Тёмный

TEQ Customs Retrofit Headlight Install (3rd Gen 4Runner / 1st Gen Tacoma) 

Timmy The Toolman
Подписаться 87 тыс.
Просмотров 15 тыс.
50% 1

Did our video help you? If so, consider buying us a beer: bit.ly/3feE6tJ
We are BACK with some more sicmods, and in this video, we install some projector retrofit headlights from TEQ Customs into our 3rd gen 4Runners. TEQ Customs is based out of Raleigh, North Carolina and specializes in headlight retrofits for a variety of vehicles. They also offer sales and installs of a lot more like suspension, armor, roof racks, roof top tents, etc. They are a one stop shop for your off-road needs.
**Check out TEQ Customs online so you can order a set of custom retrofit headlights, or order a multitude of other items they sell like custom grilles, off-road lighting, suspension upgrades, armor, roof racks, bed racks, bed toppers & camper shells, roof top tents, awnings, air compressors, winches & recovery gear, switch systems, power systems, storage and drawer systems, molle panels, fridge/freezers, communications, wheels, etc.
teqcustoms.com/
*SPECIAL NOTE*
3rd Gen 4runners and 1st Gen Tacomas have different headlights. When making your order, make sure you are getting the right ones for your model and year.
Since 3rd Gen 4runners and 1st Gen Tacomas have very similar front ends, drivetrains and wiring, we decided to include 1st Gen Tacomas into the title because you could successfully use this video as a tutorial to swap in some TEQ Customs headlights into your 1st Gen Tacoma using our video.
*SUPPLIES FOR THE WIRING*
*11 Roll Wire Pack (Multiple Colors) amzn.to/3iwCzjI
*Split Wire Loom Set (1/4", 3/8", 1/2") (To protect the wires - Good general kit for most wiring projects) amzn.to/3AOtgBb
*Shrink Tubing Kit - (to have a weather proof and nicer finished look for the wire connections if you decide to solder) amzn.to/3gIcWY8
*Heat Shrink Butt Connectors (These are the connectors I used to tap into the turn signal wiring) amzn.to/3gSpxbH
*HELPFUL TOOLS*
If you're looking for other tools not used in this video, check out Timmy's Master Tool List.
www.amazon.com/shop/timmythet...
*1/4" and 3/8" Flex Head Ratchet Set amzn.to/2ql8nNA
*3/8" Drive 6 Point Metric Standard Socket Set amzn.to/32WIh0M
*3/8" Drive 6 Point Metric Deep Socket Set amzn.to/37iQjVt
*1/4” Drive 6 Point Standard Metric Socket Set amzn.to/2QIU7te
*3/8” Drive Regular Extension Set amzn.to/2OehCao
*Flex Head Box End Wrench Set amzn.to/31x8BOo
*Milwaukee M12 3/8” Cordless Ratchet amzn.to/2utRZsE
*Milwaukee M12 3/8” Cordless Extended Reach Ratchet
amzn.to/3kOsUS6
*Milwaukee M12 Battery amzn.to/3FJZO1j
*Milwaukee M12 High Capacity Battery amzn.to/2HEFTpu
*Milwaukee M12 Battery Charger amzn.to/2uo2o9x
*JIS Screwdriver amzn.to/31nlP0f
*20 Piece Screwdriver Set amzn.to/34aLrQ1
*Auto Trim Removal Set amzn.to/37vgzvH
*Wire Cutters - (used to cut the wires to size for this job) amzn.to/3wXoj7l
*Interchangeable Ratcheting Terminal Crimper Set - ( A very nice crimping tool for electrical work) amzn.to/2WNq5or
*Wire Strippers/Cutters 8-22 AWG Wire - (Very nice wire strippers. A definite step up from your usual wire strippers most people have in their tool box) amzn.to/2GrRAOU
*Heat Gun - (to shrink heat shrink tubing and shrinkable terminal ends) amzn.to/2DhDf47
**As Ebay Partner Network members, we earn commissions from qualifying purchases.
**As Amazon Associates, we earn from qualifying purchases.

Авто/Мото

Опубликовано:

 

30 авг 2023

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 103   
@benzoil0453
@benzoil0453 11 месяцев назад
Not often you see a company attempt to right the wrongs of a shady/dishonest company. Pretty neat, ill definitely throw some business their way. Thanks Tim and Sean
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Yep, it's way cool of TEQ Customs to help out the people that were ripped off by BXBuilt. Thanks for the comment!
