Тёмный

Symptoms and Signs of Bad Distributor and How to Fix It 

HVAC Mechanic
Подписаться 62 тыс.
Просмотров 86 тыс.
50% 1

The symptoms and signs of bad engine distributor and how to fix a failed distributor.
Symptoms of Bad Distributor:
Check Engine Light On
Engine will Not Start
Engine Runs Badly or Rough
Engine Misfiring or Backfiring
How To Fix a Bad Distributor
Examine the Distributor Cap and Rotor.
Replace the Rotor
Replace the Distributor Cap (Be sure to transfer the spark plug wires correctly).
Replace Entire Distributor.
www.backyardmechanic.org
By using this information user assumes all risk of use.

Хобби

Опубликовано:

 

1 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 64   
@RicardoDiaz-mb9wm
@RicardoDiaz-mb9wm 6 месяцев назад
Thats a freakin good video. Straight to the point, clear, concise. Loves the recap. Liked, subscribed.
@wilfredotreto07
@wilfredotreto07 8 месяцев назад
Tanks for the explanation. And taking your time for this.🤝🤝🙌🙌
@mikekosloff6926
@mikekosloff6926 10 месяцев назад
Great simple info !👍🏻
@wordswritteninred7171
@wordswritteninred7171 Месяц назад
Thank you!
@TXXNova
@TXXNova 2 месяца назад
Thank you. ❤
@kalebstout7673
@kalebstout7673 Год назад
Got a 02 Chevy express van 1500 with the 5.7 Vortec and at first thought the problem was with the Transmission Range Sensor/Neutral Safety Switch due to pulling code P0706 and P0300. Took it to a trans shop and they said that the sensor is working perfectly and that the code was old in the history. The van only has 17,000 original miles but sat on and off for a while. I figured a wire might have been chewed by a squirrel or rat but once reassured by the trans shop that the sensor was good and they the engine has a severe misfire I took it to another shop. The new shop tried to say I needed to replace the sensor (red flag) and that the distributor cap was charred and I should replace the whole distributor! (Another red flag) just curious how likely it would be that I do in fact need to replace the distributor and not just the cap and rotor being the vehicle only has 17000 miles on it. Also just to note I replaced the cap and rotor, spark plugs and wires less than a year ago. Van is super sluggish, poor fuel economy, loss in power and recently won’t start and even died on the road a few times.
@Antique803
@Antique803 11 месяцев назад
How much can the dwell vary With engine running? I set mine for 27, it varies from 26.5-27.5 while idling. Is that normal or does that mean I have too much wobble in the distributor shaft? I have a vibration in park at different rpm’s. I just swapped out the harmonic balancer. Seems smoother driving down the road, but still has vibration in park or neutral.
@carlcatron130
@carlcatron130 5 месяцев назад
Had the same problem. Random misfire tab on rotor keeps breaking ended up replacing distributor.
@joe187976
@joe187976 Год назад
Mine leaking oil. Would this effect engine power in my b18 ir just dosent have that same pull.
@codymunoz3901
@codymunoz3901 3 месяца назад
If i had 5 dollars for everyone you said distributor, id still be broke
@FcCopa90
@FcCopa90 2 месяца назад
😂😂
@jballs1118
@jballs1118 8 месяцев назад
I have a 1965 mercury comet straight 6 3.3L my problem is the car start fine and doesn’t die when is park but when I start driving after 2 miles the car dies on me. Can you give me an advice if possible thanks 🙏
@davyboone1794
@davyboone1794 3 месяца назад
98 toyota 4 runner idles perfectly, but as soon as you put it in gear no power and lots of backfires. Could that still be a Distributor?
@blshotlexusjay9537
@blshotlexusjay9537 10 месяцев назад
I have a GMC Jimmy 2000 the distrubotor cap had all 6 pins corrodded replace cap and rotor and does not crank check the cable from the ignition coil to the distibutor and im getting spark but im not getting spark comming out what can it be ????? some help
@gknettel22
@gknettel22 8 месяцев назад
How long will a stock distributor typically last? My dodge 5.9 magnum has 182k feeling its time
@tuscancmh
@tuscancmh 9 месяцев назад
It would be helpful if you showed what good and bad parts of a distributor should look like.
@benjamincamarilloloza9012
@benjamincamarilloloza9012 5 месяцев назад
Can a bad distributor causes white smoke that smells like too much fuel? Runs little rough but has new coil and wires, good sparks and new ICM Is a F150 1995 throws some codes but related to EGR
@lionsg8426
@lionsg8426 10 месяцев назад
I sprayed my engine with water and now truck wont start it just cranks and makes pop noises is this distributor???
@Fiingaz
@Fiingaz 9 месяцев назад
My car 1994 jeep cherokee will not turn over. Just cranks only! Gonna try this out
@sonickchri
@sonickchri 6 месяцев назад
I had a random misfire issue and took the distributor cap off. It might have looked slightly rusty with some rusted dust inside but everything looked good for the most part. I put it back on, being careful to label the spark plugs to ensure everything is connected in the correct order and now when starting I sometimes get a split-second awful grinding noise initially. Is it possible that I need to replace the distributor/rotor?? Thanks.
