This Jeep Is An Absolute DISASTER… Can We Fix It?! 

You're getting the video balance of comedy, explanation, and fabrication pretty dialed, Y'all. Meanwhile my little baby TJ is outside just jealous as all Hell.

8 and 2 ticks over the big one in the middle 🤦🏻‍♂️

You leave Jake out of the mess you`re makin`... I really enjoy your content! Your videos are addictive!

Wow your guys channel is dialed in. Awsome content with the lol moments plus the killer editing wish i found it sooner.

Awesome way to start my Sunday morning by getting to watch YOUR channel before everyone else's! 👊

Love your videos FYI you may want to look at the Smart tool angel finder. I used it to set up my rear end in a drag truck.

Man you guys got a wining lotto ticket being able to do fun stuff and get $ outta it with your brothers is unreal.

Caleb reads a tape measure like I do 😂

It's a really cool channel~ And great friends~!! I will always support you!!👍👍👍

Hi , the crossmember definitely , looks manufactured , good job .

Cross member is beginner fab shop. You welded it. Grinded it. Textured it. Next step would have been fish plating the seams you welded/grinded. . Great job.🤘🏼

Love you guys! Thanks for posting.

Always so much fun watching you guys fabricate 👍🏻👍🏻👍🏻

When ever you all are working on anything , For some reason it always looks like One of you is about to get hurt pretty bad, Love you're content and editing skills, leaving in the parts where things get ScReWy , great family, showing that you all are just at like most of us !!!! "LUVINIOLDTRX"

looks great brother,better then what id lay down

Thanks for the new episode. Love the content and the builds.

You all are awesome 👌

That crossmember is pure backyard fab shop. A fab shop would have a bender to make that.

Love your channel. Keep’em coming!

What if rather than cut the seats out 😂 you made a reinforced 3 piece crossmember comes out. I mean even the factory one comes out for service

I saw that crossmember interference long before you did. You must not have heard me tell you that while you were building it. I tried. I yelled at the video. Nobody listens. :)

Best Jeep content on the Tube!

I laugh way to much at these! Man it reminds me so much of working with my boys!

Monkeys and a football comes to mind watching the vice action 😂

Is good that you guys have eachother to work with the jeeps and come up with the best ideas posible for killer jeep mods 😅🤣🤣🤣

Looks like Peck Brothers Fabrication

Why scrap the ORI’s?

What Bumpers are you using?

Yall crack me up, love the videos! Hope to wheel with y’all someday 🤘🏻

Holy Crossmember Dude! Please tell me you guys don't always cut parts and fabricate on a aluminum bench? Not staged for content RIGHT? Lol Hopefully a Welding table makes it into the new shop!! Love you guys though!

Why not scalp the top of that rear crossmember and cap weld a new top that’s shorter and not need to cut the tub?

What is the wheel base?

what about the previous manual trans was causing you to break parts?

Keep em' coming!

Y’all should bring these bad ass rigs down south would love to watch them work in a different environment then y’all are used to but these rigs would perform really well. Love the channel and the rigs

You guys are a hoot! Love the clean fun and fairly good fab work lol!! Let's wheel!

Remake it in dom 120 wall tube it will take some of the space out that you need, or make a bolt in middle ans keep it striaght across allowing the drop out service

He expects to work on it as much as Caleb works on his Jeep

Do trailer park residents have back yards? Nice to see you guys working on the rigs.

Fabrication shop

Just Dean It!

There’s a handful of brands that make crossmembers exactly like that. Could have bought one of theirs or at least taken measurements off them. RPM steering and Hepta MFG to name 2.

Not pure backyard but nowhere near fabrication shop lol

I am sure this has been asked and explained. Is there an actual Dean and is he perfect?

That crossmember looks like my blind grandmother who also has Alzheimer’s welded it up. 😂 totally kidding

Cross-member looks like it was fabricated in a totally backyard fab shop!!😂😂

America 🇺🇸 💪🏼🤙🏼

You need plywood or sheet metal on your concrete or the sparks will screw the finish up

Someone enlighten me. What is a: Dean; Dien, ding? Just curious never heard anyone say that.

Looks Farm Fresh 😂😂😂

That's a lot of bends for a crossmember. I'd take that off and sell it to McDonalds