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
​@@TimmyTheToolmanI agree very cool of TEQ
@safeteyvalve
@safeteyvalve 11 месяцев назад
A highway patrol officer told me once for the adjustment of the headlights, have the shortest loved one that drives in the family sit in their car in front of the car that’s having the lights adjusted and lower or raise the headlight beam so they aren’t blinded. I especially liked the officer’s description because every oncoming driver is someone’s loved one.
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
That's a good idea.
@burnhags2572
@burnhags2572 11 месяцев назад
Teq are standup guys Hunter literally contacted me on a Sunday to help me with my lift on a Sunday bro that’s amazing
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Yep, we wholeheartedly agree with you. Hunter and Miles are great dudes and we were very happy to get the chance to work with them. Happy Wrenching!
@phillipblount5541
@phillipblount5541 11 месяцев назад
Prescient video man! Got mine a few weeks ago and was getting ready to install this weekend. Now with the help of my favorite 3rd gen team. Thanks guys!
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Awesome! Have fun with the install.
@Citizenspress
@Citizenspress 11 месяцев назад
thanks timmy the tool man, yesterday i picked up a used set of these headlights for $100 bucks! one of the halos had fallen off and i had to bake them/open them up and remove the halos, the wiring was a rats nest and this really helped me understand how to make heads and tails of it! enjoy the beer, cheers!
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
You got a screaming deal. Nice find! I'm glad our video helped you figure out the wiring.
@richardsauer599
@richardsauer599 11 месяцев назад
Good job Tim! You and Sean have a good thing going. Thanks for sharing!
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Thanks Richard. We do have a good thing going for sure. But, it is a lot of work.
@jamesobriant4655
@jamesobriant4655 11 месяцев назад
What a great video! Thanks for the shout-out! Hope to get you back here for a Toyota visit!
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Thanks Jamie. I definitely need to make it out to Raleigh for another visit.
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
Wow the front halo is so bright it makes the entire headlight glass the color you choose very neet 29:00 @Timmy The Toolman
@mileseubanks5104
@mileseubanks5104 11 месяцев назад
Awesome video guys!
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Thanks MIles. We appreciate your support of our channel.
@aviatorgeek99J
@aviatorgeek99J 10 месяцев назад
I got burned by BxBuilt, waited almost two years to find out the news recently. So I placed an order for a whole new front end, corner lights, headlights and the TRD pro grill. Waited maybe two weeks instead of two years and all the parts arrived well packed. Installed the lights today and am very pleased with the basic rear turbine halo and amber switchbacks, all blacked out which looks great with my black '02 Sport. The turbine halos are a nice match, and resemble a hint of the supercharger hiding under the hood. I had to use the original bulb sockets for the corner lights, these must vary between years. I was concerned with having to cut the daytime running headlight wire (as with BxBuilt) but this was not a problem. The switchbacks even flash with the corner lights now when you lock the truck with your remote. The halos still blink amber with your turn signal with no daytime running! Just the behavior I was looking for. Thank you TEQ Customs and the OG Timmy The Toolman!
@TimmyTheToolman
@TimmyTheToolman 10 месяцев назад
It's great to hear TEQ Customs hooked you up, and you're stoked on your purchase. Thanks for the comment. We appreciate it!
@BJMiguel3
@BJMiguel3 11 месяцев назад
Great video. Now time for me to order one
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Thanks! You'll like them.
@mrboywonder
@mrboywonder 11 месяцев назад
Timely video - I just placed my order with TEQ Customs earlier this week! Thanks, as always, Timmy and Sean!
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
You'll like them. Have fun with the install when you get them.
