Tasmota - How To Automate A Light Using A Motion Sensor With Rules And Timers

Подписаться 362

Просмотров 15 тыс.

50% 1

How to create an automated motion controlled light using Tasmota Rules and Timer commands.
Instructions Click More Below...
New rule as reports previous rule can cause motion loop
RuleTimer2 is a buffer to prevent the light turning off triggering another turn on event.
****************************************************
Rule1 ON System#Boot DO Var1 1 ENDON
Rule2 ON Power1#state=1 DO Backlog0 WebSend [mylight] Power %Var1%; RuleTimer1 20 ENDON
ON Rules#Timer=1 DO Backlog0 Var1 0; WebSend [mylight] Power OFF; RuleTimer2 4 ENDON
ON Rules#Timer=2 DO Var1 1 ENDON
Rule1 1
Rule2 1
****************************************************
Old Rule used in video:
Rule1 ON Power1#state=1 do Backlog WebSend [mylight] Power On; RuleTimer1 20 ENDON ON Rules#Timer=1 DO WebSend [mylight] Power OFF ENDON
Tasmota Device Templates:
templates.blakadder.com/
Accessing device via hostname
mymotionsensor
mymotionsensor.lan
Tasmota Commands:
tasmota.github.io/docs/Commands/
Note: The Tuya motion sensor would need flashing to Tasmota, these devices are not pre flashed.
templates.blakadder.com/CT61W...
How To Flash Motion Sensor With Tasmota - • Tasmota Firmware - Fla...

Наука

Опубликовано:

12 июл 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 16

@clairerovic Год назад

I have 20 + Tasmota devices. This was clear to the point and practical. Thanks 👍

@JC-zw9vs Год назад

Superb explanation. Many thanks

@primetechguides3050 2 года назад

NOTE: The Tuya Motion Sensor device would need flashing to Tasmota, this device does not come pre flashed. The Rule is in the description, expand it / show more.

@vanderleisilvasantos5343 2 года назад

hi great video, can I make my own sensor motion with ESP and if is possible to create rules with alexa

@kevinlee3334 10 месяцев назад

I've got an issue where when the light goes off, the motion detector senses that as a motion and again turns the bulb on.... it becomes a cycle of on-off-on-off.... any way to rectify this?

@primetechguides3050 10 месяцев назад

Try this remember to enable both rules - Rule1 1 and Rule2 1 Then reboot device. Rule1 ON System#Boot DO Var1 1 ENDON Rule2 ON Power1#state=1 DO Backlog0 WebSend [mylight] Power %Var1%; RuleTimer1 20 ENDON ON Rules#Timer=1 DO Backlog0 Var1 0; WebSend [mylight] Power OFF; RuleTimer2 4 ENDON ON Rules#Timer=2 DO Var1 1 ENDON

@jasonmarriott1058 2 месяца назад

Is it possible to display the rules created on a unit

@primetechguides3050 2 месяца назад

you mean when you just type Rule1 on the console?, it should be in the output

@navdeepsidhu7178 2 года назад

Hi, can you please help me to get mqtt host name with rules?

@primetechguides3050 2 года назад

I've not done much with MQTT but I believe its in Configure > Configure MQTT > Topic to change the name. This video just for direct communicating between devices.

@dumindujayasinghe 3 месяца назад

Where is the automation run on. A node red or pc or a cloud or on the same esp. ?

@primetechguides3050 3 месяца назад

Doing it this way was just direct Tasmota device to Tasmota device communication using a http request.

@dumindujayasinghe 3 месяца назад

I’m currently using 8 relays and one dht22 sensor on same esp32 running tasmota. So will i be able to use that dht22 data to turn on/off a relay in same esp board via console? Thanks

@primetechguides3050 3 месяца назад

@@dumindujayasinghe For sure. similar concept in this video, using Websend and referencing the devices IP address or hostname, I think chatgpt might be able to draw up the basics of what you need, rule wise

@dumindujayasinghe 3 месяца назад

Thanks you very much. I’ll look for it. ❤