The Best LED Headlight

Подписаться 6 тыс.

Просмотров 3,6 тыс.

50% 1

This is the best LED headlight that I have found for a moped. I use this on most of my mopeds and love it. Its 12v and works best with a battery or a capacitor to keep it from flickering at low RPMs.
If you dont have a 12V system here is a video on how to upgrade your points system easily
• 12V upgrade and comple...
I buy them in 2 packs from amazon. Maybe you can share with a friend or upgrade two bikes.
This is the headlight - amzn.to/3VGUWnf
This is the anti flicker cap (9006 / 9005 / 9012 / H10) - amzn.to/3IxAWtV
#Moped #DIY #Cornped
My Gear Links
Main Camera amzn.to/3qw1Cnt
Main Lens amzn.to/3qsSOPf
Wide Lens amzn.to/3pwmOdQ
Portrait lens amzn.to/32ooNbv
Mic amzn.to/3HgkBch
Light amzn.to/3qw2SXJ
360 Camera amzn.to/3euCkjV
Selfie stick amzn.to/3pxJGJK

Опубликовано:

5 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 73

@thomaspeffer3885 Год назад

This headlight is sick!!! After following your simple instructions the install was plug and play. Now I can see and be seen when brapping at night. Best of all it fit perfectly into the stock cev bucket on my kitted 1978 Puch Newport. The top cutoff is also a nice bonus. Thanks bro this vid is the bees knees

@Corn-ped Год назад

Haha. Thanks man!

@patrickstover8766 2 года назад

This is perfect, thank you! I bet it wouldn't be too difficult to use the same capacitor for LED taillights if you're using a single wire for all of your lighting.

@Corn-ped 2 года назад

exactly. . .

@CH00SEDEATH 2 года назад

Just did this conversation but got the light with the halo (just connected the yellow to the red) and holy cow is this shit awesome ! Thanx as always for the info!

@lancelloyd7429 Год назад

I received the halo one as well.(Six months ago but actually just realized it last night when I took it out of the box and mounted it in the ring lol). So the yellow wire is just for the halo? If I connect both red and yellow to positive before the cap will it power both at the same time? Or do I need to choose between one or the other? Haha.

@Corn-ped Год назад

Yo should be able to power both at the same time.

@lancelloyd7429 Год назад

@@Corn-ped Awesome. Thank you!

@danieljamespitard Год назад

Hey I could use some advice on this set up. My housing is totally different and was hoping I could run this. I’m upgrading to a CDI kit from treatland. I guess I need a different housing, any leads on that one would be great.

@Corn-ped Год назад

@@danieljamespitard I use this one and treats is having a 15% sale right now with code daggers . www.treatland.tv/BLACK-GUIA-headlight-with-chrome-rim-5-p/guia-headlight-black-025.htm

@ink_stain525 2 года назад

I’ve got this one but I still like the tractor one you used before!

@Corn-ped 2 года назад

I used the tractor one and liked it, but it was a flood light and I didnt like that it was blinding other drivers.

@chadtufts6320 2 года назад

Sweet!!! I've been using extra lights mounted on a balance bar. I'm getting these!!

@Corn-ped 2 года назад

thats cool. I use to have an aux mtn bike light that I would use at night.

@AlexanderLanderman 2 года назад

Oh, this is sick! I'm also curious about a 6V AC current setup. I've tossed a regulator and rectifier in and had good results but your headlight looks nicer than what I have.

@Corn-ped 2 года назад

Yeah I think it would flicker with 6v.

@bjf10 2 года назад

@@Corn-ped mine barely turned on at 6VDC

@Corn-ped 2 года назад

Yeah... Gotta get that 12v POWWA!

@emmanuelnikhil2582 6 месяцев назад

And mainly can we use this lights on moped bikes which does not hav battery in it... Pls do reply

@Corn-ped 2 года назад

This set up works best on a 12v set up. With either a floating ground or a battery system. I have run it on 12v non floating grounds and been fine but there has been a small flicker at low idle. If you dont have a 12V system here is a video on how to upgrade your points system easily ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-007ng5QLEC.html

@frankentrooper 2 года назад

Great video! It would also be great to see how you wired this in. Cheers!!

@Corn-ped 2 года назад

yeah Ill be making a wiring video for this bike.

@midnightvampire49321 2 года назад

Do you ground one wire and power the other then?

@Corn-ped 2 года назад

@@midnightvampire49321 yeah. I ground the black wire and power the red one.

@midnightvampire49321 2 года назад

@@Corn-ped Awesome. Noted. I bought what you linked so im going to try it on my maxi and murray.

@villanautomotive1528 Год назад

Just order it for my newport

@rootstowingsyogahealingnew2101 2 года назад

converting a 77 5 wire and 79 6 wire maxi from 6v to 12v. running points. three questions: got the treats 12v upgrade party and assuming all i need to do is replace the 12v light coil and run it thru the regulator and i'm good to go. also assuming i can swap the jeep fog light you used for my existing bucket and bypass the need to mess with my old bucket and 12v bulbs, correct? do i need a separate regulator to run LED tail and do you have recommendation? i plan to keep my brake light. i'm an electrical idiot and don't fully grasp the terms capacitor, regulator, rectifier, floating grounds..

