Suzuki Katana Rear Brake Pad Change

Подписаться 1,2 тыс.

Просмотров 6 тыс.

50% 1

My rear brakes were starting to squeal so it was about time to change them out. I wasn't able to find a RU-vid video or guide out there for replacing them, so here is mine. Good luck!
Brake Pads from eBay:
ebay.to/2CIe3at
Thanks for watching! If you like my content please like and subscribe and consider following my Instagram account!
Instagram: @JustinsHomeGarage
/ justinshomegarage
Website: bit.ly/justinsg...
Like my gear? Check it out on Amazon and support the channel all at once:
Helmet:
amzn.to/37lqJyO
Pants:
amzn.to/2OFH3lN
Mask:
amzn.to/331rjOU
Shoes:
amzn.to/2O10C8W
Gloves:
amzn.to/2KDf7NV
Backpack:
amzn.to/35jq3sc
Jacket:
amzn.to/37lv1Xe

Опубликовано:

15 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 17

@gordiem10 Год назад

How hard was the dash change ? Where did you get it what is the model

@JustinsGarage Год назад

I have a video on it. Not hard if you have time and wiring knowledge. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ka8bCEspcBA.html

@ParamedicSafety 2 месяца назад

Unbelievably helpful video. Very successful. One find, our swing arm bolt was facing in the same direction. I think this is intentional when built. Well done! Thank you!

@CPDRollo53 2 года назад

Great video.....very helpful. BTW the bolt from that bar is on the way it was from factory. The 14mm head of my bolt was on the inside and the nut was on the outside....why I dont. My only guess is that there was a need to maximize clearance on the inside and the nut is thicker and the bolt would also pop out past the nut versus almost flush with bolt on inside.

@hordurvilhjalmsson1867 2 года назад

You should put some anti-seize on the pad pins only where they sits in the caliper they can come rusty and hard to get out

@double0034 Год назад

Good video helped a lot 💯‼️

@prestonpetterson4990 Год назад

THANK YOU!!

@josephjanampa1493 2 года назад

What year is the bike because the dash seem to be electric rather than the mechanical

@josephjanampa1493 2 года назад

What year is the bike cause your dash seems to be electric not the mechanical one

@JustinsGarage 2 года назад

It is a 2001 Katana. The dash is a custom unit I installed on it. I have a few videos on it on my channel with links and guides.

@richardj2927 2 года назад

I'm a pro first,if this job isnt shown in the manual than its crap. Also there is no need to pull the caliper. Just the 2 pins and thats it

@goadmerle 2 года назад

How did you compress the piston while it was still on the bike? Had this bike 2 years and became a pro at carburetors. Now working my way down🤣. And i love short cuts

@richardj2927 2 года назад

@@goadmerle use a small screwdriver and force it gently between one pad and the disc

@goadmerle 2 года назад

@@richardj2927 didn't work for mine. It still had the original pads. Containing a shim, and a tension spring. Ended up throwing those away because the new pads had a thicker steel plate. Now i can change them without removing the caliper. So next time will take a few minutes. Thank you.

@richardj2927 2 года назад

@@goadmerle sorry but then you didnt do it right. As said,I'm a professionell who did these jobs many years. If you cant pry the screwdriver between the pad and the disc you have to start gently on the edges of the pad. There is always enough room for it. Another way is to just hit the caliper with a hammer.Never had a working one that wasnt movable in one of those ways