@williamtsol636
@williamtsol636 11 месяцев назад
I almost called you the other day because I couldn't figure out why my passenger light on the dash would always stay on !! I traced it down to a poor connection on my passenger airbag connection terminals ! I used electrical contact cleaner and solved the problem ! Just a heads up for anybody that might encounter that problem ! Thanks for another good video too !! 👍
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Good job figuring out the issue.
@ever2gut1
@ever2gut1 11 месяцев назад
thats a pretty sicmod, i got the bxbuilt ones some time ago and so far they have held up but i do know that is not the case for everyone else
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Definitely a Sic Mod. Good to hear your BxBuilt headlights are holding up. Like you said, the quality BxBuilt put out wasn't consistent. Glad you got a good set from them. Thanks for commenting.
@DEEPerthantheCUT
@DEEPerthantheCUT 10 месяцев назад
Oh what perfect timing
@TimmyTheToolman
@TimmyTheToolman 10 месяцев назад
Glad we could be of service.
@quillaja
@quillaja 11 месяцев назад
It would also be nice to see the TEQ headlights compared to stock housing with bright LED bulbs which can be had in 4-5k lumen (per set) output for about $60-$70. Naturally "focus" will be different, and you don't get the bling rgb rave lights with the bulb swap.
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
LED Bulbs are garbage. There is no real comparison to projector lenses. Anytime I see someone on the road with LED bulbs installed in their headlights I assume they enjoy blinding people with that obnoxious light output. - Sean
@quillaja
@quillaja 11 месяцев назад
@@TimmyTheToolman I don't disagree that projector lenses provide superior aiming for the bright lights we want in our vehicles these days. However, a poorly aimed projectors are equally blinding. And nothing is going to make a difference if the other driver's eyes are directly in your light's beam, which is often the case with a standard sedan vs truck since a sedan driver sits so much lower compared to even a non-lifted truck's headlights. There's also road geometry to consider. Even in my Tacoma, I sometimes get momentarily blinded by newer sedans with bright projector lights simply because they're going over a slight rise in the road (eg at an intersection) that raises their lights into my eyes.
@christopherbrown5338
@christopherbrown5338 3 месяца назад
One of my screws for adjustment was so rusted I was lucky to get the plastic nut to turn at all. Had to remove it & re-tap to get it to work again.
@TimmyTheToolman
@TimmyTheToolman 3 месяца назад
Was this on a set of TEQ Customs headlights you just purchased?
@christopherbrown5338
@christopherbrown5338 3 месяца назад
@@TimmyTheToolman No, a retro-fit using my old headlight reflector, housing & glass along with a Morimoto projector with HID lights. No Halo's or anything else. I just want to be able to see at night :)
@TimmyTheToolman
@TimmyTheToolman 3 месяца назад
@@christopherbrown5338 Gotcha
@AllTerrainRescue
@AllTerrainRescue 4 месяца назад
Thx Tim
@TimmyTheToolman
@TimmyTheToolman 4 месяца назад
You're welcome
@kdmtmb7657
@kdmtmb7657 8 месяцев назад
Just ordered a set of OEM+ headlights and black glow gauge from TEQ 20% off until end of the month
@TimmyTheToolman
@TimmyTheToolman 8 месяцев назад
Smart move. You'll be happy with them.
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
Just got my Front ifs 8' arb Locker Diff and Rear 3rd Member Arb locker diff From East Coast Gear Supply For My 4th gen and my 97 Ltd 3rd gen Yesterday so excited to install and it started poring Rain 2:35 @Timmy The Toolman
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Have fun with the installs, Antonio.
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
@@TimmyTheToolman thanks Timmy so exited better offroad Gear sicmods
@lookingoodclub
@lookingoodclub 10 месяцев назад
Hey Timmy, and Sean, I love your videos. I watch them all the time I learned a whole bunch. I got a lot of the sicmods you talk about I just got a 333 fabrication Billet clamp that goes to the steering rack. I wonder if you’d be interested in doing a video on this clamp For the third GEN forerunner Thank you kindly.
@TimmyTheToolman
@TimmyTheToolman 10 месяцев назад
Is that just the collar that houses the big bushing on the passenger side?
