The BEST Toyota 4Runner Interior LED Install Guide (2014-Current) VLEDS 

This is the best explanation on RU-vid. Just installed mine, thanks!

Excellent video. So helpful. I could not figure out how to pull the old map light bulbs out until I watched your video. I ended up using a small piece of duct tape as it was stickier. I just replaced all my interior bulbs on my 2016 4Runner after watching this video and it was so easy following your demonstration. The hardest part for this 67 year old woman was getting down on the ground and back up after replacing the door bulbs! 🙂

Great instruction video. I had a kit but was worried about how to open all the covers safely. This video was a huge help. Thanks.

Well done video. I used the universal tool to take out map lights, duct tape. I had trouble with putting in the dome light bulb , the metal tips kept slipping on the contacts. I used a small needle nose pliers with a gentle touch and it went straight on!

You're a great teacher!! You saved me lots of headaches this morning on my 2023 Limited 😁! Yes, they still have all incandescent bulbs 🙄, except for the glove box, foot wells and door handles. I did have to resort to using pliers on the map light bulbs though, my sausage fingers could not get the tape deep enough around the bulbs. All came out great though! Thank you! 👍👍

Exactly what I needed. Thanks

I did mine a couple months back. I wish I would have stumbled on this video then. I got it done with no issues but this is a very good video, and explained VERY WELL, and in detail.

Definitely appreciate this video. This was a lot less frustrating to install with your help.

This is The BEST 4Runner Interior LED Install Guide , Thanks!

great tutorial man...thorough enough to keep me from breaking things in the process, and helpful in identifying which bulb goes where.

This was very helpful. Especially the map lights. Suckers were in there tight as heck. Much appreciated!

If you pop out the multi terrain selection area there are two screws that will let you remove the entire control panel from the ceiling. Then you have very easy access to the back of the bulbs and they just twist right out.

I just put 5K VLEDs in my '21 4Runner. Your instructions are spot on. FYI, the same LED is used for the map lights, vanity lights, and door lights. Another LED is used for the dome light and the rear hatch lights. I had a hard time getting the dome light to seat properly and accidently separated the dome light receptacle from the grey frame. Finally got it working but I'm still wish the led module fit more secure in the holes.

Just got my 2024 TRD PRO ICE CAP 4RUNNER and going to the garage now to change out my LED BULBS!! Awesome video!!! Thank you

GREAT video. You helped me knock this out in 35 minutes from start to finish! THANK YOU

Thanks for the tape tip! I used packing tape and it worked great! I had seen others use painters tape or needle nose but neither of those were working for me.

Great video.....my install went exactly as the information shared. Thanks!

I cheaped out before seeing this video. Installed all the lights, we'll see how long they last.

This video was a blessing for me! I would like to one point. When prying on the covers for the door lights look for the arrow on the cover. The arrow points to the clip.

Just got a 4th Gen. Thanks for the vids! oops meant to say 5th Gen.

Great video ❤

Excellent video. Thanks!

Really helpful video - thanks!

Great video! Pro tip, on the door light lens, there's a small arrow on one side, that's the side with the clip. It makes it very easy to pop the assembly out. Keep up the great videos!

Great video, appreciate it.... I was looking for a dyi to change out the interior lights on my 2017 4runner.

Thank you thank you thank you!!

Just installed this kit today. Seem to be really good quality leds. One snag I had was one of the metal clips on the hatch lights popped off and fell inside. Had to pull the whole cover loose to retrieve it.

Warm lights interior, bright lights exterior

thank you!!!

Thank you for the best videos to upgrade 4Runner. Do you mind making a video for replacement of glovebox lightbulb.

Thanks, this is the best tutorial I found on how to change the original bulbs to LED. The tips on how to disassemble the door lights was great, I couldn’t figure it out on my own and didn’t want to break them. Question though, how snuggly were your bulbs fitting, especially the map lights? Mine worked, but were kinda loose. I couldn’t get them to push in and get that snug tight fit.

Nice

Great video, everything went smooth except the driver side map light. I got the halogen bulb out, but when trying to plug in the LED, the socket (aka female end) retreated into the panel! It is now loose and jiggling around up there. Are there any videos on how to remove that whole panel? Thanks!

Wonder is you could put some foil on the inside of the door ones to reflect the light from the leds that are hidden to get a little more light out of it?

Any advice on color choice?

Thanks for the great video just finished this upgrade, and ur video helped

@T4R Garage ... Another great video, thanks for sharing the knowledge. How well do the liftgate lights illuminate into the cargo area with these VLEDS? I can never seem to get enough light in there (after 3 different brand of LED upgrades) when the liftgate is open. Still searching for some very strong LED's to install.

what light is brighter natural or pure white?

can't purchase without buy the whole set

Great guide. I bought the bulbs in your link - but the map lights buzz every time they turn off in my 23 limited. Annoying af - maybe the bulbs aren’t good quality?

Hi great video.We would like to send a sample (Total new tesla style head unit) for 4runner for your review, but don't know how to contact you.

How have these held up??

What about the puddle lights?

$120.....Holy $hit!

The map light procedure in incorrect. The whole housing is designed to be pulled down, and the bulbs removed and installed from the top, with the fingers. Very easy.