The best cheap or free Ender 3 upgrades - re-modding my newest version

Подписаться 516 тыс.

Просмотров 288 тыс.

50% 1

The Ender 3 is a fantastic first 3D printer, but it can be made better with these cheap/free upgrades. Most of these are 3D printed and freely available on Thingiverse, and the others are very affordable. In this guide, I revisit the mods I completed on my original Ender 3 and redo the ones that I have been missing on my new Ender 3 Pro.
Purchase the Ender 3 from these links:
Ender 3 Pro Banggood ($30 off with coupon 1d1c08): bit.ly/2OUcEyS
Ender 3 Banggood (US warehouse, Coupon: f2bf59): bit.ly/2Efoi6B
Ender 3 Pro Amazon: amzn.to/2DpkbEs
Ender 3 Amazon: amzn.to/2xyJ23s
Ender 3X (glass bed version): amzn.to/2I7dG85
Assorted M3/M4/M5 nuts and bolts:
Amazon ($16) - amzn.to/2pF4wHx
Bangood ($20) - bit.ly/2zWO3o4
Stepper motor dampers:
Please note that viewers are reporting fixed belt pulleys on the steppers in newer models. Don't order these if you have this.
Amazon 5 stepper dampers for $13:amzn.to/2v5ng63
Banggood $2 each: bit.ly/2NtB010
Capricorn Tubing (plenty of spares of each of these after fitting to the printer):
1m XS PTFE tube on Amazon ($14.50): amzn.to/2wsV2lR
PC4-M6 and PC4-M10 connectors (10 of each for $14): amzn.to/2ykFykM
Micro SD to SD card extender (if you regularly use th SD card): amzn.to/2OP5NHp
Printed parts I would still recommend:
Ender 3 fan guard (not needed for Pro): www.thingiverse.com/thing:293...
LCD PCB cover (a version exists that uses the standard screws): www.thingiverse.com/thing:285...
SD card extended holder (if you regularly use the SD card): www.thingiverse.com/thing:291...
Ender 3 tool tray (if not using a Raspberry pi): www.thingiverse.com/thing:295...
Extruder wheel: www.thingiverse.com/thing:277...
Simple filament guide (lower): www.thingiverse.com/thing:289...
Cable clip: www.thingiverse.com/thing:294...
CR10 extruder knob: www.thingiverse.com/thing:310...
Raspberry Pi case: www.thingiverse.com/thing:301...
Printed parts I don’t think are needed anymore or have better versions:
Z stepper spacer: www.thingiverse.com/thing:292...
Filament guide snap in (up high): www.thingiverse.com/thing:291...
Filament guide (low next to extruder): www.thingiverse.com/thing:289...
Display ribbon cable clip: www.thingiverse.com/thing:288...
Petsfang duct: www.thingiverse.com/thing:275...
Tool tray: www.thingiverse.com/thing:292...
Damping feet: www.thingiverse.com/thing:291...
Anti snag end cap: www.thingiverse.com/thing:294...
End rail cover: www.thingiverse.com/thing:299...
Pi case: www.thingiverse.com/thing:272...
Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: www.x3d.com.au
Gearbest affiliate link (help support the channel): www.gearbest.com/?lkid=13807527
Take a look around and if you like what you see, please subscribe.
Support me on Patreon: / teachingtech
#3dprinting #ender3 #upgrades

Опубликовано:

23 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 223

@srowley85 5 лет назад

I bought an ended 3 just after you started your videos on the model. Thanks for your excellent advice! I look forward to seeing more of what you’ve done to improve the Ender 3.

@havoc010101 5 лет назад

Michael, my ender 3 is on the way! I plan to use some of the upgrades shown in this video. Great video, keep the content coming!

@douglasbollinger8678 5 лет назад

Since I just assembled a new Ender 3 today, this video came at the perfect time supplying 6 small projects to test and eventually enhance the printer. Looking forward to more of your content!

@blackwolfecc 5 лет назад

Great video. Definitely looking forward to the next one! Some of your tips and tricks have helped me eliminate most issues I’ve had with the Ender 3. Thank you and keep up the great videos!

@ajfloats387 5 лет назад

I JUST GOT MY ENDER 3!!!! And your videos are a fantastic guide line for me! Thanks for the videos.

@Drinnan 5 лет назад

Thanks for putting the parts in your description. My pro should be arriving withing the next 12 hours and I'll definitely print these things off once I'm setup

@SidneyCritic 5 лет назад

When my PLA filament guides started humming - like materials don't like rubbing - I came to the same solution of moving the filament reel right to the end as well. I think they fixed the bowden tube by the time I got mine 2 months ago, because I haven't had any problems with the std one.

