Speedy's Garage Hellcat Crank Pinning Continued...

Подписаться 31 тыс.

Просмотров 12 тыс.

50% 1

Join the Channel! / @speedysgarage
Stuff I use:
Race Ramps: amzn.to/2Sicrdt
Race Ramp Low Profile Extension: amzn.to/2MhlDLa
Tire Rack: amzn.to/38X0foa
Cordless Ratchet: amzn.to/2tIMKIK
Cordless 1/2" Impact: amzn.to/2MlxMyL
Cordless 3/8" Impact: amzn.to/2sPLm6K
Ratchet Set: amzn.to/2QbKsJK
Wrench Set: amzn.to/374jt9R
Drill: amzn.to/2FSjnGh
Drill Bit: amzn.to/2G3G2k0
Tool Cutting Oil: amzn.to/2HHdRZi
Breaker Bar: amzn.to/2QmSUW7
Today at Speedy's Garage we finish the project of pinning the crank on our Dodge Hellcat Challenger Go Man Go. Not too bad with the right tools, and we show the difference in the original crank bolt and the new design that comes on all new Hellcats including the Hellcat Redeye and Dodge Demon. This will apply to the Dodge Hellcat Demon as well as the Dodge Hellcat Redeye and Hellcat Chargers. Be careful with the drill bits, they can be brittle and you definitely don't want to break it and get it stuck in the crank snout. I'd recommend using the drill bit I linked to above as well as some tool oil to ease the job.
Don't forget to checkout my website
www.speedysgarage.net
Like us on FaceBook if you do that kinda thing / speedysgarage
Follow on Instagram
/ speedys_garage
Music By:
Joakim Karud / joakimkarud
Dyalla Swain / dyallas

Авто/Мото

Опубликовано:

31 май 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 52

@EPICYELLOWHORSE 6 месяцев назад

I really appreciate the videos. The subscription fee was well worth it. Prayers to your family. I have been over the road as a trucker and missed updates since the car was stolen. Hopefully the thieves are behind bars. Frank

@shift_nation4785 3 года назад

Machinist here .. kit should come w carbide drills , and carbide center drill/reamer finish to prep the hole...so hole is straight...also cutting oil....maybe a snubby/short drill for clearance ....good video keep it up 💪.....

@jettech1041 5 лет назад

The bit that came in my kit wouldn’t even put a scratch on the forged crank. When I settle into the new house I will give the cobalt drill bit with the cutting fluid a try. Oh don’t let Mrs. Speedy see you using her mirror...😁🤣

@westernefficientenergy902 5 лет назад

I like the way your brain works, very meticulous. When you get that lift installed this type work will be so much more pleasurable. Love this channel.

@A-37Bdragonfly 3 года назад

I did the same thing on my 2016 hellcat...you did a great job ...I did my in 2017 ....did 1050 injectors, replace the axles to 1400 hrs each.. replace the driveshaft 4inch Gforce aluminum.... replace the throttle control to 100 mm... replace the exhaust to MF competition... replace the intake to AF Momentum.. replace the upper pulley to metro 2.85......ATI 10% overdrive super dumper..lower it also..and added the front upper adjustable control arms and the rear upper adjustable control arms. Also did a tune ...I have a lot of cash on it .....Man my wife think too crazy for doing All the to my car ...o well...cool video

@jeepguy4499 5 лет назад

I used a cobalt bit on a Milwaukee right angle drill on low speed with plenty of pressure when I did this to my Trackhawk and it worked like a champ. I did a 9% overdrive Innovations West crank pulley and pin kit.

@Happydaz1933 4 года назад

Excellent video, looks like a fairly easy job...or at least you made it easy .....thank you!

@leonardrice2830 5 лет назад

Fantastic! Thank you! 😃 Unlike many, my aim with my Hellcats is not to set it to "hooniganism kill". I'd rather capitalize on the already robust & sound engineering, while ironing out weak points to yield a solid, respectable, & reliable performer. 🤔 Along with the well known driveshaft/diff bracing modification, I consider this crank pinning good insurance, even on a stock Cat.🤔

@James-Orr 5 лет назад

I don't understand why Chrysler does not pin these high dollar engines either. I broke the ATI pin kit bit on mine and have used Milwaukee bits on mine, my wifes car, and my buddies car on the same bit. It cuts super smooth. At least your about ready to turn up the boost with no worries now!

@franklyle2798 5 лет назад

Guessing you didn't need to go to the gym after tightening that crank bolt. 😁 I agree...there should have been a key on there from the factory...

@JB-zn1kx 5 лет назад

Yippee... more content from Speedy!

@michaelscott3950 5 лет назад

Since I have suffered the same fate pinning for my Kenne Bell on one of my older SRT's. The trick is to drill little then blow out, then drill then blow out trust me it's the best way. Good luck

@SpeedysGarage 5 лет назад

Good info.