@hannashoulders3357
@hannashoulders3357 5 месяцев назад
Yes the thrust bearing is bad and that sound is most likely it hitting the cam sensor
@sonickchri
@sonickchri 5 месяцев назад
@@hannashoulders3357 Thanks for the advice. The sound went away and I later replaced the spark plug wires which finally fixed the misfire issue.
@leelajapheth4051
@leelajapheth4051 5 дней назад
I accidentally removed one spark plug cable. The shortest one. I drove the car Then car stopped Put back the cable didn't help How to repair the distributor??
@marvinyoung2142
@marvinyoung2142 9 месяцев назад
I have a question if that’s fine my mechanic is a good dude but he slow with finding issues I bought a high performance engine and he said he heard a popping noise the engine was checked and compression test was done but I think it’s the distributor Wht do u think
@crustylard
@crustylard 8 месяцев назад
Hard to know without actually hearing the popping noise, could have been a misfire due to distributor tho
@user-ox9lq8vl3c
@user-ox9lq8vl3c 5 месяцев назад
I have a Joyner 650 sand spider. Put new distributor cap, new ignition coil, new plug wires and new plugs. Engine turns but not getting spark. Could it be the distributor needs to be replaced or possibly wiring? I get power to ignition coil according to my meter/tester. Side note, I couldn’t find ignition coil for the buggy but the guy at the parts store recommended a coil off a 79 F100. Both 12V so not sure if the coil could still be the issue. Any recommendations would be greatly appreciated. Thank you
@HVAC_Mechanic
@HVAC_Mechanic 5 месяцев назад
It could be any of those things. Was it working before replacing all the parts? You could swap them back in one at a time to see which is the issue.
@user-ox9lq8vl3c
@user-ox9lq8vl3c 5 месяцев назад
I got it from a buddy that bought all new toys and didn’t want to mess with it anymore. It was all running fine till he broke the drive shaft. He took it all apart to replace the drive shaft and also did the hydraulic steering, radiator, alternator and clutch. When he put everything back together it would only turn but not fire. I have done the previously mentioned trying to trouble shoot the problem. Has brand new battery as well and plenty of juice in that to turn it. Not sure if this is worth mentioning but, when I pull it and pop the clutch it fires but as soon as I hit the gas it bogs and when the pull stops it kills. That through me off to because it sounds like a fuel issue is a possibility too.🤦🏼‍♂️ Probably over my head on this one and it is most likely something little and easy but I’m not seeing it. Thanks
@Quaylokeepitg
@Quaylokeepitg 5 месяцев назад
My rotor is stuck on and will Not come off with my bare strength what are the suggestions
@angusmcpherson
@angusmcpherson Месяц назад
I put paint stirring sticks under my rotor, then put screw drivers on both sides between the sticks and the old rotor. Gently tap with a small hammer the screw driver handles and they will wedge the rotor up and off the shift without leaving tool marks on the distributor.
@latamorewilliams6443
@latamorewilliams6443 10 месяцев назад
🚨🚨I have a 1987 Chevy g20 van . I purchased a eBay distributor n put in it. I’ve replaced mostly everything new. But my issue now is when I’m driving and it rides like it should before it start’s warming up, then once warmed up I’ll drive 10 mph, 20mph and then it will want to idle up in like I’m on the interstate riding and coasting like I’m going 50, but in actuality I’m doing 35? Then when I stop at a light it runs VERY VERY LIGHT , like I can’t tell if it’s on or not. Something’s happening from when I start driving it has good power and then later it’s like very low idle too smooth. 😖 please help me.🤝
@rahccigang1345
@rahccigang1345 3 месяца назад
Did you ever find out if it was the distributor?
@latamorewilliams6443
@latamorewilliams6443 3 месяца назад
@@rahccigang1345 not yet, I’m suspecting it could be the computer, because I put on everything new, trying to troubleshoot can be difficult especially if your on a budget. What problem do you have with yours? I know I did buy a cheap distributor from eBay. I will get a new more expensive one.
@ashleyshavers4374
@ashleyshavers4374 Год назад
94 f150 5.0 I replaced the ignition control module and the ignition coil and new plugs and wires and now it has a misfire could that be the distributor?
@alonsozuniga91
@alonsozuniga91 Год назад
Yes and also check the camshaft sensor
@athensboy123
@athensboy123 Год назад
​@@alonsozuniga91I have a question? The camshaft sensor those numbers crank pulley? Isn't that where you use a timing light?
@athensboy123
@athensboy123 Год назад
