TOPDON Battery Tester BT200 | Mechanic Mindset

Подписаться 53 тыс.

Просмотров 53 тыс.

50% 1

Quick look at the TOPDON BT200 battery tester. We perform test on a good and bad car battery, using the battery test, cranking test and charging test functions. Using a battery tester to check battery condition is a much more accurate method than using a volt meter, we look at why.
www.mechanicmindset.com/
USA Product Links:
TOPDON BT200 Battery Tester: amzn.to/3ueMIlc
UK Product Links:
TOPDON BT200 Battery Tester: amzn.to/3wqgS6L
20% off code: S2IHEFWO
THANKS for using our product links; we get a small commission from ANYTHING you buy at no extra cost to you!! We invest that money back in to the channel to increase your viewing pleasure!
Link to PicoScope Waveforms: www.mechanicmindset.com/share/76
My PicoScope Set Up: kit.co/mechanicmindset
Follow us on Facebook: / mechanicmindset
Video Links:
Best & Cheapest Automotive Scope - • CHEAP AUTOMOTIVE OSCIL...
Pico 2204A HACKED - • Video
4 CAN Bus Faults Diagnosed - • HOW TO DIAGNOSE CAN BU...
CAN Bus Multimeter Test - • How To Test CAN BUS Wi...
5 Easy Oscilloscope Tips - • BASIC AUTOMOTIVE OSCIL...
Quick Misfire Check - • FIND MISFIRES FAST! [H...
PicoScope Compression Test - • GOOD vs BAD RELATIVE C...
Hantek CC-650 Amp Clamp - • HANTEK CC-650 AUTOMOTI...
The Mechanic Mindset channel is here to help you improve your automotive diagnostic skills. We upload regular, easy to understand, automotive training and tutorial videos covering topics such as; oscilloscope diagnostics, PicoScope, CAN bus, waveform analysis and much more! Subscribe to stay up to date!

Авто/Мото

Опубликовано:

22 май 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 89

@PJANGELES30 2 месяца назад

First class presentation. not one wasted word. Comprehensive also.

@MechanicMindset 2 месяца назад

Thanks! So good to hear your appreciation 😁

@NortonUnofficial Год назад

Really clear explanation. Just what I was looking for. Thank you.

@pmtips4482 3 года назад

I like these testers. The battery health report works real good. My 08 Civic had a 7 year old battery in it and it showed a 70 percent health rating at 75 degrees ambient temperature. Car was starting, running, and charging just fine but it was in the summertime. That fall as soon as we had a below freezing night of probably 27°, the old Civic just grunted, turned over about 2 or 3 times real slow and that was it. A new battery took care of it so the report was spot on in my case. The tester was a Foxwell BT705.

@MechanicMindset 3 года назад

Awesome, batteries are really sensitive to temperature! The second battery I tested, didn’t think it was going to last the winter. But me being a typical mechanic, leave it till it fails. It still starts the engine 😂

@PDR-wb9dq 3 года назад

I have the TOPDON BT100 very similar all the same functions only slightly smaller and no colour display, I have been very happy with mine and its half the price too...

@ivandunne6493 3 месяца назад

Many thanks, so much better than the manual which I can barely see!

@fuseone 3 года назад

Just was looking at one for home use, definitely will pick one up now.

@MechanicMindset 3 года назад

Cool, the voltmeter is an ok method but you will know for sure with one of these! 👍

@arthurfricchione8119 3 года назад

Darren thanks for sharing. Looks like a decent tool. Will check it out. Stay safe and well Artie 😊

@MechanicMindset 3 года назад

Cheers Artie!

@TheDutyPaid Год назад

Nice clear short video, I'm going to order one just based on this.

@MechanicMindset Год назад

It’s a great little unit 👍

@alrifainidal 3 года назад

nice to see you again mate

@MechanicMindset 3 года назад

Hey Nidal, it’s been a busy winter with terrible weather 👍

@livefromplanetearth Год назад

thanks for teaching

@htownblue11 3 года назад

Great review, and educational for those who haven’t used a true tester. Like you clearly showed, voltage can be a liar with respect to battery health which has to include amperage delivery into a proper health assessment. The TopDon would be my next purchase for a tester if mine ever goes out. Yet another good video.

@MechanicMindset 3 года назад

It's sometimes misunderstood, the voltage gives us State of Charge, but not the internal resistance. We can do a crank test but it's still not totally accurate. Hope you enjoy the purchase, they make some nice equipment! Cheers

@paulwharton1850 2 года назад

Excellent video - Ordered one.