@TheAlexEffects 5 лет назад

For the LCD Cover there is a version to fit with factory screws on thingiverse ;)

@KnowBuddiesLP 5 лет назад

Ohhhhhh! Do you have the number for that part? Links maybe blocked but can look it up by the # :)

@TheAlexEffects 5 лет назад

@@KnowBuddiesLP actually just realized its the one linked in the description :D Just pick the stl with factory in the name ;)

@pdjames1729 5 лет назад

just in case that wasn't bs... it's thing:2987100 - but you still lazy :P I searched for Ender 3 cover (looked through list for one for stock screws)

@oren88 5 лет назад

Awesome thanks, by the way the original one added that also in a new update: "16.08.2018 added two new closed Versions for factory srews, one with buzzerhole, one without hole." www.thingiverse.com/thing:2858209/

@tonyhopkins4399 3 года назад

Many thanks for your info on the Ender 3 , have been looking at 3D printers for ages anf thanks to your great coverage of the Ender series I now have one and am printing, keep up giving advice.

@richardr3178 5 лет назад

I love all of your videos. Please keep up the great content!

@KnowBuddiesLP 5 лет назад

Lol just did the capricorn tube Friday! Should have waited for the new tutorial, but working now! Keep up the great work and in depth and honest videos!

@KnowBuddiesLP 5 лет назад

Oh! Definitely need the next video, glad you mentioned firmware changes, need to order the pi zero and cables in preparation!

@ThELyNXfragm 5 лет назад

@@KnowBuddiesLP get the full pi the zero is under powered and gave me loads of hassle.

@KnowBuddiesLP 5 лет назад

@@ThELyNXfragm sorry, I meant the ardiono (sp?) I have the pi 3 with OctoPrint setup already, meant for the bootloader setup, thanks for the call out, and couldn't agree more on the 3 vs zero :)

@JWGasner 5 лет назад

Check out the double high Pi case, you can put in a buck converter, split the printer power feed and your set, nice and clean.

@PleiadianStarseed7 5 лет назад

Do you have the link for this?

@McPcholkin 5 лет назад

Thank you for video, waiting for cooling mod test.

@antcri730 4 года назад

A faster easier almost instant way to get a lower filament guard and not use any filament is to cut about an inch of the protective cover that came on the Z lead screw and slip it over the screw to stop any grease swapping. Like Teaching Tech said the simplest solution is often the best.

@MrPvallone 5 лет назад

Great tutorial. Thanks - Keep up the good work. Your videos have helped me about a lot.

@KennethScharf Год назад

I printed on of the filament guides that clip onto the upright part of the extruder plate that holds the roller wheels. It fits kinda loose and I was worried about it falling off, so I glued it in place with a small amount of 5 minute epoxy. If I ever need to remove it I can probably do so destructively, and then peel off whatever remains without damaging the printer. Moving the filament spool holder over to the far left wasn't easy, getting the T nuts into the slot between the screws holding the uprights is a RPITA. I installed a different kind of spool holder. I found a model on thinigiverse for a spool holder insert with stepped sides that will work with various different spool inner diameters. These have two 608zz bearing in them (you need to print two of these, one for each side of the spool). I then printed an adapter to put an 8mm (5/16") carriage bolt in the big hole in the bracket which the spool holders slide onto. A wing nut holds it together. It does take longer to mount the spool on this, but it holds it MUCH better and turns more easily. You can adjust the friction by tightening or loosening the wing nut as required.

@2691014 5 лет назад

Awesome video! My Ender 3 pro just arrived in the mail so this video came just in time. Looking forward to the next one! Thanks for all your help and keep up the great work!

@toyotatrd 4 года назад

Fayiz Mahgoub damn how big is your mailbox

@Hero1117a 5 лет назад

Very good, can't wait to see the bullseye vid

@yesimjeremy 5 лет назад

I've been running the bullseye for about 3 weeks now and really like it. Interested to see what he has to say about it though.

@MyLanista 5 лет назад

Good to hear, do you have better bridges with the bullseye? I tried the vent ring: www.thingiverse.com/thing:2912394 but this didn't work too well.

@avejst 5 лет назад

Thanks for sharing 👍😀 Nice projekt 👍

@axelhopfinger533 5 лет назад

One more small mod i can recommend is a printed knob for the top of the Z axis lead screw. But be wary, some types may collide with a too wide extruder gear knob if printing higher than about 230mm, making rattling and grinding noises and possibly leading to both extruder problems and damaging the lead screw. And one more essential upgrade would be a better spool holder, as the stock one is just pretty bad overall.