@xanderman3759
@xanderman3759 10 месяцев назад
One thing I've noticed is that w/the retrofits, no one really centers the projectors inside the housings correctly. The center circle of the lens of the light assembly should be right in the center of the projector lens themselves, this will accurately point the projectors. So both headlight assemblies will have a about an equal amount of adjustment on the backside, adjustment screws will have equal length or threads showing. With the projectors centered correctly in the housings, this will also make sure they are aimed correctly horizontally so your not blinding light in any other direction. So with it centered, it'll project where its supposed to be, yours are both pointed towards the center like eyes both looking at the tip of your nose. Then from there adjust vertically with both top cut offs on the same level, this will not blind on coming drivers, reason they step down on left side for the beam pattern for LHD. And most DO NOT, have a clean cut off line, its always blurry. When you see them done correctly, they have a super clean cut off line with no blurriness, like what your projectors are showing, esp at the 25ft distance. But kudos on TEQ for trying to right the wrongs.
@TimmyTheToolman
@TimmyTheToolman 10 месяцев назад
Roger Dodger. Thanks for the comment.
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
I did the same thing Shuan did Snuck it right behind the radiator Under the Lip were the other truck wire loom is 19:06 @Timmy The Toolman
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
Very nice tight bright blue cutoff line Very awesome 27:08
@jeffspicoli6088
@jeffspicoli6088 5 дней назад
Great video, and as always, Tim, thanks for your content and serving the Toyota community, especially the 3rd gen 4Runner (I have a 96). From your video, it's difficult to tell if the supplied connectors on the harness are waterproof. Will you please comment on that? Thanks again!
@TimmyTheToolman
@TimmyTheToolman 5 дней назад
Hey Jeff, we appreciate your comment about what Sean and I do. As for your question, the connectors aren't waterproof and they don't need to be. I don't think any connector I've seen is waterproof, but some are water resistant. Do they need to be waterproof? Not really. If you submerge your vehicle in deep enough water, a whole host of electrical connectors could be compromised. Under normal conditions, the connectors provided won't be compromised by water intrusion.
@jeffspicoli6088
@jeffspicoli6088 5 дней назад
@@TimmyTheToolman thank you so much for your feedback!!
@TimmyTheToolman
@TimmyTheToolman 4 дня назад
@jeffspicoli6088 You're welcome. I just realized you have Sean Penns's name in Fast Times at Ridfemont High. That movie came out the year I graduated high school, 1983.
@jeffspicoli6088
@jeffspicoli6088 4 дня назад
@@TimmyTheToolman No worries. It's obviously one of my favorite movies, and I was a freshman in HS when it debuted. Again, thanks for your channel and content.
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
Good video Same Wire routing i did On 3 of my rigs over 10 years ago for my Hid Systems front and rear halo's and Demon eyes 16:12 @Timmy The Toolman
@ryanpapa3111
@ryanpapa3111 11 месяцев назад
Do you have a video on your radiator setup? I need to replace mine and would like to upgrade since I am in Texas
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
I just upgraded the radiator in my 98 4runner with a Koyorad Aluminum one. Here's the video of the install: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-4hS0pdMzyLo.htmlsi=Rg3vItLyVJ0oNOLK
@khaos2nd
@khaos2nd 11 месяцев назад
Hey Tim. Speaking of retrofitting, and I’ve had this thought for a minute, but would it be possible to have a 3rd Gen 4Runner 2wd auto selector be the same as the 2wd Tacoma one? I prefer the look of that shifter and I only see that style shifter on 4wd 4Runners. I was thinking it would even open up 2 more cup holder space options also. I know the tacoma and 4Runner bezels aren’t the same when it gets up to the lower dash. Do you think this kind of retrofitting would be possible on a 2wd 3rd gen 4Runner?
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
I'm not sure if that would work. Never heard of anyone doing it.
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
Purple power works amazing for tons of stuff i use it a ton on Greasy floor matts and carpets as well as cleaning engine components and skids 21:09 @Timmy The Toolman
@damacknificent151
@damacknificent151 5 месяцев назад
Hey Timmy, can i just get bare bones basic headlight? I mean no wires or extra stuff to connect. Just plug and play just replace the bulb with something more high output. I dont want all that bling.
