Sparex Ferguson TEA20 # 28 Fitting the Timing Chain and Setting Cam timing

Подписаться 50 тыс.

Просмотров 20 тыс.

50% 1

In this video I cover how to set up the timing chain correctly and fit it all up.
Here is a link to the Kangaroo Stew where I bought it and got it running.
• Kangaroo Stew # 165 I ...
Some of the links I talk of in the introduction are below.
Queensland Tractor Spares Web Site:
www.queensland...
Queensland Tractor Spares Ferguson Parts Category Short Cut:
www.queensland...
Queensland Tractor Spares Technical Tab:
www.queensland...
Queensland Tractor Spares Downloadable Sparex Catalog Tab:
www.queensland...
Sparex Australia Web Site:
au.sparex.com/

Опубликовано:

8 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 34

@stuartmaier2465 4 года назад

Hi Lance, this is not something you want to read; I have a bad feeling that the chain retainer clip went on the wrong way around (although it's difficult to see). My understanding is that the head points towards the gear that pulls.

@BundyBearsShed 4 года назад

Yes thats what I did I think, I will have to run through now and have a look, lol.

@BundyBearsShed 4 года назад

Yep on back to front. Not a big worry though but I might pop the cover its only a pulley and a few bolts.

@onkargill8236 3 года назад

I've done the same thing 😂 put the chain retainer wrong way even though I was thinking it should be the other way but I thought you can't be wrong 😃🤣 so it's timing cover off again 😅

@TheKnacklersWorkshop 4 года назад

Good video, I really enjoyed it Thank you

@BundyBearsShed 4 года назад

Glad you enjoyed it

@453421abcdefg12345 Год назад

I think you put the chain link clip on the wrong way round, the closed end should face the direction of rotation ,the way it is now could result in the spring leg catching and removing the clip, good luck Chris B.

@BundyBearsShed Год назад

I would need to go back and have a look, it is running well still. Sometimes when filming the end result on the video may not be the actual end result if I have had to do a few takes.

@453421abcdefg12345 Год назад

@@BundyBearsShed i am sure filming and fitting are a very big problem, it must be like trying to talk to someone while you are putting something back together, looking at your re assembly of the timing cover video I can see that if the "mushroom" was sticking in the centre shaft hole that could cause my problem, a video is worth 2 thousand words! Chris B.

@JACKATTACKED 4 года назад

Gravity is back 😂👍

@BundyBearsShed 4 года назад

It never left.

@JACKATTACKED 4 года назад

Wouldn't be right if it never gave you a reminder now and again 😂

@edwardmuirhead6726 Год назад

Good day Lance , I took the 5 bolts off the cam sprocket on my TEF today , lost the settings as I hadn’t realised multiple settings , could you please advise me how to get it back to the correct position please ? Thanks again , Ted

@BundyBearsShed Год назад

I would have to look in the manual it has been that long since I did one. There is a free manual in my website www.queenslandtractorspares.com.au in the technical section.

@edwardmuirhead6726 Год назад

@@BundyBearsShed Thank-you Lance , your help as always is very much appreciated , I will look that up , all the best ! Ted

@connormacmillan839 Год назад

Hi lance, im fitting a new timing chain to my ted 20 tomorrow, the crank sprocket been touched since i took the cam sprocket off, however i didnt put witness marks on the cam sprocket. There is a witness mark etched into the crank pulley but im concerned that ive messed the timing up. Any help?

@BundyBearsShed Год назад

Yes I think there is a mark. Download the manual from my QTS website to be sure. queenslandtractorspares.com.au/technical/

@connormacmillan839 Год назад

Thanks for the help lance, fitted new belt today, top side is pretty tight but underside is sagging, thinking its because the sprockets aren't new!

@darrenblattner2508 4 года назад

So my John Deere has an idler gear rather than a chain. If I set the piston at TDC and set the valves at .010 (or 0) my idler gear should just slide in and mesh nicely? Maybe? possibly? Then with my rotor pointing at #1 piston it should slide in nicely as well? Perhaps? Welders playing mechanics!!!

@BundyBearsShed 4 года назад

For yours you need a steel ruler which welders will have for sure. Just align the marks through the center of the crank and pop the idler in.

@darrenblattner2508 4 года назад

That’s almost to easy Lance. Thanks

@alexandercotter707 4 года назад

Hi Lance, I’m hoping to can help me. I’m looking at purchasing a TEA20 but it has a broken timing chain and timing case cover. My question is it worth repairing or will the pistons have bent the valves? TIA

@BundyBearsShed 4 года назад

Valve will probably be ok as they didnt lift that much really

@alexandercotter707 4 года назад

Bundy Bears Shed Thank you for the advice