@TeachingTech 5 лет назад

Interestingly a lot of people assemble the holder backwards so some rolls of filament don't fit.

@yujenlin1197 3 года назад

for the screw guard i just use a unused shrink wrap that will fit loosely and use that.

@F1fanatic21 3 года назад

Great video, thanks

@mattlogue1300 2 года назад

I put a cable holder for the x motor cable, just a bit of baling wire holds out rubber bands that hold a loose cable tie for it.

@michaelwuchitech7598 5 лет назад

There is a new version of the anti-snag attachment that does not require screws. It clips on to the extrusion

@duality4y 3 года назад

got a link?

@duality4y 3 года назад

@@michaelwuchitech7598 thanks!

@marcosramirez385 5 лет назад

Just want to say thanks for your videos especially those of the Ender 3. I use a Bltouch for bed leveling. Also, Buildtak has a flexplate the size of the bed 235mm² with pei sheets if you want.

@simulatedfish1995 5 лет назад

Sure if you want to buy build plate that is half the cost of the printer. I can't believe it is worth it.

@marcosramirez385 5 лет назад

Alec Ward You can just buy a spring steel sheet and pei and just use clips. That would still be worth it in the long run for large prints. Besides, people are already swapping out the control boards and using tmc drivers with noctua fans, capricorn ptfe tubes, linear rail mods, bltouch, and swapping out the hotend for a microswiss. Whats one little magnetic bed that lets you swap out your surface from buildtak to pei. Not to mention you can use all the build space without your nozzle hitting any clips. Its useful but not entirely necessary. There is no sarcasm in this post. Just pointing out how useful it can be in the long run.

@simulatedfish1995 5 лет назад

@@marcosramirez385 right I just think buildtak is a rip-off due to "name brand" over charging. I just bought a $15 magnet build surface and called it good. Binder clips drive me crazy!

@marcosramirez385 5 лет назад

Alec Ward I did buy the flexplate. It might not be worth it to others but I like it. It gives me the option to print with different materials and up to 120 degrees on the bed. Plus with my fixed heatbed and Bltouch I dont have to worry about leveling. Like I said, not for everyone. Which build surface were you talking about by the way? I'm interested in something cheaper for another Ender 3 I plan to buy which will b a pla only machine.

@TeachingTech 5 лет назад

I have a prusa mk3 with the flexplate, a CCT with the buildrak version, and easy peelsy on two others. They are all better than standard. Personally I like the prusa one the best. Just my 2c.

@macrumpton 5 лет назад

I got my ender3 2 weeks ago and aside from some bird nests and prints that randomly stopped in the middle (both problems fixed by reformatting the sd card). I am astonished at the high quality of the prints (after I found some good default settings and levelled the bed). I am also astonished at how slow 3d printing is. I have a laser cutter and I can make a large very elaborate cut and it rarely takes 30min. That being said I'm loving this machine and the happy song it makes when it's printing. Hopefully this will be the inspiration to finally get over the fusion3d hump and leave TinkerCad behind/

@TeachingTech 5 лет назад

I guess the difference is laser cutting is 2d. You have to extrude the outside perimeter and then the infill, repeating for each layer. Try turning up your base print speed until quality suffers.

@dipt_tpid 5 лет назад

The beeper cover is good, if you don't want to remove it completely.

@Hogarth714 5 лет назад

Great video. Thanks for putting the time and effort into helping us all out. I thought you said in a previous Ender 3 video that you had successfully tested it with different filament materials including PC. If this is true would it be possible to get your machine profile you use to print with PC? Thanks mate.

@abs358 5 лет назад

Vid on 3d printed belt tensioners for the ender 3

@vitosentosa1690 5 лет назад

Make video about change filament with coldpull VS hotpull 😁

@punitproduction 5 лет назад

Thank you for your videos. Ender 3 is printing its first benchy and all is well. Added quite a few upgrades. Here is my question: Have you considered extending the height of the ender 3 with taller rails if that is even possible? Thank you.

@corpgiroro333 5 лет назад

Also; as far as i can tell the z axis motor is held in the same way as the updated Ender 3 non-pro.

@TeachingTech 5 лет назад

Agreed.

@itsmeintorrespain2714 5 лет назад

I shimmed mine with some folded paper strips. Didn't realize that there was some adjustment available within the mounting system. (Ender 3 "Mk 2".)

@aeixnx 5 лет назад

Anyone care to recommend a good place to mount the pi cam for timelapse recording ? I've seen some 3D printed mounts that mount on the printer. Wondering if that is optimal.

