know. For a 2-lb tool, it's crazy what these things are delivering.

@TorqueTestChannel 2 года назад

@@Shoptoolreviews thats a good point

@Dirtyharry70585 Год назад

@@TorqueTestChannel yah not looking for the maximum uga-duggas, looking for size to fit job use

@ARluvr1 2 года назад

Man these are good looking tools. Just ordered my kit, can’t wait for it to come in. The gen 2 impact has been used everyday since it came out and hasn’t let me down.

@dangrimes5078 2 года назад

I have the gen 2 kit also. Would you happen to know what the difference is with the gen 3? I can't believe he didn't mention that unless I missed it. I just don't see any difference.

@thecarproconnoisseur5412 2 года назад

Got mine yesterday.. I work at Home Depot, I grabbed it as soon as it came off the truck.. wasn’t even put out for sale… and it was the only m12 combo kit that came in 😂🤣😂.. we got a bunch of the new m18s tho

@DanielGomez-cf6vk 2 года назад

I’m still happy with my gen 2 might get it with a promotion later on no rush

@drew5992 2 года назад

Me too. Maybe Black Friday. Lol

@Shoptoolreviews 2 года назад

Some people are saying there's a hack deal to get these in the deal of the day. You may want to do some research.

@DanielGomez-cf6vk 2 года назад

@@Shoptoolreviews it’s the gen 2 version that are hackable not gen 3

@KnKn-rr9ri 2 года назад

I picked up the gen 2 combo last week for 130 from HD. Should I return it and pick up the gen 3? Is it worth the $100 for the new gen?

@MarcM143 2 года назад

@@KnKn-rr9ri I don't think so, I've seen the comparison on drilling in different fasteners and the Gen 2 performance seems to be right there with the Gen 3

@ZeGermanHam 2 года назад

I just bought the combo kit for $229, and Milwaukee is running a deal right now there they throw in an *additional* CP2.0 battery. So for $229, you get the 3404 hammer drill, 3453 impact driver, *two* CP2.0 batteries, one XC4.0 battery, a charger, and a case. Pretty incredible value. I can sell my lightly used Gen 2 stuff and get into these Gen 3 tools for very little money.

@JesusPerez-yc6yu 2 года назад

If u do the 229 deal with the 2.0 battery u can get a refund on the 2.0 and get 50 back. So the kit cost 180 essentially

@brianbaum2466 Год назад

Would’ve liked to see the drill/driver drilling some metal. I’m an electrician and drill a lot of steel cabinets for knock out punches (7/8 holes for example) or use a step bit on cabinets. My old gen 2 m12 drill struggled with those tasks big time, I’d like to see how this would fare in a similar task before I purchased

@chonch12414 Год назад

@@JesusPerez-yc6yu how do you get a refund on the 2.0? I just got the kit for $199 from Home depot with the 3 batteries

@JesusPerez-yc6yu Год назад

@@chonch12414 just go to customer service (returns) and say u want a refund on the let's say 2.0. On the receipt it tells u the refund amount.

@chonch12414 Год назад

@@JesusPerez-yc6yu makes sense. They actually threw in a HO 2.5 battery. But might he worth getting refund to go towards another XC

@DiligentDave1966 Год назад

I’ve seen this drill perform better in other videos using an xc6.0 battery. It’s actually a pretty impressive set, plus you can get a free battery. It’s also nice that it has a 1/2” chuck. I actually also like the grip, even though it’s a little fat. The gen 4 m18 grip feels long and skinny to me.

@FlyinTrapezious 2 года назад

Great review Tim! I bought the m12 Gen 3 and it is more powerful than Gen 2. I also bought the m18 Gen4 and ended up returning it was garbage compared to my Gen 3. The battery deal was great with the Gen 4 but does not have the guts of Gen 3.

@clone1137 2 года назад

It’s insane what these 12v tools will do. This is my favorite channel to watch tool reviews. And I’ve been waiting (what feels like) forever to see more about the new M12 impact and drill. Considering the power tools like this, and the M12 stubby can make, do you guys think we will ever see a 12 V mid torque?

@procrastinator1842 2 года назад

I've also been waiting forever for this. It's unfortunate that he wasn't able to use the new M12 high output 5.0 battery. According to Milwaukee it increases power by 25% which probably would have made that 1" auger go through without an issue. Stay tuned. I was looking at jumping to M18 because I need the extra grunt from the 1/2" drill, but now I should be able to stay all M12.

