No video :(

The Easiest way To Make Shaker Cabinet Doors DIY

Подписаться 5 тыс.

Просмотров 125 тыс.

50% 1

I am not kidding when I say this is the most simplest and easiest way to make your own shaker style cabinet doors. Follow me on this easy DIY step by step video tutorial making doors to suit your cabinet using basic tools and equipment. Also the method I will show you can be used to upgrade any plain boring flat door, turn it into a shaker style/panel looking door and add that lift to your joinery.
Affiliate Links:
Round Over Edging Router Bit Set:
amzn.to/3FmWf2f
Flush Trim Router Bit Set:
amzn.to/3mDtoAE
V-Groove Router Cutter Set:
amzn.to/420y560
Microjig Matchfit Clamp Set:
amzn.to/3jySpLD
Makita 18V Trimmer (I am NOT Sponsored by Makita):
amzn.to/3KXImuZ
Recording Equipment (Please note I am NOT Sponsored by these brands in any way):
Rode Wireless Go II:
amzn.to/3IYGKOK
Rode Lavalier Go Professional Mic:
amzn.to/3J2ITcq
Sony ZV-E10 Digital Camera & Vlogger Kit:
amzn.to/3AEGsJm

Опубликовано:

27 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 57

@rosetealatte9282 11 месяцев назад

Just bought an older house with outdated cupboards. We are on a budget, and this fits the bill. Thank you so much for sharing.

@geoffsjoinery4990 11 месяцев назад

Good on you, great to hear 👍

@megadeclutter 6 месяцев назад

I love how you showed the inexpensive option, especially with the weights. I do not have clamps and have been putting off buying them, but I see I can easily use what I have around like weights or maybe clean bricks, books etc. Thank you!

@geoffsjoinery4990 6 месяцев назад

Yes if you don’t have weights you can use things like bricks, buckets even filled with water or sand…good luck with your project 👍

@aidsh6648 Год назад

A1 video. Please don't stop making these

@PapaJoeWalsh 11 месяцев назад

Great video! Thanks for sharing. Perfect timing for making my first cupboard doors!

@emotionalmodels8463 21 день назад

You just made my profit increase big time!!! 🎉🎉🎉🎉

@whomadethatsaltysoup 9 месяцев назад

Thank you so much for sharing! Defo', the easiest way to make fake Shaker doors. Your point about the pin gun is a good one. I have an 18 and 16g second fix pin gun, but both are far too fat and long to be useful in this scenario. However, recently, I remembered the old analogue days, aka, thumping them in with a hammer, and bought some veneer pins that are only 1mm by 10 to 30mm. Perfect for the task. They won't poke through the door, or leave an excessively large pinhole to fill. The 23g pin guns, the corded and cordless ones, that is, are just far too expensive!

@geoffsjoinery4990 9 месяцев назад

Thanks for your feedback, be sure to watch my 2nd video on making shaker doors with a slight design difference you might like...👍

@msBridgetB 10 месяцев назад

Thank you so much for this video, you made it so easy for me a beginner diyer.

@geoffsjoinery4990 10 месяцев назад

Great to hear good on you 👍

@chubbieminami3274 10 месяцев назад

Thank you so much. I was wondering how to make cabinet doors. I think I will use your method. I have a boring flat door. I might do the same on the door too.

@geoffsjoinery4990 10 месяцев назад

Good on you, have a go! Thanks for watching and your nice comment 👍

@antoinettefarrugia6513 Год назад

Great video as always thanks

@geoffsjoinery4990 Год назад

Thanks so much for your support 😁

@inkironmojo775 11 месяцев назад

Love it … simple, effective and looks perfecto

@kathyr.6825 9 месяцев назад

Do I need a table saw? I have just about everything but that..!! 😮 thank you 🙏 like the music as well!!

@tracihaynie4818 3 месяца назад

This video is a lifesaver! accidentally used my ½" birch as the base instead of my ¼" (I typically do ¼" as the base and ½" as my trim) so this video helped remind me I can switch it up for these cabinets. One question: What type of router bit did you use?

@geoffsjoinery4990 2 месяца назад

For the edges just the smallest round over bit - 1.5 (1/32” or 1/16”)

@markbentley6255 8 месяцев назад

put the stiles on first and then squeeze the rails in... easier for adjustment if needed

@canadianbacon79 10 месяцев назад

Definitely something I need to update my kitchen on a budget. Would you recommend edge banding, or wood filler and sand before painting?

@geoffsjoinery4990 10 месяцев назад

If you plan on painting your doors then wood filler and sand should be fine. You will need a couple of coats of undercoat especially when using raw MDF. I have made many of these doors for my clients and get them sprayed in polyurethane and they come up a treat! Good luck with your project and thanks for watching 👍

@tonystrumberger5857 7 месяцев назад

I've made doors that exact way the only problem Is the doors tend to bow due to the wayoff gluing stills to door. Next time i will put dots of glue to see if its any better . Cause for bow is to much glue

@aleksandarbasaric1533 5 месяцев назад

Never understood why it doesn’t always get done this way if it’s just MDF that’s getting painted anyway so easily just a bit of putty on that joint. Do you know any reasons why everyone tends to do it the hard way? Thanks mate 👍

@geoffsjoinery4990 5 месяцев назад

Exactly right and it’s fairly cheap too 👍

@Tackleberry_G1094 7 месяцев назад

For the styles and rails you use 5 mm mdf. Would hard board be the same (the material used for cabinet drawer bottoms) If so can you sand it?

