Snowblower No Start: Fix W/O Removing Carb.

Подписаться 135 тыс.

Просмотров 49 тыс.

50% 1

amzn.to/3KhaLcx Milwaukee 3/8" Stubby Impact
amzn.to/3qBCGfJ Torch tip cleaners for Carb Passages
amzn.to/3Icd27c Carb. cleaner Spray
amzn.to/3rtTZhE Carburetor replacement for Craftsman Snowblower
Help support Doublewide6 Repairs LLC by sponsoring his Patreon Account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.

Опубликовано:

4 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 61

@doublewide6 2 года назад

Tools Used In the Video. amzn.to/3KhaLcx Milwaukee 3/8" Stubby Impact amzn.to/3qBCGfJ Torch tip cleaners for Carb Passages amzn.to/3Icd27c Carb. cleaner Spray amzn.to/3rtTZhE Carburetor replacement for Craftsman Snowblower Help support Doublewide6 Repairs LLC by sponsoring his Patreon Account www.patreon.com/doublewide6

@scottandjennydeckert 6 дней назад

Wow. My mechanical knack is a 1 on a scale of 100 and this actually worked for me. Great video. Bring on the snow!

@butler386 2 года назад

Excellent repair of a nice looking snow blower. Great advice on removing the emulsion tube. I had not seen that technique before so that gives me another option. Great job. Thanks for the videos.

@notme2620 10 месяцев назад

Poulan 271 8HP Snow Blower, thanks DW6, that is what I experienced yesterday and knew where the problem was, with the "main fuel jet"/ emulsion tube. The video helped me to remove & clean the jet without any removal of all the tin shrouds. Even though I received my automotive mechanic's license in 1973, followed by heavy duty and millwright tickets, You Tube clips like this beats spending hours going through manuals. Best tip, tipping the machine & removing one wheel. I have also installed a throttle cable, to control the engine speed under load. It's not perfect, but it gives control if the governor doesn't react quick enough or at all sometimes.

@RobertFruhling 5 месяцев назад

Last winter I discovered I couldn't start my Cub Cadet snow blower (I had drained the gas from it at the end of the previous season but didn't run the mower until the gas was gone). I gave your approach a try and it worked like a charm! Thanks for the great idea!

@wildwoodsprings1555 11 месяцев назад

I have the exact snow blower. Thank you for putting this quick video together. You will save me time and $ so that I can do it myself.

@jackhuddleston6830 11 месяцев назад

That’s pretty slick taking the tire off to get to the carb. I have a craftsman snow I bought in 1994. Still runs like a top. Never had the carb off. I don’t have to use it every year and I always run the gas out, if I do use it. Glad I found you RU-vid page to watch your videos.

@guitrus 9 месяцев назад

had the same issue, your tip got her going ezpz, managed to do it without removing the tire too! thanks for the help, saved me a trip to the shop & some $$

@gse244 7 месяцев назад

I like the fix. Did you mention when inverting a snow blower you run the risk of gas leaking out? Big safety issue. And oil coming out the muffler and or fluid locking the cylinder? If they don't understand that they could hurt themselves when pull starting or damage the starter and possibly damage the connecting rod.

@BeersBikesandTheFlag 11 месяцев назад

Double wide!!!! Thank you !!! I did this on my 6hp Troy....worked fabulous!!!!Thanks again.

@doublewide6 11 месяцев назад

Glad it helped

@BeersBikesandTheFlag 11 месяцев назад

@@doublewide6 absolutely 💯 thanks again

@BeersBikesandTheFlag 11 месяцев назад

Mine is a 6hp Troy....

@effenfish661 2 года назад

my troy-bilt blower would only run well when partially choked, and that was from when i first bought it. i finally pulled the emulsion tube and found a small piece of plastic on the outside of the tube. put it back together and it has run great ever since. so this fix is definitely worth trying if your engine surges (hunts) too

@scrambler69-xk3kv 9 месяцев назад

One thing seldom mentioned in these no start condition videos, is corrosion on the flywheel and magneto, usually caused when a piece of equipment is stored in an unheated garage or shed. cold temps and metal usually means condensation which causes rust. Remove the cover surrounding the pull start and look at the flywheel and the mating surface on the magneto if you see rust sand those two surfaces, sand them with sandpaper until the rust which prevents spark is removed and they the surfaces are shiny. You should now have spark at the sparkplug.

@phillipmarlow5267 8 месяцев назад

I have to thank you for this video. I have the same blower I bought last summer. Only used once the winter before. The tank hadn't been drained properly so the darn thing wouldn't start. AFter watching you, I followed your instructions and got it running, thankfully because we just had a foot of snow. I did one thing wrong when inserting the emulsion tube tho. I put it in with the larger end first. Darn this runs tho, but I'll reinstall it with the narrow end first. Thanks again.

@Turningwrenches85 2 года назад

Great tips there. I never thought of the wire for the Tecumseh needle to clean the emulsion tube on the carb.

@mrbubetube 10 месяцев назад

I never thought of using a wooden q-tip to remove the emulsion tube. I don't have those, but now I have a good reason to save my chopsticks hahahahahaha

@harveystephens6115 2 года назад

Learn something everyday! Thanks. Enjoyed. You are a good technical person!

@mustafaghafoor8726 10 месяцев назад

Video helped understand that some troubleshooting can be done but wasn’t clear how you tilt the blower? Did you have to drain the gas? Is there any caution to use when tilting? Other than that you made it seem it like an easy job 👍🏼. I have exact same blower. Won’t start and saw no spark on spark plug. Could you give any tip.