@armandomontezuma4701 5 лет назад

Great video keep up the good work. Greatly appreciated!

@MrPappysCobra 4 года назад

You do great work brother!

@Nowhere101 5 лет назад

Thank you for teaching me something.

@BERZERKERSV4 4 года назад

What separates your videos from the “herd”, is the fact they are straight forward, no stupid music during your installs and especially the fact that you don’t have a moronic sidekick .....

@bmasontv 5 лет назад

Very nice!

@kbrx4310 3 года назад

The pin should be below the balancer surface even with the crank so the balancer bolt washer doesnt tighten against the pin and not the balancer .

@BulletSpoung 4 года назад

If anyone at a dealership ever gives you any crap about the mods on your car just tell them watch your videos. You do a much better job than any tech they have. I can see that you're very picky and precise about everything you do so if they start blowing you any shit just tell them to shut the hell up and stand aside.

@SpeedysGarage 4 года назад

LOL

@markbevilacqua3415 4 года назад

Awesome job! Doing my 2020 Redeye next week. Can you tell me if the depth of the pin is Supposed to sit flush with the pulley itself or the actual crank? I see there is a small step down between the pulley and the crank. Thanks! By far the clearest and most detailed videos out!!

@SpeedysGarage 4 года назад

I measured EXACTLY to the specs the kit dictated. It did look like the pin sat just a hair deeper and I think this is due to the incredible torque placed on the crank bolt. Just make sure to measure three times and drill once :)

@FullOutPwr 5 лет назад

Do you have a part # or otherwise for that crank bolt service tool? Seems like it would be near impossible to keep a socket from slipping off a bolt without it.

@toddrancourt8153 Год назад

Were can I get one of those crankshaft locking tools you use to lock the crankshaft to remove the crankshaft bolt to do the pinning thanks todd

@SpeedysGarage Год назад

I got it at the dealer parts dept.

@nhra7110 5 лет назад

Speedy, isn't the pin captured in blind hole one one end, and underneath the big washer on the crank bolt? Wondering the need to Loctite it in there?

@SpeedysGarage 5 лет назад

I'm a belt and suspenders kinda guy 😎

@nhra7110 5 лет назад

Gotcha - me too, but wondering if it might a bear to remove if ever the need arose...

@SpeedysGarage 5 лет назад

It's definitely not ever coming out, but not sure it would ever need to. I didn't want it vibrating over time enlarging the hole or something.

@ogtimmy2355 4 года назад

Can we just use the upgraded bolt and not pin the crank? I may only tune the car and not change any pullies, or just add the Hellraiser upper. I've been binge watching your channel for the last 2 days and it's awesome 👍

@SpeedysGarage 4 года назад

You can just upgrade the bolt, but I'm a belt and suspenders kinda guy.

@arthaitu7430 2 года назад

I have a shop pinning the crank, im sure they will not be so meticulous as you are, and im scared of that.

@jeffsmystic 5 лет назад

Nice Speedy👍 did that low intercooler coolant light clear?

@SpeedysGarage 5 лет назад

Yes.

@norcalsrt1214 5 лет назад

Post up the info on the tool u borrowed I can not find it on snapon

@SpeedysGarage 5 лет назад

P/N 10386 Vibration Damper Holder

@jp34787 3 года назад

Speedy, where can you get the adapter tool to put on the crank when tightening the new crank bolt to prevent spinning and what is it called?

@SpeedysGarage 3 года назад

I borrowed it from my local dealer.

@victorymotorsports9258 5 лет назад

Right after I watch this video I took my 2017 hellcat with only 3000 miles for a drive. Two minutes into the drive I lost power steering, AC, voltage light and check engine light came on. First impression was my belt slipped off check the belt it was on, power steering fluid was full of fluid. Took it into the dealership and they just called me and said my crank bolt loosened off and my crank pulley is spinning freely. They said they are going to replace the bolt and pulley but do you think there something else I should be worried about and look for. Love your videos keep up the good work.

@SpeedysGarage 5 лет назад

"Usually" when the crank pulley spins like that, it damages the crank snout. I'd be leery of the dealer just putting in a new bolt without some kind of documentation that the crank was shown to be good (with pictures).

@fredpierson7488 4 года назад

You can get a torque wrench that reads degrees

@SpeedysGarage 4 года назад

You can also get a degree tool that attaches to standard torque wrenches as well.

@kirkmiller9852 5 лет назад

Do you have the 67" race ramps?...think they raise the car 10". From watching you I dont think the 56" versions that raise the car 8" would allow you enough room to remove the fan

@SpeedysGarage 5 лет назад

I'l have to measure them.