@TimmyTheToolman
@TimmyTheToolman 5 месяцев назад
Call TEQ Customs and see if they have a recommendation. I don't know if a good aftermarket replacement bulb to buy for the headlights.
@to4178
@to4178 5 месяцев назад
What happens if i loosen the Left/Right aim adjusting bolt? Does it go left or right?
@TimmyTheToolman
@TimmyTheToolman 5 месяцев назад
As you start adjusting it, you will see where the beam goes. - Sean
@2x776aQ1
@2x776aQ1 6 месяцев назад
Hi Sean - I live near San Jose. When I get mine (1999 4Runner) can you tell me location of where you adjusted the TEQ headlights? I can't find a good flat area with a wall.
@TimmyTheToolman
@TimmyTheToolman 6 месяцев назад
That wall we used was kind of garbage, it had a slight slope to the wall and wasn’t perfectly level.. I think there are better walls out there. That’s the fun of it though, drive around in back delivery alleys, and scope out some spots. - Sean
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
The Trim peice under the headlight is Called the Headlight Valence 8:59 hope that helps @Timmy The Toolman
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Doesn't really help me, but it is good to know what that piece is called. I think chingadera is a good name for it as well.
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
@@TimmyTheToolman there are also several peices on the front bumper called a Valance as well upper and lower.. I know I have lots of Unless Knowledge lol 😆
@AssQuake
@AssQuake 11 месяцев назад
The beams should be stacked, not stepped. Top of the stepped beam should align with the other. The bottom of the step should be aligned with the other. Also the passenger projector is slightly off rotation but it isn't that bad. Just something that should be noted as you want a perfect horizontal rotation to not blind on coming traffic. You can also center the headlights by measuring between the width of the projectors and placing the location on the wall where you marked your horizontal aim line
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Thanks for the feedback. Some have argued it is better to have the driver side headlight a bit lower than the passenger side to be less likely to blind on-coming drivers.
@AssQuake
@AssQuake 11 месяцев назад
Fair enough! Road safety works both ways. As long as we aren't blinding each other im happy! The fact that anyone has access to powerful lighting means they need to be educated in safety for others as well. aiming is important
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
@@AssQuake I wholeheartedly agree with you.
@dc6233
@dc6233 11 месяцев назад
I always found it funny that Toyota uses green wires with small other colored stripes for power. Many people don't know that it's the grounds that are switched, not the hots. This is why people blow fuses... I would have added some shrink tubing on top of those butt connectors.
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
The butt connectors I use are shrink butt connectors. There's no need to put shrink tubing over them. They seal just as good as shrink tubing does. It would be a waste of time to put shrink tubing over them unless it's a looks thing and you want it to be black.
@reaper352c5
@reaper352c5 11 месяцев назад
i am getting the feeling shawn is going to be getting a set for his vehicle in the near future.
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
He already did. I'm guessing you didn't watch the whole video.
@reaper352c5
@reaper352c5 11 месяцев назад
i wasn't able to my daughter needed my attention. @@TimmyTheToolman
@thomasjefferson3552
@thomasjefferson3552 3 месяца назад
Do the new lights draw less voltage from the battery?
@TimmyTheToolman
@TimmyTheToolman 3 месяца назад
Yes
@brandonryder3632
@brandonryder3632 11 месяцев назад
I missed it. Did you get the LED projectors or the HID option?
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Bi-LED
@JJ-rb3ss
@JJ-rb3ss 6 месяцев назад
My bxbuild edging lense became upside down after a year and one of the projector became loose smh
@TimmyTheToolman
@TimmyTheToolman 6 месяцев назад
Yeah, it appears the quality of BxBuilt headlights was very inconsistent.
@MarkamisPrime
@MarkamisPrime 11 месяцев назад
Iiiiiiiiii neeeeeeeeeeeeeeeed iiiiiiiiiit.
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Get your credit card out and getter dun Mark.
@igkok
@igkok 11 месяцев назад
Where did you get your Toyota 4ever shirt?