@DarthCuda Год назад

He also was not drilling properly by going straight into the wood.

@alexisschecter6554 Год назад

Considering this is pressure treated wood, that switchblade did a pretty good job. It looks like I'm going to have to add Milwaukee's 12 volt lineup to my Milwaukee platform As usual another Awesome Video!!

@hammerheartdan6311 2 года назад

Since the new M12 impact driver is even more OP, i took upon myself to rename the 4 speeds; Speed 1: eco-mode Speed 2: normal/work mode Speed 3: sport mode Screw mode: 2-step/launch control.

@hammerheartdan6311 2 года назад

@@Joey-yq5se LOL no, it’s based off the electronic throttle modes on mine and my buddy’s can am outlanders, which does the same thing essentially, (eco mode: smooth, slow power delivery, work mode: less abrupt clutch engagement, and finally sport mode: full gusto, shit your pants power with many accidental wheelies) lol

@InCountry6970 Год назад

One of the best reviews of this tool combo. Thanks

@justuntheranderson3141 2 года назад

The impact is huge power in a itty bitty packing! And the tri-light is bright as heck you can definitely see the difference. I just got my impact Tuesday and been using the crap out of it! I can’t wait to pair it with the New HO m12 battery they came out with! I just got the gen 2 m12 hammer drill and from what I can see there wasn’t that big of a difference over all! So I won’t up grade that it’s basically brand new still! But that impact was amazing

@legros731 Год назад

I would say the mode ring is way better that the gen 2 the impact mode are more spaced apart from the drill mode and you don't accidentally put the drill on the 12 mode really annoying apart from this they upgraded the led ligth to be more like thevrest of the true view color and the chuck is a little better but nothing to really brag about

@holyghost5981 Год назад

I went from working on cars for BMW to a general contractor. I love both jobs. The funny part is that I went from snap-on to Milwaukee. The price difference definitely help my wallet.

@creepyunclephil 11 месяцев назад

And how's the difference in quality? I'm a general contractor who also works on cars all the time. I have a small fleet of f150s of various ages that I work on myself. (I am actually rebuilding suspension in one this weekend and will start building a new tranny for another over the next week) I never owned snap ons and they'd always seemed ridiculously priced to me. I use dewalt 20v tools for all of my construction tools and we're talking about a lot of tools. Love them, wouldn't get anything else. I also have the big 20v impact wrench from dewalt for lug nuts and such. Then I have some 12v Makita specialty construction tools. The quality of those japanese tools is very high and they have an interesting selection. Now lastly, I have a huge selection of m12s for all of my automotive needs + plumbing tools (the m12 copper tube cutter and stapler are the best things since sliced bread). Now as to Milwaukee m18, I really just find it a little but overpriced and would recommend the DeWalts to anyone. But for the 12v stuff, Milwaukee definitely beats the competition!

@creepyunclephil 11 месяцев назад

Also Harbor Freight ICON tools and some older Pittsburghh Pro are my choice for sockets, hand ratchets and stuff. My oldest set of HF sockets (a 3 decker set with a couple hundred pieces) has lasted me a decade at this point and only a handful of sockets broke. So definitely don't be afraid of Harbor Freight, especially when it comes of their newer stuff. It's surprisingly high quality.

@holyghost5981 11 месяцев назад

@@creepyunclephil I haven't had a problem with snap-on. I was a Mechanic for 14 years. The price difference was a big difference i went from 46,000 in snap on down to 12,000 on milwaukee, Ridgid, makita and dewalt tools. My wife was happy that I don't spend that much in tools. The only good part about snap on most of the tools that I had I sold for near the same price the I paid for it. I think I'm addicted to pack out because if you saw my Garage you would say the same thing.

@timweb1510 7 месяцев назад

@@creepyunclephilicon sockets low quality for the price

@enthused7591 2 года назад

Just got a steal on the gen 2 Fuel kit. These tools are unreal for their size.

@Shoptoolreviews 2 года назад

Nothing wrong with the Gen 2 stuff either. Great find.