@geoffsjoinery4990 7 месяцев назад

Yes no problem especially if you are going to paint the doors you won't notice any difference in the materials used. Sand smooth, fill in any nail holes, undercoat well then cover with at least 2 x coats of your colour. Good luck and thanks for watching👍

@mikefitz445 2 месяца назад

Since you'll be painting this style door, is using glue and a few brad nails in edition to clamps a reasonable option?

@andrewforest8935 9 месяцев назад

Great video, what thickness material is on the inside of the door? It looks like the front panel is between 2 rails/styles. Is it all 1/4 MDF?

@geoffsjoinery4990 9 месяцев назад

You can use 1/4" if you like, I used 1/2"

@bababooey1266 8 месяцев назад

Good video. Good thing it wasn’t a windy day in your garage, your hat would’ve blown right off your head

@jeevespreston 6 месяцев назад

Nice technique, I’m curious as to the longevity of MDF as cabinet doors in the kitchen…

@geoffsjoinery4990 5 месяцев назад

If I use these in a kitchen, they are totally sealed then finished in 2 pak polyurethane and there’s no problem even using on a vanity. Providing of course you don’t go bashing or scratching deep into the surface exposing the raw MDF were you will allow moisture to enter! 👍

@jimgeelan5949 10 месяцев назад

If your starting to do joinery ( gluing two bits of mdf together is not joinery) you best get a pin gun because your production rate is not going to make you a living working like that

@eliasantonioruizgonzalez1836 11 месяцев назад

Pienso utilizar mdf 5/8" (9/16") y mdf 1/4" (3/16") de esta manera quedaria la puerta exactamente 3/4" de espesor....estaria bien hacerlo asi? Que me recomiendas?.... gracias de antemano por tu ayuda...saludos desde san luis rio col. Sonora, Mex.

@geoffsjoinery4990 11 месяцев назад

Yes that would be perfect and exactly what I have done. 👍👌

@darrenlesueur4785 8 месяцев назад

I've made 1000 of door with 3/8 back panel and 3 inch wide 3/8 molding I always oversize the doors 1 /16 all the way around to trim all the way around . I always use 23 gauge pin nails and spring clamps . when you spray the first coat you can putty the nail holes then .

@geoffsjoinery4990 8 месяцев назад

Mate your a legend 👍

@darrenlesueur4785 8 месяцев назад

@geoffsjoinery4990 it wasn't worth the hassle though .I thought I had to make all my doors for my buisness when I first started 10 years ago . now I just ordered all my doors from a company that just builds doors, and they come sanded and ready to be painted . it eliminates all of the hassle . the place that this type of method is great for is making paneling for the sides and backs of islands

@unfocusedjoker4374 10 месяцев назад

Would this work with 12mm mdf with 6mm straps?

@geoffsjoinery4990 9 месяцев назад

Yes 100%

@callyscraftycorner2463 11 месяцев назад

Nice, do you recommend using plywood and if so, how would I hide the edge of the plywood?

@geoffsjoinery4990 11 месяцев назад

You could use plywood if you like the only thing is the raw layers on the ends. You could use a thin 0.5mm veneer iron edge when your finished then trim flush and that would look great. see my video on applying edge banding by hand, I have done a demonstration using 0.5mm PVC but the principle is the same. Good luck with your project 👍

@callyscraftycorner2463 11 месяцев назад

Thank you!

@reedyrod Год назад

If you only have 16mm you wont get a kitchen type hinge in them they need to be thicker at least 20mm.

@geoffsjoinery4990 Год назад

That’s not entirely true my friend, most concealed hinges including the BLUMOTION 110deg (71B3550) I use require a min depth cup hole of 13mm. Trust me I have been doing this for years there is no problem hinging a 16mm door. Thanks for Watching 👍

@janvandervaart979 5 месяцев назад

deurtjes zullen kromtrekken door het even aantal lagen

@sajidrafique375 7 месяцев назад

Will Screws hold good on MDF ? I doubt it

@coggsy3036 10 месяцев назад

Who did you borrow the weights off🤔

@geoffsjoinery4990 10 месяцев назад

Haha I’ve had them for over 25yrs now my boys use them 🤣

@user-oj7yd8iw3q 11 месяцев назад

good

@agagagoghi 11 месяцев назад

Sorry but You often trim in wrong direction.

@leanchasersx 10 месяцев назад

Thanks for the comment. It made me look up what the correct way to route is. It explains why it kept jumping when I was redoing my vanity top with laminate.