@Corn-ped 2 года назад

Replace the coil with the treats 12v coil. Then run that thru the regulator and power all of your lights from that. You can put the LED fog light into the stock CEV bucket.

@emmanuelnikhil2582 6 месяцев назад

Does this moped bike hav battery to support this led lights ?

@Corn-ped 6 месяцев назад

This does NOT have a battery. It is just a regulator/rectifier.

@715OLDYORK 2 года назад

Is that bike running on a 12v ac system with just a regulator for lights? or are you running a 12v dc regulator/rectifer on the lighting circuit? just wondering if the antiflicker cap will work on AC since it's usually hooked up to car DC battery setups

@Corn-ped 2 года назад

I m running it on multiple 12v AC regulated bikes and its been great.

@midnightvampire49321 2 года назад

Any ideas or help with where to hide the capacitor? Maybe clip the red and black and extend them and hide it under a seat ya think?

@Corn-ped 2 года назад

Yeah that would totally work. I have hidden mine in side covers, behind headlight faring, and even in a bullet headlight.

@midnightvampire49321 2 года назад

@@Corn-ped it fit in a bullet?

@midnightvampire49321 2 года назад

Im a little stuck if you could lend some advice? I swapped the 6v coil to a 12v like your other vid. I then ran the coil wire to the trailtech, grounded the brown and mated the yellow to the coil. My question is how I should connect the taillight and headlight same as this setup here to be always on. Can i just tap it in to both leads from each light and just ground them?

@Corn-ped 2 года назад

Yes. You should be able to just connect them to your trail tech

@DaBaltimoron 2 года назад

Do you need a rectifier with these?

@Corn-ped 2 года назад

you should use one for longer life. But I have dont it without

@DaBaltimoron 2 года назад

How does this connect to the existing wiring?

@Corn-ped 2 года назад

It wired into the existing headlight circuit

@johnzona1454 2 года назад

Would this work with a stock 6v set up?

@bjf10 2 года назад

Not directly, but you can use an ac/dc converter that will boost the voltage.

@bjf10 2 года назад

Note not any converter will do this, you need a switching one capable of boosting the voltage.

@Corn-ped 2 года назад

yeah its going to flicker a lot on a 6v system. A 12v system would be the best.

@lassebeckmouritsen7425 2 года назад

@@Corn-ped but would you still need to add a regulator? Think I heard that you need to use a regulator everytime u switch to LED lights, but I'm not that well known in this electric stuff.

@bjf10 2 года назад

@@Corn-ped a 6v system will work just fine if you step up the voltage. There's a thread on MA where someone did this on a 6v QT50 with a module like the one I shared.

@Moped_Moproblems Год назад

Do you know if this would work for my targa lx 09?

@Corn-ped Год назад

yeah it absolutely would!

@DaBaltimoron 2 года назад

Okay, but how do you power the headlight?

@Corn-ped 2 года назад

You are going to want nice 12v DC power. If you have a 12v ignition you can do it with a rectifier and regulator. If you have a 6v system, you will have to upgrade your lighting coil to 12v.

@DaBaltimoron 2 года назад

@@Corn-ped uh...so what wire goes where?

@Corn-ped 2 года назад

red goes to positive and black goes to negative.

@TheNkuebelbeck 2 года назад

I just upgraded to this light. I needed to make a spacer as the led was too small

@Corn-ped 2 года назад

what kind of spacer? What headlight bucket are you running?

@TheNkuebelbeck 2 года назад

@@Corn-ped puch magnum. I linked a photo gallery. The headlight fell thru without it.

@Corn-ped 2 года назад

@@TheNkuebelbeck Weird. Maybe youtube deleted the link.

@TheNkuebelbeck 2 года назад

@@Corn-ped it sure did

@bjf10 2 года назад

@@Corn-ped looks like it deleted my post with a link to the ac/dc converter I use with these headlights too.

@mihalypazar4699 2 года назад

This did not fit my magnum out of the box, for magnum owners go to Napa and get a trailer tail light 4” grommets fits like a glove after, some minor trimming of the rubber required

@Corn-ped 2 года назад

thats odd. do you have a stock gia headlight?

@danieljamespitard Год назад

I got a treatland generic moped headlight lens and am having the same issue. Going to get a grommet tomorrow.

@Corn-ped Год назад

The generic plastic bucket does not work. You need the puch style one.

@danieljamespitard Год назад

@@Corn-ped do you have a link to the specific one you are referring to?

@Corn-ped Год назад

@@danieljamespitard I use this onewww.treatland.tv/BLACK-GUIA-headlight-with-chrome-rim-5-p/guia-headlight-black-025.htm

@pedals4show764 Год назад

Puch E50 moped turn signals - NO BATTERY REQUIRED installation part 1 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Gx_idraAa5s.html LED head & tail lights plus led turn signals NO BATTERY