@geoffstrickler 2 года назад

The 2nd gen version of these are fantastic, these look to be minor upgrades, probably not worth upgrading from 2nd gen, but for anything older or a new buyer, highly recommended. Also, I don’t understand the people who complain about the handle size. I have smaller hands (wear a “large” glove, but can fit in a medium, a bit snugly), and I have no issue with the M12 handles. For people who wear a “small” glove, I suppose it could possibly be an issue.

@Shoptoolreviews 2 года назад

Very good points. You are correct, I wouldn't buy the Gen 3 if I was on the Gen 2 platform, other than the impact driver light. Handle bulge and size doesn't bother us either, but it is worth mentioning. Thanks for watching.

@user-nh3gu1ge3d Год назад

I agree. I would say my hands are small but the tool feels perfect to me. Maybe it's the 5'0 dwarfs having an issue with the size? I'm "only" 5'9 and the tools feel pretty tiny to me...

@ndoc8889 2 года назад

These tools really love the 6.0. There’s a palpable difference even between the 4.0 and 6.0 with both tools. Really interested in any possible gains from the HO 5.0 and 2.0s.

@procrastinator1842 2 года назад

The 6.0 XC uses a 2 banks of Samsung 30Q cells. This gives it a continuous rating of 30A. The new HO most likely uses Samsung 25S cells, giving it a continuous rating of 50A. That should equate to a huge jumo in power for high demand tools, and a lot less cutting out of tools.

@rooster_saucer Год назад

@@procrastinator1842torquetestchannel did some messing around with these.. not much of a difference between the 6.0 and the HO batteries… came to the conclusion the tool itself is pretty much maxed out with the 6.0 so anything more doesn’t make a difference.

@procrastinator1842 Год назад

@s rooster It does make a big difference on things that draw a stall current. The 13mm hammer drill and sds hammer drill for instance. Big difference. Not so much for impact drivers which never see stall torque because the impact mechanism is basically a type of clutch.

@ryanchristopher2207 2 года назад

I have to be honest and I'm not a spokesperson for Milwaukee, in fact I don't own any Milwaukee power tools I think I have a couple of their hand tools like a jab saw that folds up and that might actually be it. But I feel like you kind of did a disservice to the drill when you were using the auger bit and maybe even a couple others by one handing it. I don't know if you were holding a camera which apparently I'm looking at it again now and you're not so I don't know why you were one handing it but because of the force of the drill the angle at which you were going into the wood and threw the wood kept changing in the process, which in my opinion definitely serves to see the drill bind up faster. I mean I feel like you can literally see your hand being Jarred from the torque being distributed to your hand as it's trying to drill through the wood which when your hand gets yanked the angle at which you're holding the drill changes dramatically dramatically increasing the chance of binding. Dramatically! Just my opinion probably or maybe it's physics. I don't know you'd have to ask a physicist or a tool expert.

@BlindMansRevenge2002 2 года назад

That is pretty darn impressive! Milwaukee is putting some crazy power into those 12 V tools. The thing is, daily in and out use and longevity can only be measured by time load in the regular affects of the work environment. I wonder if one of those things can make it past the warranty. Without being sent in.

@mt1885 2 года назад

Have had good luck with Dewalt brushless, ACDelco cordless brushless - they seem to do good long term.

@alpham777 Год назад

Just got the combo today on sale 199$ at Farm and Fleet. Also comes with a handy bag.

@Shoptoolreviews Год назад

That's a really good deal.

@brucemoriarty9964 2 года назад

I have both M12 & M18 . Love my M12's the same as my M18 's. Great video once again , and have a great night 👌

@Shoptoolreviews 2 года назад

Thanks very much. Appreciate the positive feedback.

@mhsvz6735 2 месяца назад

Great review, thank you. Very happy with my 3497-22 combination kit.

@shtzweak Год назад

I’d get the kit, but honestly after I got my impact driver I never reach for my hammer drill driver anymore, I may not be doing things right, but the impact always gets the job done for me

@paulpersons799 Год назад

Yep same here buddy, lol

@justauser 7 месяцев назад

12V tools have replaced my 18 volt ones. I have very little 18 volt tools left. I no longer need an 18V impact driver, these are amazing! The 2.5 HO is perfect for these too

@Saladon89 Год назад

Oh yea, awesome tools for DIY mechanic, also got the 3/8 stubby 2554-22 kit for the tough jobs, anything tougher i crack it loose with a breaker bar

@402SHO 2 года назад

Yessss I can’t wait to get these the drill is just a little bit to weak to mix a 3/4 full bucket of mud. So the extra in lbs might help

@Shoptoolreviews 2 года назад

Yeah, I don't think these M12 tools should be mixing any mud. Thanks for watching.