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
An online seller. Don't remember the company.
@dC5alex
@dC5alex 6 месяцев назад
Great video as always but TEQ Company has horrible customer service. Ordered and never got my set after 8-9 weeks of waiting
@TimmyTheToolman
@TimmyTheToolman 6 месяцев назад
Did you contact them yet to understand your order status? - Sean
@dC5alex
@dC5alex 6 месяцев назад
Yeah they don’t reply back lol They disable their social media comments for a reason.
@TimmyTheToolman
@TimmyTheToolman 6 месяцев назад
@@dC5alex I will contact the owner and get their side of the story.
@TimmyTheToolman
@TimmyTheToolman 6 месяцев назад
I talked with the owner of TEQ Customs, Hunter Gill. The following is his side of the story. The advertised lead time for Alex's set of headlights was 8-10 weeks. At exactly 8 weeks, he filed a chargeback. I checked the email and there have been no emails from Alex. The only message that I see was on the website chat after hours. It appears Alex did not put in his email address as prompted, so our response the next morning was likely not forwarded to him, but he was responded to nonetheless. His headlights were complete, but given the chargeback, they will obviously not be sent out now. For anyone reading this exchange, it's important to understand there's always at least two sides to every story. Alex Pham criticized TEQ Customs for poor customer service, but after reading Hunter's side of the story, I'm having a hard time agreeing with Alex's assessment of the TEQ Customs company. Also, I've met Hunter the owner and Miles his right hand man in person and these are good guys. It's the reason we decided to work with them and promote their business in the first place. The lesson learned is you can't always base your decision on whether to do business with a company from the negative reviews.
@123capk
@123capk 11 месяцев назад
Just don’t buy BX built ones 🤣
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
Well, they are out of business so you couldn't buy a set of their lights anyway. We mention the fact BXbuilt ripped off a whole host of people when they closed shop. Obviously, not everyone has integrity.
@FonzoCapone
@FonzoCapone 23 дня назад
My driver side headlights keeps popping out of its socket on the top right, is there anyway to fix this so it stays snug?
@TimmyTheToolman
@TimmyTheToolman 22 дня назад
Use some Plastic JB Weld on the screw, push into the stripped screw hole, tape it place for a while and you should be good to go.
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
Shame you cant change the color while in the vehicle my morimoto app worls in the cab for my setups but mine are very old Setups 31:18 @Timmy the Toolman
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
It does work for me in my rig with an iPhone. I can adjust it from the drivers seat. - Sean
@AntonioClaudioMichael
@AntonioClaudioMichael 11 месяцев назад
@@TimmyTheToolman got you
@SanDiegoDude619
@SanDiegoDude619 4 месяца назад
I'm curious, Sean, if there is a difference in the mounting location (and orientation) of the controller between your rig and Timmy's. That may be a factor. When I saw the location where Timmy mounted his, I was not entirely surprised at the poor Bluetooth connectivity between his phone (presumably mounted on the dash) and the cavity in front of the battery where his controller sits. Lead and water are *excellent* at blocking Bluetooth radio wave frequencies (~2.4Ghz), and batteries are filled with lead and water. I just received my kit from Teq, including the Bluetooth controller option. I'm going to mount the controller above or behind the battery to see if that addresses any connectivity issues between the controller and my Android phone.
@AntonioClaudioMichael
@AntonioClaudioMichael 4 месяца назад
​@@SanDiegoDude619probably mine is Mounted to the firewall on the driver side really close to the wire grommet never had interference issues ever it works from well over 130 feet away mine is also a 15 year old Morimoto Bluetooth module
Далее
Армия США вошла в Зангезур
04:17
Просмотров 230 тыс.
Engine preparation for the 3.4L 5VZ swap
6:10
Просмотров 20 тыс.
3rd Gen 4Runner Tundra Brake Upgrade
13:15
Просмотров 39 тыс.
5 Things That I Hate About My New $50K Tacoma...
20:31
EXEED VX отзыв владельца #shorts
1:00
Просмотров 3,4 млн
Это самая гигантская машина!
0:26