Tascam 388 Studio 8 Repair - Part 8

Подписаться 3,7 тыс.

Просмотров 1,7 тыс.

50% 1

It's been almost 4 years, but this thing is back in the shop for some more TLC. This time we have at least one dead channel. Watch me dig into diagnosing and fixing the issue. There will be more in this series in the coming weeks, so stay tuned!

Хобби

Опубликовано:

6 ноя 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 15

@jareddunn11 3 дня назад

great video!!! keep them coming

@MorrisBlaster Год назад

Thank you soooo much! Same issue on one channel that wasn’t working on my 388. This invaluable information saved me from dishing out hundreds at a repair shop. Found NE5532 chips at a local electronics shop for $2 each.

@psychonaut5994 2 года назад

love the series! just recently got my hands on a 388 and looking to do a deep clean, and bit of restoration. would love to see part 9, this would be incredibly helpful as i’m about to dive into this beast. thanks for all the help thus far !

@RegebroRepairs 2 года назад

I got such bad GAS for a 388. But I neither have the need, the space, or the money. :-) So similar to my M-2524 internally. Good to know. If I ever find a broken one, I can likely fix it and sell it on.

@suedelacy 2 года назад

WE ALL NEED PART 9!!

@Musinformation96 2 года назад

Glad to see you back at it with this machine, your videos have been so helpful.

@Mark_Bayer Год назад

More of these would be awesome

@burtreynolds2969 2 года назад

Great video. Is part 9 out yet? Thinking about doing some work on my 388. Especially getting the meters and levels set. Looking forward to it.

@marcblanchard6144 2 года назад

Capstan motor dead on my 388! Where can I find one! Please help!

@user-rn4vg5rk5m 5 месяцев назад

I HAVE A388 THAT WONT GO FORWARD OR REVERSE ITS NOT THE BELT A SPEAKER CORD WENT IN THE WRONG PLACE IN THE BACK MY NEPHEW STUCK IT IN THE WRONG PLACE IT MADE A POP AND NOW IT WONT PLAY OR REWIND WHAT COULD IT BE THAT HAPPENED PLEASE HELP.

@6832jack Год назад

Hello, I have a very basic question on opening up the bottom panel of a 388. I can get all the screws off mine except for the two small screws near the power supply vents on the bottom of the machine. I feel like I'm going to strip the screws with a regular screwdriver, is it best to just order a set of assorted sizes?

@PhillipsHomeRepair Год назад

If you're worried about the screwdriver ruining the head, try an impact driver, either a hammer-operated one or an electric one. (Obviously hammer gently.) Sometimes I've been able to grab the head of the screw with vice grips and back it out that way. I think the bottom screws are M3, so you should be able to get them at any hardware store if they become ruined. Never reuse damaged screws or the next person who needs to remove them will curse you.

@6832jack Год назад

@@PhillipsHomeRepair Thanks a lot. Yeah the two screws beside the power supply vents are smaller than the rest of the screws on the bottom, I'll definitely try an impact driver when I pick up a few other screwdrivers hoping I can find one that can get the right snug fit. Those old Tascam screws can be on the soft side, I had to dremel a couple on my 38 in the past