@402SHO 2 года назад

@@Shoptoolreviews Awh it does perfectly fine actually on speed 1 with a medium/small paddle. I’ve had them for about 2 1/2 years now still going strong. Only issues with Milwaukee have been my m18 HO 8.0 both went bad within a year.

@SouthFLTools Год назад

@@402SHOI’ve had problems with my HO 8.0 batteries as well. Milwaukee Customer Service has been great about replacing them though.

@NO_OPEC_NO_PROBLEM 8 месяцев назад

Looks like for the bigger tasks the 18V would work better with that drill. It busted through that cinder block… impressive. Impact driver is even more impressive could pull 250lbs nut, especially with a 1/2” upgrade. Bought this kit over X-Mas for $179 w/ add’l 2.5 battery. It’s been a massive upgrade over Ryobi.

@LUCASPELUCAS777 8 месяцев назад

I just got the same pack Today, I’m new to tools in general and I was kinda bummed out when I found out there was the M18 series after I purchased this but so far so good with all the reviews.

@NO_OPEC_NO_PROBLEM 8 месяцев назад

@@LUCASPELUCAS777 True, but for around the house my M12 is kicking ass. If I need to pull lug nuts I’ll have to get a M18 1/2” or 3/8”. I’d make sure you;re using the High Output batteries on that M12, they get a lot more power.

@LUCASPELUCAS777 8 месяцев назад

@@NO_OPEC_NO_PROBLEM Thanks man will do, I got myself the M18 brushless 2 pack for sale yesterday for only 189$ it’s not the fuel but I’m glad to have something more powerful just in case I need it. I can always get the m18 fuel later on. Thanks for the advice man 🤙

@keith7630 Год назад

Just bought the kit at HD for $199. It came with the 4ah and 2ah batteries, plus it included a 2.5ah bonus battery. Hella good deal.

@jesustrevino6936 Год назад

What deal was that because I only see the one that has the 4 ah and 2ah battery?

@Stanging84 Год назад

@@jesustrevino6936 check home Depot

@jordanseitzinger3167 2 года назад

Is it still an electronic clutch? That’s the one thing I can’t stand and just won’t use. Love the drill other than that

@brandynh1439 2 года назад

No electronic clutch. You can hear the mechanical clutch when Tim tried drill the 4th hole in speed 1. He then adjusted it so it wouldn’t slip.

@is5032 2 года назад

Fantastic review thanks Tim. I am after a compact combo set and am considering these or perhaps the Dewalt 805 drill and 850 impact driver with power stack combo. Very different tools but great to see such compact powerful tools

@ricksgiggle8852 2 года назад

I'd say grab the dewalt or maybe the dewalt dcf840 slimmer but slightly longer than the 850 but with more power unless you need a selector switch. The 805 hammer drill is perfect. Once you get used to the 18v then maybe consider this milwaukee 12v combo. Can't go wrong with it.

@joemilton1010 2 года назад

Get Milwaukee in a Labor Day deal at Home Depot rn

@jermainecoburn8654 Год назад

@@ricksgiggle8852y

@Atum_Ra 2 года назад

The Hammer drill seems perfectly suited for an installation driver, all you could need. With those large hole hog type bits im not sure why they dont just make a set to attach to a Milwaukee mid torque imoact wrench Seems like a impact would be ideal for drilling thise large hole to stop kickback. @ Shop Tool Reviews Maybe you could recommend to Milwaukee thry try making a set of Augers that attach to a 3/8 & 1/2 anvil I bet it works, I donit with my impact driver and hex spade bits all the time

@scottbionicnerf8727 Год назад

I'm sure what the spec's are on my 9yrold Ryobi P238 1/4Hex driver, but it's twice the size of the that little M12 Hex driver. That's crazy good power from such a small package.

@dougmcgill0365 6 месяцев назад

M12 platform is perfect for finish carpentry, I should have switched over from M18 years ago

@takenusername Год назад

I’m about to grab this drill bare tool with free 2.5 HO battery, and the Surge kit with 2 batteries and free 2.5 HO battery. I’ve decided it’s time to augment my HO battery supply.