Hey just wanted to say I got a 1995 f150 with a 5.0 302... Just the other day which is now 6-21-23 how to replace ignition control module and put a brand new ignition coil from AutoZone and I'm still not getting my truck to crank.. now it's not fuel pump so I'm having the same problem.! I'm thinking it could be distributed because it does work with ignition coil
@vikingbrowski3718
@vikingbrowski3718 8 месяцев назад
​@@athensboy123I have same truck and currently having same issue you figure it out?
@jermainemartinez-oe5gt
@jermainemartinez-oe5gt 11 месяцев назад
I have 4.3 v6 99 Sierra was getting random p0300 so I bought new plugs and started getting a cylinder number 2 misfire so changed out all spark plugs then got a p0300 code so I changed out distributor cap bc the distributor is new and now getting a no start just crank
@blshotlexusjay9537
@blshotlexusjay9537 10 месяцев назад
having the same exact problem did you figure out the problem
@jermainemartinez-oe5gt
@jermainemartinez-oe5gt 10 месяцев назад
@@blshotlexusjay9537 cracked cylinder heads did myself a favor and cut my loses sold the truck
@ElPadrino610
@ElPadrino610 9 месяцев назад
Crankshaft position sensor, it's at the botto. behind the harmonic balancer, good luck!
@jermainemartinez-oe5gt
@jermainemartinez-oe5gt 9 месяцев назад
@@ElPadrino610 one of the 1st things I did was replaced my crank sensor wasn’t that ez of fix for me
@cyprexx1946
@cyprexx1946 6 месяцев назад
Can this be my problem? I have a 2009 lincoln mkz and i have school from 7:30 to 4:30 so i wake up at 6 to warm my car but since its so cold outside it runs horrible even when my temperature gage is in the right spot and then when i try to drive it the wrench symbol comes on and theres hardly any power to the vehicle when i try to drive it. but as it starts warming up near the afternoon like around 11 or 12 it runs completely fine and the wrench symbol turns off this problem has been so difficult to deal with since me and my dad can figure out the issue.
@Wolfshalifi
@Wolfshalifi 10 месяцев назад
Would it cause a false start?
@crustylard
@crustylard 8 месяцев назад
Could be, could be a fuel issue aswell as battery
@BUKWulfSh0t
@BUKWulfSh0t Год назад
Dude i just got mine replaced and im still getting misfire on cylinder #3
@BUKWulfSh0t
@BUKWulfSh0t Год назад
400$ dwn the drain
@HVAC_Mechanic
@HVAC_Mechanic Год назад
Double check the firing order. It is easy to get two spark plug wires off which will cause issues.
@athensboy123
@athensboy123 Год назад
I'm having the same problem today 6-21-23 TODAY and it's raining which is just my bad luck.. no shop either.. but my problem is when I put the new in ignition control modular and the new ignition coil I'm getting a constant instant pulsing spark? What's that about? Never seen that?
@BUKWulfSh0t
@BUKWulfSh0t Год назад
These jeeps are a pain in the as!!!!
@likegaston
@likegaston 3 месяца назад
Me lchanic told my wife she needs to fix distribution every 30000 miles for $600. Is she being scammed?
@Randomness662
@Randomness662 3 месяца назад
distributor for my car is around a $90 part, and it'll take no more than 15 min to replace. that's just my car tho, so do with that info what you will
@Luke-ofStoke-Factor
@Luke-ofStoke-Factor 11 месяцев назад
I am Stranded. No money. I have to replace distributor on 97 nissan sentra.
@lionsg8426
@lionsg8426 10 месяцев назад
I sprayed my engine with water and now truck wont start it just cranks and makes pop noises is this distributor???
@lionsg8426
@lionsg8426 10 месяцев назад
I sprayed my engine with water and now truck wont start it just cranks and makes pop noises is this distributor???
@lionsg8426
@lionsg8426 10 месяцев назад
I sprayed my engine with water and now truck wont start it just cranks and makes pop noises is this distributor???
@lionsg8426
@lionsg8426 10 месяцев назад
I sprayed my engine with water and now truck wont start it just cranks and makes pop noises is this distributor???
@crustylard
@crustylard 8 месяцев назад
Maybe try taking of the distributor cap, could have lots of water and making the connection bad
@lionsg8426
@lionsg8426 10 месяцев назад
I sprayed my engine with water and now truck wont start it just cranks and makes pop noises is this distributor???
@HVAC_Mechanic
@HVAC_Mechanic 10 месяцев назад
Let it dry out and it will likely start.
@lionsg8426
@lionsg8426 10 месяцев назад
It's been a day and truck no longer mis fires but still doesnt start
@THEMOUSTACHEGUY3545
@THEMOUSTACHEGUY3545 9 месяцев назад
You figure this out?
@lionsg8426
@lionsg8426 9 месяцев назад
@@THEMOUSTACHEGUY3545 nope but truck is in shop now and was told I might have damaged my Ecm when spraying with water
Далее
Installing a Distributor Part 1
7:09
Просмотров 1,3 млн
КАК Я ЭТО СДЕЛАЛА?
00:13
Просмотров 438 тыс.
Symptoms Of A Bad Distributor Cap
10:34
Просмотров 23 тыс.
How To Fix a Honda That Died (Distributor Replacement)
3:20
Misfire,backfire wont idle?easy clean cap & rotor
7:14
7 Bad Distributor Cap Symptoms & Replacement Cost
4:46
РЫБАЛКА ДОМА
0:17
Просмотров 17 млн