@genemaster74 11 месяцев назад

This is great i just got 2 ender 3's and having access to this Info is so handy m8......now ive got to source a 422 or 427 board, i think...one of the printers has a green board, which is not plug and play as ive found out. Im 50yr ol with disabilitys and these newer models are more user friendly.😀

@dylmey 5 лет назад

My ender 3 came with a really bad dip in the center of the bed, can't wait for the video to do mesh leveling without a sensor.

@TeachingTech 5 лет назад

Will be the next video out.

@jw200 5 лет назад

Waiting for the videos about bed leveling and other things you said

@TeachingTech 5 лет назад

Bed levelling is the next video. Out in the next 24 hours.

@Foxy_proxy 3 года назад

Could do with a vid on all your latest ender mods

@williambye3894 4 года назад

If like to know more about the set up of the raspberry PI.

@pr0xZen 3 года назад

A couple of little adjustments I would consider in 2021. ° Don't grind down the bed adjuster, print a smaller one. ° If you have a Pi 4, don't do a completely or near sealed plastic case. It needs cooling, or at the very least free access to ambient air for convection. ° If you do tall prints, or frankly in general - if you have the space, consider moving your filament holder off the printer. Or at least to a mount on the bottom frame.

@perfectentrytrading 5 лет назад

The bowden tube set up would be much better if it was a olive fitting instead of a press in thing

@TheSentientCloud 5 лет назад

Oh thank God you're gonna do a beginner Ender 3 video. My x axis bar seems to be... off or something. The little fan for the extruder gave out and started buzzing (if you know a solution please let me know) and the bed seems to be unusually difficult to level.

@TeachingTech 5 лет назад

I've finished recording it and just have to edit. It should the issues you describe.

@TheSentientCloud 5 лет назад

@@TeachingTech oh awesome, I'll keep an eye out! Really want this thing to be printing like I keep seeing others printing with them lol

@BryanMcKibbin 5 лет назад

Interesting you mentioned the part cooling fan failure. Mine has just started groaning intermittently which usually means it is on its way out.

@lachmaart4064 4 года назад

a spool bearing system is a MUST for that printer, you haven't mention it in any of your videos (at least those I watched)

@michaeldsilva6583 5 лет назад

Mate, if you have the time compare bullseye with something completely overkill just to see how far we can push this thing. Also any thoughts about converting this to a three point mount vs the stock 4? Might make it easy to level the bed. Thanks for all the ender 3 advice!! Cheers!

@TeachingTech 5 лет назад

My next planned video is a bullseye vs stock vs simple ring fan add on. I've designed a cooling torture test and am currently printing a bunch.

@jeremyowen1 Год назад

Got my Ender 3-Pro a month or so ago as my intro to 3D printing and its not really the same machine anymore. I'd say the biggest upgrades in order were a BTT SKR Mini E3 V3 mainboard, Hotend/part cooling fan mount (printed the CR-10/Ender 3 Dual 40mm Fan Ducinator remix with BLT mount), BLTouch/ABL probe, Capricorn bowden, bed spring upgrade and an all metal dual gear extruder. I also bought a glass build plate but 3/10 would not recommend. I'll probably get a PEI plate with spring steel. Some other nice things to have include Vslot Covers, Front LCD panel cover, side mounted spool holder, tool holder/s and there's a few really sweet drawer designs. What do you guys think, direct drive with linear rails next?

@dragoneatingpixels2750 5 лет назад

Looking forward to the bullseye comparison! Maybe you can also do a comparison of the Petsfang vs Circular Cooling duct (theres a lot on thingiverse in case you dont know what that is) vs the Bullseye vs the stock :)

@dragoneatingpixels2750 5 лет назад

Personally, i am still deciding whether or not the Petsfang is worth it to go through the trouble of buying another fan, or if I should just use the Bullseye

@TeachingTech 5 лет назад

That would be good, I'll see how I go for time.

@ABentPaperclip 5 лет назад

Same, I'd love to see a comparison since the bullseye v2 looks like a huge pain since it has so many pieces and it's so modular. I'd rather not waste a ton of time and filament if it's just a flashy looking gigantic fan shroud.

@dragoneatingpixels2750 5 лет назад

@Teaching Tech Thanks for making a video! I'll look forward to it no matter what you end up including :)

@dragoneatingpixels2750 5 лет назад

@eldeecg My thoughts exactly. I'm rather lazy and my printer currently works fine as it is, but if there's like a huge improvement, I think I'd be willing to go through the trouble of upgrading

@lovepinguinlove 5 лет назад

Hi, nice video, thanks. But I've a question about connecting the raspberry pi. I dont see the usb cable for the printer in your video. It is not nice to have all your cables in front of your printer, so I have my rasp. behind my printer. I can't see your becaurse of the high camera view

@TeachingTech 5 лет назад

It's highly possible that I simply had it disconnected while filming. The cable management with so many printers in my room is ridiculous.