@jesterraj Год назад

Just got this kit after wanting the impact over 3 yrs ....impact is loud thou but I like

@SouthFLTools Год назад

Great video! I’m in both the M12 and Ridgid 18v platforms. Since you tested both, what are your thoughts on the M12 Fuel Gen 3 vs the Ridgid subcompact Gen 2 tools? Overall, in your opinion, is the performance about the same, or do you give the edge to one compact line over the other? Thanks Tim!

@nannesoar Год назад

14:35 hahaha the vice was even caught off guard with this test 😂

@loktom4068 10 месяцев назад

Large holesaw drilling of 2 3/4 " and up size is the toughest testing for most drills. That included corded drills. This test will show who's the peewee, and whose the incredible HULK.

@TheKurtTribute Год назад

Granted everyone has different hands, but I’ve never understood the complaints about the grip size. I’m 5’6” and have no issue, obviously my hands are far from large given my height.

@BBerkow 2 года назад

What is the make / model of the electronic torque wrench you used during the torque test? That thing is awesome!

@zunrue1 Год назад

Try the high-output batteries for these reviews in the future, an HO 2.5 can outperform a standard 4.0

@loktom4068 10 месяцев назад

Who actually uses those side metal hanging clips?

@fuxbox 10 месяцев назад

I do probably 100 times a day

@fuxbox 10 месяцев назад

well to be fair, on the m18 line. this is my first m12 and havent actually used it yet lol

@franklong6269 7 месяцев назад

Spectacular review!

@TacticalThib Год назад

I just bought this kit for 150.00 bucks 2.0 4.0 5.0 drill and driver from the depot!!

@chrisx5127 Год назад

How?

@MrCaribe65 Год назад

@@chrisx5127 Home Depot deals pop up from time to time. Right now, this kit is 229.00 with a choice of an extra tool.

@harlanborders943 2 года назад

It seems that the m12 like the new 18 volt system they are running hotter than the gen 2 tools did

@johnsxterra9020 Год назад

Buy the combo kit on sale for 200 it's very good for electricians

@brandynh1439 2 года назад

Run the breakaway test again when you can pair the 3453 with the XC5.0 HO battery! I know that lil’ guy can be pushed a little harder. Looking forward to getting mine soon!

@Shoptoolreviews 2 года назад

We'll run some additional tests when we get the NEW M12 batteries in. Thanks for watching.

@AndToTheRepublic4WhichItStands Год назад

Does the hammer drill have a hammer only function to be used like a mini air hammer/chisel? Basically can you turn the rotation off

@MrCaribe65 Год назад

No.

@ChrisBranleh Год назад

Strange that it seems like the m12 impact and drilll seem to have the most iterations compared to other m12 tools

@rstar88105 Год назад

Did they improve the clutch for the drill? The digital clutch would often be too strong for finishing or trim screws even on the lowest setting. I have to do a two step process to run down to get close to seating the fastener and pull the trigger again to get a better clutch reaction for small torque amounts.

@FerralVideo 2 года назад

I'm curious how they stack up against the outgoing 2nd gen, since they have been marked down to make room for the 3rd. I don't necessarily need "all" the power, so if they're "close enough" I'll save a buck and get 2nd gen while they're still available.

@Jtwizzle 2 года назад

I cant speak for the drill but the driver seems to be 20-30% better than the old fuel driver.

@lt3880 Год назад

up to you, but these are still a fair bit smaller which is the appeal of m12 for me.

@sk3tchimdg3t33 2 года назад

For anything above 18mm speed one thats my rule and i never big down not even with a 32mm

@sashaa1960 6 месяцев назад

would be nice to see how these drills perform on metal beams

@wemcal 8 дней назад

Great video

@cucolopez1942 2 года назад

I'm not sure I'd ever upgrade to this 3rd Gen, the 2nd Gen are amazing as well.

@prestigemechanical3600 2 года назад

The M12 Fuel Gen 3 vibrates a lot in the hand. You can feel it most definitely but it is the most powerful 12v impact on the market. However……… the M12 impact with a xc battery is heavier than the Dewalt 20v DCF840 paired with the powerstack. Dewalt makes the best feeling 20v hand tools when you talk about ergonomics, weight and size. It all depends on the user and application the user is the most important tool. I really wish more tests were done in the field to show where and when they shine the most.