@Big_Johns 2 года назад

At least it was easy to get to, good job Bob. thanks for the video brother.

@rogermcdonald1607 2 года назад

John you could've used a snowblower like that for that big storm you had this winter! LOL. 👍❄🌨

@Big_Johns 2 года назад

🤣🤣 That’s for sure Roger, I was snowed-in for 2 days because I didn’t have one of these beast!! 👍🏼🤣

@mikespain8655 2 года назад

Good alternative method to removing entire carburetor. Probably a Huayi carb if it is a newer snowblower.

@chelsimartin234 8 месяцев назад

But is it though

@nashguy207 2 года назад

Nice easy repair Bob. Thanks for sharing!!

@KensSmallEngineRepair 2 года назад

I like those quiet series engines! Nice simple fix Bob! I sometimes do the same thing on the tailgate of my truck without having to unload it! Nice work!

@larrycroft470 2 года назад

I always enjoy your videos Doublewide 6 !! Not a big fan of snowblowers since we never have use for them here but learning from you more about small engine repair is a great plus!!

@rotex380 2 года назад

Great job as usual dw6 👍 same thing happens to my Honda hs1132 from time to time, but it's a quick fix.. thanks for sharing 🍻👍

@moneyshot7785 9 месяцев назад

Thanks, this worked for me, the emulsion tube was completely clogged

@orbzy183 10 месяцев назад

This video got me out of a jam today. Great job much easier then the 30 minute videos that are out there

@violinplayer7201 8 месяцев назад

Worked for me!!! Appreciated for sharing this!!!!

@martincorona1964 10 дней назад

👍🤜 thank you my friend😊

@stephenzies8867 2 года назад

Good Job !

@kenhilson786 2 года назад

unusual to see emulsion tube clogged but not the main jet.

@KensSmallEngineRepair 2 года назад

I’ve seen where people remove the main jet and clean it not realizing there is a removable emulsion tube to clean as well. Most times you have to push the emulsion tube out from the Venturi while the jet usually just falls out when unscrewed,

@lavendersneppo 2 года назад

I don't think i've ever seen a clogged emulsion tube, since the main jet blocks all of the crap from getting to the emulsion tube in the first place

@vinces8974 2 года назад

Nice work!

@MeepMeep88 10 месяцев назад

1:03 whatcha using to remove the emulsion tube before the little wire? Just a flathead or..

@realestaterider 8 месяцев назад

Yes this was a what I needed!! Thank You great video!!

@hoists1829 2 года назад

awesome video

@marshallborder9089 2 года назад

Good video

@SB-mw1bg Месяц назад

All I had to do was take the plugged jet out and clean it. I added some Stabil about a month ago and got it started today.

@mickdog2 2 года назад

Those carbs are not fun to remove. Good video

@jab3879 9 месяцев назад

Nice video. Do you have to drain the gas before doing this, or by laying it on the side it wont leak out? Thanks

@mustafaghafoor8726 9 месяцев назад

Did you have to take the fuel out to put it in the vertical position? Or to take the jet out?

@KingKatura 9 месяцев назад

why not just use carb cleaning fluid? Just faster to scrape it?

@littlesilver2205 9 месяцев назад

With a Sears snow blower brand new 26'2nd time using used stabilizer fresh gas wouldnt start, it is ridicilous that a 800$ machine should not be doing this brand new ,👍 thank you for your how to, saved me many hours of ripping the carb and all that down . After spraying starter fluid in the spark plug hole, it still would not work could only be that pin is clogged, is it just a bad design , mainly the ethanol they added in to the gas. No other machine i have does this.

@davidm.1098 3 месяца назад

what year is that snow thrower? I just bought the same one and not sure how old it is

@gsettlemyre 2 года назад

Will this fix also help eliminate having to run it on partial choke? Didn’t have to last year, ran like a champ then.

@imacarfreak6036 8 месяцев назад

How did you get the emotion tube out? I didn't see a groove for a screwdriver?...

@organicvids Год назад

135 tobacco pipe cleaner n chemtool.

@user-rw3km9xv7c 11 месяцев назад

My blower is doing the same thing, I cleaned the carb too but it’s still not running. What should I do next? Thank you

@southerncomfort971 Год назад

hi , my cub cadet was running rough, once i finished the last path it slowly sputtered and backfired. Now it won't start? I have been told seafoam might help? what is your thoughts knowing you haven't seen the machine , it is only 3 years old and i have changed the oil yearly new gas each season. Thanks for any thoughts

@henrymurawskibigdogrepair 2 года назад

I saw the dirt on the end of the wire when you pushed it through you missed it Bob

@stephenzies8867 2 года назад

He Might Have Missed The Dirt But Fixed The Problem So Bob Gets FIVE Stars * * * * * For The The Repair

@henrymurawskibigdogrepair 2 года назад

Yes Bob is a star he he can fix almost everything he puts his mind to it he is the best

@jeremyanthony9300 2 года назад

Well well, another LCT engine. JUNK . There becoming more and more common motors on power equipment. Just cleaned a carb on one last week. It was on a cub cadet chipper shredder vacuum.

@howardtaylor229 11 месяцев назад

The long part that goes back into the carb falls out so quick I didn't see which end goes in first on re-assembly and you didn't show that. FAIL on your end.