@richardroach7670 2 года назад

Do you have a video on the LCD controls axes temperature, extruded etc? I’m confused about all the choices.

@xxxmaddoxxxx 5 лет назад

Is it possible to use the 32 bit smoothie board on an original ender 3 ?

@ChristopherPBacon1 5 лет назад

I tried printing a fan guard. Didn’t go very well... I’ll have to try again

@mikem8145 5 лет назад

Hi, would you have a cheaper option (maybe on BangGood) for the PTFE tube connectors?

@TeachingTech 5 лет назад

As long as they have metal teeth instead of the plastic ones I showed in one of my videos it will be an improvement.

@Viking_Kong 5 лет назад

The spacers for the Z axis stepper isn't necessary. The reason for this problem is that the bracket that the extruder is mounted on and the lead screw goes through isn't bent at a 90 degree angle. If you use a machinist square and get that bracket bent to 90 degrees, you'll find that the spacers are no longer needed.

@TeachingTech 5 лет назад

Thanks for sharing.

@brunodelucena7718 5 лет назад

Hi Michael, I have a Ender 3 and a friend my too, he told me to turn off the extruder fan to printing using ABS. So that is realy bether way to printing in ABS? So my question is, It's safe do that? As i know the extruder is turn on in parallel with the fan board and if i turn that off Can I burn my Ender 3 board? By the way, It's possible turn on the fan board directly on 24v output from the power suply?

@TeachingTech 5 лет назад

The extruder cooling fan must stay on to prevent damage and clogs. The part cooling fan should be off for ABS, except for bridging and overhangs. Hopefully this is where the confusion is.

@ishatraihanjamil7820 5 лет назад

A video for ender 3 octalapse settings please 😄

@TeachingTech 5 лет назад

Coming..

@dleland71 3 года назад

Re: the filament guide... I just put the long back tube that the Z-screw came in back on and it keeps the filament clean.

@MrBerjoska 5 лет назад

Az izzószálakat egy horgászpálcával kezelt porcelángyűrűvel helyeztem. 2mm-es belső méretet vásárolhat a horgászboltban. Ragasztam a filemant a bemeneti üreghez egy erős kétrétegű ragasztóval. (Google Fordító)

@szoke8 5 лет назад

Its in hungarian.

@JoeGaz 5 лет назад

Do you think it is worth installing the petsfang duct? I got a bl touch to use with it too.

@TeachingTech 5 лет назад

With the standard fan, use the bullseye or hero me. If you are upgrading to a larger 5015 blower, then yes.

@jameseliot1134 4 года назад

Is the y axis a must? I’m just scared as I’ve heard the frying your printer part

@fullchakaraninja 3 года назад

How can you tell the difference in the different versions? I have an Ender 3 Pro but some newer videos state they may have thermal runaway protection.

@vastator 5 лет назад

What Y adapter did you use, on thingverse, to be able to install the damper?

@heXor21 5 лет назад

How do you think about changing the bed level springs? My Ender 3 pro just arrived and I have troubles with bed leveling since it changes after every print, as the bed level knobs are spinning really easily = /

@sittingduckize 2 года назад

Easiest solution is to tighten all the knobs (lower the plate) and then re-level with the knobs done up more tightly. It simply sounds like your plate is too high and thus the springs aren't actually pushing against anything and thus the knobs spin freely. When the plate is lowered enough, the springs will be compressed and the knobs will stiffen up.

@summerswoodworking 4 года назад

I just bult my Ender 3 Pro. The slicer software on the TF card is unable to install. Do you know where I can get the software or how to install this one? It has a .msi extension.

@celestialbeas9214 3 года назад

thoughts on linear rails or direct drive for this printer?

@StuGuz10 5 лет назад

Is there any chance u could do a profile tutorial so we can print supper good because my prints suck like no I’m serious they suck

@TeachingTech 5 лет назад

This is the video you are looking for: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3yIebnVjADM.html

@Bowtie41 4 года назад

Banggood Ender 3 Pro coupon expired?!?

@jennymay3085 3 года назад

which pkg of nuts and bolts were they round head or were they hex head

@mwright154 4 года назад

I'm a little late to the game here, Just got an Ender 3 Pro, for Printed Parts you don't think are needed anymore or have better versions. can you list which ones are not needed and which have a better version or link to the better version

@crunchyrobotchicken8134 4 года назад

Hows the bullseye instead of the petsfang?