@luism.7668 2 года назад

Great video , Thank You for sharing Sir !

@caitlincabang Год назад

The value of these went up recently with the addition of M12’s accessories. Been using the gen3 impact everyday the past 6 months doing low voltage work. Shop vac is ehh but the M12 lights and blower is crazy good. So happy I made m12 my main tool branch. Definitely going to need a 4 or 6 Ah battery for the shop vac and blower but it’s money well spent.

@franklong6269 7 месяцев назад

I greatly enjoy your videos; you do a really good job of explaining and testing the tools. I have a couple of suggestions: 1. Nobody cares if the handle is wider at the bottom of the 12V impact driver. That's not worth your audience's time. 2. On your drill tests with the hammer drill, you are driving at an angle and that causes the drill bit to bind. It is harder to drill wood at an angle. Next time, make sure you are square to the board, and your drill bit probably won't bind. Once again, your video is excellent - great job!

@timweb1510 7 месяцев назад

Wrong

@franklong6269 7 месяцев назад

@@timweb1510 An amusingly stupid response. Don't waste my time.

@timweb1510 3 месяца назад

@@franklong6269you wasted your own time with your foolishness

@franklong6269 3 месяца назад

@timweb1510 You were born stupid, you will live stupid, and you will die stupid. I can't think of a more pathetic existence.

@joehertel8846 2 года назад

there's a pretty good hack on them at the depot rn better if it pops on the deal of the day

@Shoptoolreviews 2 года назад

That's awesome.

@mixmeister9985 11 месяцев назад

Hi great video, what socket are you using in that impact driver, to test the torque, did not know you can use that

@kswis 2 года назад

My gen 2 kit seems to do fine, I do like the lights on the gen 3 but eh, I'm fine for now. Wonder if they'll come out with a new surge too? My most used tool BY FAR

@Shoptoolreviews 2 года назад

You can't argue that the Gen2 tools are great tools. Love the Surge, but not sure if we'll see a new model yet.

@kswis 2 года назад

@@Shoptoolreviews still have around a grand orso of m18s mojaroty of them are collecting dust as the m12 feels better in my hands and has plenty of beans to get what I need done. Not to mention can hang from my pocket with no belt! Hope they give us the tri-lights on the surge. THAT I'll go out n buy

@crpreludeh22 2 года назад

Like all your videos, keep it up 👍

@kylefowler5082 2 года назад

I love my m12 impact with the 2.0 battery. Also worth noting is its a 5 year tool warranty but a two year warranty on m12 CP batteries and a 3 year warranty on m12 XC batteries

@Shoptoolreviews 2 года назад

You are correct. Thanks for sharing.

@ali1t Год назад

Isn't the warranty on the m12 fuel lifetime?

@usmamaslam88 9 месяцев назад

Amazing review

@amazingframingdrywall7388 Год назад

Do you ever think that they will ever have a fuel gauge on their batteries, after all they did come out with 2 new m12 batteries.

@alsacs3635 Год назад

Question: If I carry this impact driver in my truck. Can I use it to remove the lug nuts when I get a flat tire? I just need it to replace a single tire. Not looking to do tire rotations.

@kemicala Год назад

I would get a cheap Ryobi 3/8 impact for that kind of task. Don't need it often and cheap enough to not care if it gets stolen, and it's an impact wrench which is what you want for such a task

@kyledamon480 Год назад

My m12 hammer drill keeps flashing all 4 lights when I semi load it up

@3obardThawn3 2 года назад

What were you using to torque down those bolts to test the drills??? Please and thank you

@petermikus2363 11 месяцев назад

I am looking for my first drill and honestly i didn't even consider this one because it is 12V but honestly that was a mistake

@jaYp90 2 года назад

Gen 2 kits are $50 off at home depot. Is it worth it buying the gen 3 kit or stick with the gen 2?

@ChrisTejada-nl7mh Год назад

Would love to see these with the High output 6.0 ah

@GMToaster 9 дней назад

I remember the first time I used a drill

@teckshengtay166 Год назад

Is that a milwaukee socket adapter bit for the impact driver?

