This is How To adjust limits on Overhead Door Legacy 696CD-B garage chain drive opener - DIY 

Glad you enjoyed it!

You're welcome! Thank you for watching 🙌

Glad I could help. Thank you for watching 🙌🙏

Thank you for the reply. I appreciate it and it makes me happy to hear you were able to get your motor repaired while saving you tons of $$$$$. Feel free to reach out if you have any future issues with the motor. Thank you 🙏

Your welcome 🤗 Glad I could help and hope it’s back running good as new. 🙌🌟

Absolutely and I appreciate the feedback and kind words. Glad it helped and thank you for watching 🙏🧸

Excellent! Glad to hear it’s back working 🤗🧸

You're welcome! Glad it helped and thank you for the comment :)

You’re welcome. Yes they are as long as it has the same limit set up on the back of it then it should work similarly.

Glad it helped. I appreciate you sharing your feedback and thank you for watching 🙏😎

You're welcome! Thank you for the feedback

Nice work! Glad it helped and thank you for watching.

You're welcome! I appreciate the feedback thank you 🙏

Any time! Glad it was helpful and thank you for watching and commenting 🙏🙌

You bet!🙌

You're welcome! Glad it help and thank you for watching

If its reversing while you attempt to set the limits then that means it could be one of the following : * the springs on the door are too strong causing the motor to struggle to close it… a way to check if this is the problem is to release the door from the trolley ( pull the emergency cord) and try closing the door manually. If it closes fine without resistance then that’s not the problem. If you trouble pulling the door down bc it’s trying to go back open, then the springs are in fact too strong and this will cause it to reverse. If not this then , * Check the “close force” setting on the back of the motor near the limit button. Turn the force setting clockwise to ensure it’s turned all the way up ⬆️ if it’s already turned up then that’s not the problem. * You may have a bad rpm sensor. Those are easy fixes with the swap of a part but could also be a faulty logic board or known as mother board. Both of these parts are plug n play. * Next check your sensors and ensure both are lit up and properly aligned facing each other. Make sure nothing is blocking them. When a sensor gets obstructed or off alignment, the door will reverse as a safety feature. This happens so it doesn’t crush a car, child, pet , item , etc. * Lastly you may have a bad gear ⚙️. Not all models have this function but press the motor button one time and when it reverses or fails, you should see a light on the back of the motor where the limits are…. The light should flash a number of times. Count it and depending on how many times it flashes , it’s a error code. Google to model and error code flashes. It will tell you what component has failed and that should lead you to one of the areas I listed. Hope that helps and I really appreciate you reaching out. Thank you for watching and give me a status update if you find out. Thanks 🙏

Follow the steps in the video to close it. Once you do , you can adjust the settings on the back of the unit to program the close limit as I show in the video. Hope you can get it fixed.

I’m confused. Do you see two set screws in the circle at all? If you see two then we can adjust it from there….

Send me your contact info please to Garagemanteddy@gmail.com and I’ll see if I can assist you from there

I don’t have one on this model , but the force settings are on the back of the motor next to the limit button I was pressing. It should say open force and close force on the them. Just turn them clock wise to increase pressure or opposite to decrease.

Awesome. Thank you very much. @@GARAGEMANTEDDY

Hi Dinot71, If it has the same set up then yes. Let me know if it doesn’t and I can help.

Thank you for the information. I responded to your email. Keep me posted.

Let me know if that helps. Thank you for watching 🙏