The cheapest/simple DIY Analog USB Handbrake for SIM Racing 

I think you you could simplify things for your viewers by adding a dry list of components in the description, i've watched your vid for a second time just to do it. Add the amount of screws nuts etc. if necessary cause i don't want to watch it third time just to do it :D. Here's the list: components he used in the video: Galvanized flat connector 200x90 2 pieces M6x20mm screws nuts and connector nuts Joist Hanger type A 40x100 M4x10 screws nuts and washers 25mm chrome pipe and bike handle screw with retaining ring m6x60 m6x30 screw and nut compression spring 16x100 m6x50 screw nut, connector nut, washer and L shape bracket m6x50 screw, nut, connector nut, washer and 20mm rubber gasket 10k slide potentionometer 45mm arduino pro micro straight joining mending plate 50mm m4x60 screw, nuts and washer m6x30mm screws and nuts some packaging foam Thanks for the video, very useful for sim drifters or rally enjoyers :D

Don't worry about your drifting skills, you are pretty good to be learning. I am in the same point bro. Keep drifting.

2 years old thread, but worked out perfect for Me ! Up and running. Many thanks for the Ideas !

For the fact that you’re new to drifting you are crazy good 😮 and thanks for the tutorial btw😊

As a new drifter you are drifting very good

This is genius, minimal effort maximum performance. ✌🏻

0:00 - 0:16 - Intro 0:16 - 4:56 - Assembly 4:46 - 5:00 - Wiring diagram 5:00 - 9:15 - Finishing the assembly 9:15 - 11:23 - Installing and calibrating 11:23 - 13:42 Testing in Assetto Corsa

thank you so much for the tutorial also no need to worry about being new

I think I will build this, but without the connector nuts. They are really expensive nowadays.

Thank you a bunch for the video made the steps a hell of a lot easier, I just made my handbrake out a E46 handbrake and it’s rad cheers @Dano PT

this is sick! gonna try making something similar

Excellent home made brake. Well done 👍

Man, oh man... I want to build 4 of these because they could be used as normal pedals. The components are hard to source in my country and they are a bit expensive, especially the side plates (the ones in the video are too expensive and when you need 8 the cost ads up) and electronics (good luck finding the potentiometers). It took a while but I managed to reduce the price from around $100 to around $70 in total, cheaper than secondhand Thrustmaster t3pa pedals. For anyone in Romania, reply and I'll send you a constantly updated list of the parts you need.

Frumos lucrat si bine realizat. 🤝🍻

Hi friend, I really enjoy your projects. Have you ever thought about making sequence shifter?

Super tutorialul!! Am facut si eu una am gasit toate materialele in dedeman si leroy, in afara de switchuri (am folosit un controller de tastatura. Mi ar placea un tutorial pentru schimbator de viteze daca ai in plan ;) succes si la cati mai multi abonati

Nice Kit-bashing !

Nice job 👍

Ordered Pro Micro. Burned bootloader with Uno. Spent a day wondering why my pc doesn't see it. Broke micro usb socket. Next time i'm just going "mad max" with a real car.

Came here becuz I see ur post on Reddit ✌️

thnx nice video

great tutorial , im working on it rn and i have a question , wich cable to you think is better to use?

This is so helpful!

I have one question, is b10k with all lenght 45mm, and 30mm slide. Is that will work?

does this work for every game? it looks amazing by the way!

I'm considering building my own based on this design. What are your thoughts on the spring you chose? Ideally I'd want it to be a pretty heavy spring, how would you rate the one you chose here?

Is analog handbrake really useful? Any advantages over simple on-off button?

I'm stuck on the handle part, with the corks in place my ring that goes in the handle is super loose bangs around in the slit... hmm maybe duct tape the ring so its wider and muffles the metalic tapping?

Igot same stuff I bought everything at ace hardware

Omg u got the og shifter!

Awesome Video, I have a UNO R2 board, Im trying to run the software but it errors out, seeing it is not compatible with board, can this work with the R3 Uno board?

Could I use an Arduino nano that I have laying around for this? Or does it have to be a pro micro?

Ficou top vou tentar fazer um igual

Can i do that with 300x100x2,0 by cutting bad sides?

Nice job 💪 , ține-o tot așa 🥰.

Can you make a list like quantity of each screws, nut etc. Thank you.

hey i want to ask about arduino in tools only port i can use is COM1 and it doesnt work how can i fix this?

Hello, can I use some other chip to transmit signal via USB to the PC?

superb bro! imi fac si eu :D

what if i want to use a button instead of analog

The only joist hanger I'm able to get is 51x100. Do you think it will do the job ?

im about to attempt to make one but do you think instead of a sliding potentiometer that a rotating one will work?

Would this work on a ps4?

is that a progressive handbrake just because u are using that Arduino thing??? please tell me that im right!!!??? =)

do you get monetized for this vid bro? nice build

I got the arduino and everything to receive the code, however whenever I try to calibrate the slider the numbers are all over the place and won’t allow me to actually calibrate it. any ideas?

was there a list of the quantity of each posted anywhere?

do i need to start this software every time i want to play with it?

Very brilliant, can't find the flat connector in my contry, can supply a link?

It doesnt make sence .... you use 45mm potentiometer and 50mm plates .. but i dont think it is rally 45mm potentiometer .. because i do all same and potentiometer go only 20% no more ... i stuck here because i think you have less mm

Hey had a doubt can I connect my h shifter with the Arduino too?

keep getting this error: expected unqualified-id before '.' token its in the last sentence of the code any ideas?

Did you drill any extra holes in the Galvanized flat connector?

Hey, Does it only work on pc? Can I use this on xbox?

mate, i don have weld. i juz tie the hole & stick it on. Right now i am stuck in last part , when test the throttle botton, is out of control but still can push that button! have any idea can repair?

Hey, I am in America. Idk if you are, but how much did it cost you to make the whole build?

hi bro what arduino u use?

Can i Connect this handbreak to Xbox series?

Not pressure sensitive right ? All time 100% ?

is it recommended to use 22 AWG?

Bro switch name tell me bro

simply difficult

"cheapest"