@kennethkuhlman8864 2 года назад

So when do the stubbys and Surge drivers get the upgrade to tri-lights? 😏

@gatordave6629 9 месяцев назад

How well can that drill through mild steel with a step bit

@mexicanstylemodificationan8791 2 года назад

Could I use the impact to change a tire and secure the bolts?

@Shoptoolreviews 2 года назад

Sure, that's fine, but I'd follow up with a torque wrench. Thanks for watching.

@badlands6038 Год назад

Hi, good information. Might be good if you included that you can lock the drill chuck by after tightening to back off to the click. It works on dewalt and reported on all quality tools..

@bruins871 2 года назад

I have some home depots that have these in stock i wanna buy the set but idk if i should wait till labor day because maybe they might have a special with the new set should i wait or just buy it now ?

@georgeferlazzo7936 2 года назад

Hello again Shop Tool Reviews Thank you for another Great Video 👍 Where is this on sale at for $229.00? Do you know if a ratchet will offer? Again thank you 😊

@EggyOrphan Год назад

Hey guys, have a question on your opinions. I've been thinking of getting rid of dewalt atomic kit for these. I hear they are more compact and I don't do construction work mostly small project. The most I'd use is probably a hole saw or forstner. Will this be a good trade off or just stick with the atomics??

@TheYazza1 2 года назад

What's the better battery, 6amp or 5 HO amp?

@MarcM143 2 года назад

Dang, if the Gen 3 M18 Fuel hammer drill gets 150 degree hot drilling Four - 1/4 inch holes in concrete I wonder how this hammer drill will hold up, will probably melt? Maybe I'm doing something wrong but my Rigid from 2015 would handle that task with ease. Everything I have is now Milwaukee though so I'm hoping for the best!

@Ezees23 2 года назад

What? Unless I missed smth OP was reviewing the "M12" Fuel Hammer and Impact - not the M18....

@masonb1100 2 года назад

I drilled 16 holes in 5” concrete other day with a 1/2” concrete bit with my m18 hammer drill. Didn’t get super hot or anything. Had 3 bars left on my regular 5.0 battery. Used the drill for the entire pergola I put up. Super beasty

@AzongLee85 2 года назад

Nice! Really want it!

@battsy2911 2 года назад

225 from 12v. That's crazy!!!

@flex_nyc9885 2 года назад

Any reviews on the M12 3403-20???

@kemicala Год назад

Months later and none I can find anywhere

@TheBushey 2 года назад

Is there a new fuel surge impact?

@mt1885 2 года назад

Do they make the 1/4 with an ANVIL as compact is what I need but 1/4 ANVIL tho. Got the 1/4 A/CDelco impact that is brushless super compact.

@gabespartan 2 года назад

Seeking input: DIY'er looking to rebuild a deck surface and fencing (not much foundation work). Looking for something with enough power. Would this set be best or would I be better off with something 18V? If 18V, which combo kit? Probably looking for something compact. Thanks!

@Shoptoolreviews 2 года назад

If you're doing a lot of deck screws, then I'd stick with 18-20V lines.

@gabespartan 2 года назад

@@Shoptoolreviews oh man, I appreciate that feedback. Looking at 18V's - Metabo HPT subcompact, Makita LXT, Dewalt Atomic (850 w/ stacked), and M18 Fuel (Gen 3 or 4). I value reduced fatigue over brute force (getting the job done quickly, lightweight and ergonomics). How would you rank those 4? Thank you!

@flex_nyc9885 2 года назад

Damn that thing is struggling with a 2x6?

@wingman2k 2 года назад

You didn't really test the driving part of the drill. The clutch never engaged

@philodox7599 2 месяца назад

taking 4 bolts off drained the 2.0 battery by 1/2? Thats useless, I hope it does not drain that fast on other applications.

@jj252-89 6 месяцев назад

쿠드롱 형 탠션 지렸다

@TheSixYardBox 5 месяцев назад

Skip forward to 2:50 because the first couple of minutes he just keeps repeating the model numbers and banging on about the m18 being on gen 4

@nsxproperties560 2 года назад

Those tools are better suited for automotive applications, not construction .

@Shoptoolreviews 2 года назад

I think they're pretty agnostic. Many interior trades could use these. Blinds, cabinets, low voltage networking, electrical finish (switch plates, etc.), and others would be a perfect fit for these. Thanks for watching.