@thegrafxguy1 5 лет назад

Coupon code for the pro doesn't work for me. Says it's only for specific items?

@TeachingTech 5 лет назад

It might have now expired. I'll update if I get a new one.

@cdevidal 5 лет назад

Newbie here. How do you recommend picking up and moving the unit around? Do you grab it by the top or sides or base or is it not recommended to move it around much?

@TeachingTech 5 лет назад

Worse case is you bump your bed and need to relevel. I don't move it often, but when I do I grab it by the top horizontal frame.

@anantkhanna4954 4 года назад

My ender 3 always stops extruding randomly, I changed the ptfe tube, and it didn't help, I also tried to take the filement out, but it didnt work, do you know why?

@DymoPolska 4 года назад

Plastic extruder? Swap for metal one

@jeffdeprey6279 4 года назад

I have an issue where my raspberry pi send power back to my ender 3 via the USB port. When the Ender 3 is off the Pi will alarm about the power, and the Ender 3 display and fan will still be running powered by the USB of the PI. To me that all sounds like a really bad thing, so I have not been using my Pi with my Ender 3 at all, and that kind of sucks.

@gs42816 5 лет назад

Hi, I'm interested in buying a 3d printer for my grandson, I'd like to keep the cost down to under £350 or so. Can you recommend a printer that is simple to set up and produces good quality prints. Low powered would be great as well as a large bed, self leveling if possible. Thanks, Graham. By the way, your videos are the best, keep it going please.

@ras862 4 года назад

I'm probably waaay to late, but with a Ender 3 pro you can't go wrong! It's the best printer under 300$

@nledevil 5 лет назад

why not print the lcd cover that uses the stock screws?

@TeachingTech 5 лет назад

I printed the version I still had downloaded from last time. It might have been updated or maybe I missed it but I'll update the description.

@felixthecrazy 5 лет назад

I moved my Pi case, like your first one, under the control screen. That way you have fewer wires facing out and no footprint issues.

@TeachingTech 5 лет назад

That's a nice solution.

@WeAreSoPredictable 5 лет назад

Thanks for yet another great video. _But can you (or anybody) help with where I can actually buy genuine Capricorn tubing in, or shipped to, Australia?_ Amazon tells me, _"We are unable to ship non-digital items from __amazon.com__ to Australian shipping addresses,"_ when I try to buy the Capricorn tubing and connectors. Amazon Australia doesn't have the Capricorn tubing, and they seem to have is Teflon Bowden tubing made by PoPprinter, who I've never heard of.

@TeachingTech 5 лет назад

I ordered straight from their website. Shipping costs are annoying.

@WeAreSoPredictable 5 лет назад

Thanks a lot for the response. Convenient that they also sell couplings. :)

@dylmey 5 лет назад

Might be off topic but what is your opinion on adding an external mosfet for heated bed? $10 cad on amazon worth it or is the risk of board damage low on ended 3’s. Assuming 1 year warranty is it worth waiting out the warranty period?

@TeachingTech 5 лет назад

I've heard of a few busted bed MOSFETS where the heater is permanently on. All of the Ender 3s in the wild and the small number of failures might imply that the current mosfets are up to spec, however.

@MrSlowestD16 4 года назад

So you you mention some differences between the Pro and not. Do you think the Pro is worth the $50 as a starting point? I feel like if you want to upgrade to linear bearings it's not worth it, but if you don't intend to do that upgrade, it's not. Thoughts?

@MarkRouleau 5 лет назад

Can you show all of the physical connections to the Pi? how its powered and where its plugged in on the printer.

@corpgiroro333 5 лет назад

5V/3A power supply, connected by the usb mini-b port.

@TeachingTech 5 лет назад

This and then USB from pi to printer mainboard. Plug in USB webcam if desired.

@MarkRouleau 5 лет назад

so you aren't running it from the Ender powersupply?

@TeachingTech 5 лет назад

No but I will be covering that scenario in the future. Still ordering and trialling parts.

@Nekotamer 4 года назад

so should i grease my zrod ?

@pawesteller7833 5 лет назад

Can u tell me what screws i need use for this motor dampners i ordered them through amazon but i dont get any screws :|

@TeachingTech 5 лет назад

Normally you can use the standard screws. Sometimes they are too long. You want M3 x 6 or 8 mm.

@pawesteller7833 5 лет назад

thx

@selectha 5 лет назад

Are the TL-smoother still worth it with the ender 3 pro? Is it the same mainboard?

@TeachingTech 5 лет назад

Same mainboard. I haven't bothered fitting them because it is subtle and I had no good result when testing on the standard Ender 3. Others had more success however, it is strange.

@SteinerSE 5 лет назад

Oh, and while at it, what model is the newer Meanwell PSU? (supposedly better and safer) (might want one if I get the original Ender 3)

@TeachingTech 5 лет назад

Please see pinned post, it has the details.

@SteinerSE 5 лет назад

@@TeachingTech Hmm, sorry, but what pinned post? Do you mean the video info field?

@TeachingTech 5 лет назад

@@SteinerSE sorry, I mixed up which video this was replying to. See the description here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-TAUWlJt2Hmg.html

@koringer 5 лет назад

are the upgrades the same for the pro and the X please? thx!

@TeachingTech 5 лет назад

Read the description, what you want is there.

@SteinerSE 5 лет назад

I'm considering getting a Ender 3 as my first ever 3D printer (som completely green to all this). Would you suggest to get the original version or Pro? do you now have to turn the printer over when working on the PCB for upgrades (as the box is reversed to the original and I assume the cover is now on the underside) ? For me it will mainly be a hobby project to tinker with the printer itself and upgrade it as well as printing minis for board games.

@TeachingTech 5 лет назад

Ender 3 is perfect for your needs from what you describe. Just remember there is a learning curve and lots of support available in forums and groups. I'd recommend my beginner video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-mAU7cIZ0Hns.html Turning it upside down is a PITA. I think 99% of people would be happy with the standard over Pro, so I would go with that.

@SteinerSE 5 лет назад

@David Yeah, got my standard Ender 3 yesterday, already modded ita bit ;)

@billsolomon1 5 лет назад

What is your opinion of the Alfawise U20? I know it is not open source. But by the reivews, it is a really great printer?

@TeachingTech 5 лет назад

Not that one but I have my first Alfawise in the mail to review. Will form a better impression after that.

@billsolomon1 5 лет назад

What version of the Alfawise do you have coming? My printer choice will probably be the Creality 3D Ender3. But if money is good, I will get the pro version. If money is low, I will have to settle for the lesser version!🤔🤔 Thank you for the reply!

@stolz5573 5 лет назад

Hi Michael, On the Creality webpage for the Ender 3 Pro it shows a picture of the Mean Well power supply to be a model RSP-500-24 which is 21 amps and 500 Watts. What I got with my Ender 3 Pro was a Mean Well model LRS-350-24 which is 14.6 amps and 350 watts. Could you kindly check and see which power supply came with your Ender 3 Pro. Also, is a 350 watt power supply sufficient for this printer or does it need to be more like the 500 watt power supply shown on the creality webpage? Any thoughts on this? Thank you for all of the wonderful content that you provide. Your teaching style is excellent!

@TeachingTech 5 лет назад

I have recently checked and it has the 250. Pretty shady on Creality's part.

@benthillerup 5 лет назад

Why would you have an extruder wheel?

@TeachingTech 5 лет назад

It helps load and unload filament, plus serves as a visual indicator of extruder movement while printing.

@toddd.8496 5 лет назад

There is some sort of odd satisfaction watching that little gear turn.

@unhhh 5 лет назад

The simplest solution for the wires is to route them under the unit.

@georgepeoples1209 5 лет назад

coupon code not working

@MrKenlong 5 лет назад

Hi Michael, made most up grades. My Ender 3 is working. Ok I'm using Cura 15.04.2 every time it open it wants me to use the up grade Cura. So what do i do?

@AlanGonzalez-om4rr 5 лет назад

Maybe upgrade it?

@TeachingTech 5 лет назад

If you don't want to upgrade there may be an option to turn off update checking in the settings.

@MrKenlong 5 лет назад

Could not turn it off Was told to use Cura 15.04.2 when i tried mimi , will it work better to upgrade ?

@Mephiston 5 лет назад

why would you not upgrade to a later version of cura? I;m just wondering what would make you decide a later version of a program is a bad thing or not advised?

@YanBousquet 2 года назад

What do you recommend for bolt kit?

@YanBousquet 2 года назад

Sorry for the comment you got it down in the description

@AllInnerLove 4 года назад

Are you using an ender 3 pro?

@parker1ray 4 года назад

I can not see the purpose in Raspberry Pie. you still need to clean the bed, insert filament, start the print and do a bed level. That requires you to be in front of the printer. It's very simple to save to an SD card and pop it in. I also like the fact that I can save hundreds of STL files on an SD card as a portable library.

@raygilfillan 4 года назад

Ray Parker Raspberry pi is one of the best things, most of the things you mentioned you would already have set up for the next print, bed levelling would be taking care of with ABL or mesh, you don’t have to go anywhere near your Printer to start your print, you also have the ability to use a cam to monitor your print from anywhere and there is a multitude of apps available for iPhone and android to give you full control, its genius.

@parker1ray 4 года назад

@@raygilfillan Different strokes. I have video, and remote shutdown. I prefer to be there to monitor and adjust as needed.

@kkuenzel56 5 лет назад

So given a choice, which printer would you rather have. The Ender 3 or the CR10 Mini and why. I have the Mini and love it. I have a friend who wants to get into 3d printing and wondering which one to recommend.

@TeachingTech 5 лет назад

I haven't used the cr10 mini so cannot comment, but people who have both say that they prefer the mini. It has more features and more price, correct?

@TeachingTech 5 лет назад

I haven't used the cr10 mini so cannot comment, but people who have both say that they prefer the mini. It has more features and more price, correct?

@kkuenzel56 5 лет назад

@@TeachingTech Except for the option to add the auto bed leveling feature, I think the mini is a better deal (personally) It's almost fully assembled, larger build area etc. But like the Ender, I have printed many enhancements for my mini.

@Pa55ion 5 лет назад

Hi TT Amazon .com will not ship to Australia. Banggood Coupon doesn't work. Do you have any links for GB with a coupon

@TeachingTech 5 лет назад

I don't sorry, I find them much harder to deal with. I'll update if I come across a new code.

@TeachingTech 5 лет назад

I've just emailed BG to see if they can help.

@TeachingTech 5 лет назад

Here is a new coupon for the Pro: bit.ly/2OUcEyS （$30 OFF Coupon:1d1c08）

@Pa55ion 5 лет назад

@@TeachingTech Thanks Michael will give it a try

@Magic3DPrinting 5 лет назад

You never mentioned why you are now suggesting Capricorn tubing. When I suggested it to you in an earlier video you didn’t seem to agree.

@TeachingTech 5 лет назад

If I recall that was a discussion over using it as a substitute for high temps over an all metal hot end. This is the second video I've made on cap tubing for the Ender 3. The reason I suggest it is to address the many people who had issues with poor quality fittings and tube when the printer first came out.

@kernowcoinringscornishcoin3999 5 лет назад

Hi I’ve just ordered the Ender 3 pro printer doI need a computer to use the printer I’ve only used and got apple iPad can this be used to print on the printer Regards Paul

@christopherirazat8250 5 лет назад

No, you will need a computer, unfortunately.

@shaunwhiteley3544 5 лет назад

Excellent, thank you, I’ve not modded mine much but will after seeing this! Could you please share your fff profile for Simplifi3d for PLA? Cheers

@TeachingTech 5 лет назад

I have a video on tuning slicing software, it is linked to thingiverse in the description.

@shaunwhiteley3544 5 лет назад

Teaching Tech . Thanks, I will have a look. Glad you said it’s on Thingiverse and not the spyware of Facebook. Cheers

@rodsnyder6020 5 лет назад

Hey Michael, the imho best filament guide period is this one: www.thingiverse.com/thing:2456930 You can make the inserted PTFE Tube a bit longer for the filament to be fed in a more convenient angle. You can still use your extruder knob. Drill a hole in the top section of the cover and you're good to go. I use this combination on both my CR 10 and Ender 2. The filament guide you have installed will not protect your printers feeding hole. Over time the filament will grind down your extrunder lever on the top side of the feeding hole. It is constantly grinding on it when feeding filament in. The best solution is a PTFE tube to guide the Filament. Like your Videos a lot. Cheers.

@TeachingTech 5 лет назад

Good points, thanks for sharing.

@corpgiroro333 5 лет назад

Why not cable chains?

@TeachingTech 5 лет назад

Some people hate them, I don't mind them. Just don't think there is a huge need here. Each to their own.

@pdjames1729 5 лет назад

they increase inertial drag on the cables substantially. You want slow printer, increased resonance shudder, lousy jerk so worse ghosting? Add Weight xxPD

@corpgiroro333 5 лет назад

@@pdjames1729 I have not seen any of that on my printer.

@pdjames1729 5 лет назад

Plus, this is a home unit... cable chains on a quarter million pound robot router make some kind of sense... on a magic shoebox? It's posey, wasteful nonsense xx

@pdjames1729 5 лет назад

performance test it against one without chains... you're losing mm/s and detail at speed - but if you like em, keep them. It's Your machine, build it how you want it xx