@MechanicMindset 2 года назад

It’s a cool little tool 👍

@stephanevaucelles6378 3 года назад

Hello thank you for the presentation of this tools

@MechanicMindset 3 года назад

Hi Stephan, thanks for watching 👍

@stephanevaucelles6378 3 года назад

@@MechanicMindset at work we use my midtronic precaunized by Renault truck

@surendersingal2192 Год назад

Thank you sir.

@jeffreyherbert91 3 года назад

I have this model and really like it....though i dont use the charging test as it does not work well for smart charging and found the instructions unclear as test says loaded and unloaded which to me means you need to turn some consumers on....but it goes straight into both loaded and unloaded testing without giving you a chance to switch on consumers. You are correct with your point about connecting direct to the battery even testing a small distance from the terminals alters results..i did some googling for advice re health percentages and it appears 65% health is the point at which to consider replacing the battery

@MechanicMindset 3 года назад

Ah good to know, batteries are really difficult to diagnose sometimes. I had this one car where start/stop wouldn’t work. The battery SoC was fine, no issues starting the battery, put a new one on and it was all good. Yes, it only asked for rpm increase and not electrical load... I don’t think this will test a smart charge system, probably best with an scope and amp clamp 👍

@BabyGangsterIsMe Год назад

why u dont understand load and unload battery testing ? loaded mean your car has the battery already installed .. unloaded means the battery itself ..so easy to understand without the booklet

@slucas8258 11 месяцев назад

@@BabyGangsterIsMe Wrong

@patelvivek4888 3 года назад

Nice video 👍

@MechanicMindset 3 года назад

Cheers!

@ctuagent31 3 месяца назад

Just tested my tractor battery that had been sitting disconnected all winter. Initial reading was replace battery. After I jumped it with my Autowit and ran for a while I tested again. It said healthy battery but the display said “check tester “? Any ideas. It doesn’t say anything about that in the manual.

@tonyisme4934 11 месяцев назад

Ok my Topdon BT100 on the charging test shows NO-OUTPUT and about 9.4V with a brand new charged 12V battery. Battery test passes at 700 CCA. Any ideas? The booklet does not show this reading NO-OUTPUT

@bleebleblahble8833 3 года назад

Buy this BT200 one over the BT Mobile Version. I am continuing to work with them to get them to fix the software on the bluetooth version. They had the loaded and unloaded voltage results flipped and the alogrithm for a pass/fail on the charging test was wrong. Should be fixed now but i still have my hesitancy and trusting this versus something like a Midtronics which is the gold standard. Or even better a scope with an amp clamp.

@MechanicMindset 3 года назад

I need to do some battery diag with the scope 👌 cheers

@bleebleblahble8833 3 года назад

Justin Miller has a great video on it if you need ideas

@404notfound..... 2 года назад

Excellent video, but overall I'm gonna stay with the industry standard which is Midtronic's. One thing I would like to see, test the Top Don with a Volt meter and see if the numbers are the same, typically with overseas testers the algorithms are not correct, the numbers are there, but they are not correct.

@MechanicMindset 2 года назад

I would take this test by my meters haven’t been calibrated for 10 years 😂 (I’m not on the shop floor by the way)

@ADDAUTOMOBILESERVICES 3 года назад

👍

@cesargalvan3750 3 года назад

Good video, one question: I have a winch installed in my truck( with no isolator), should this affects the measurement for crank test, as well charging test? ( for sure not turn on the winch), Regards

@MechanicMindset 3 года назад

Hi, if the winch is turned off then no, it won’t affect the cranking or charging test. Cheers!

@____HEISENBERG____ 4 месяца назад

What is the M button used for?

@jamesj9325 8 месяцев назад

Darren, yes this TopDon works well for ICE and un connected batteries. Why does its B test state VOLTAGE TOO HIGH, REMOVE SURFACE CHARGE ie. TURN ON HEADLIGHTS when testing small 12 volt battery connected in Tesla MY? Perhaps it was being charged from big battery and or voltage was found about 13 volts? Curious the similar Tesla Hankook un connected battery tested 100% health and 100% charge at 12.63 volts. James

@MechanicMindset 8 месяцев назад

Yes possibly. EVs have an inverter for the 12v system as they have no alternator (ie 400v > 14.5v). This can be active with the ignition on, but also after switching off. There’s also possibility of a slight discharge from capacitors bringing the voltage up a bit.

@pmtips4482 3 года назад

The 55 % health on your good battery is low. That battery will not be a good battery when temps go below freezing. That's my experience anyway. These testers are only as good as the data entered, sometimes it's hard to get the CCA of the battery. Great video and thanks!

@MechanicMindset 3 года назад

I did wonder about that rating; good SoC, low internal resistance. Seemed like a newish battery too. I got the CCA of this one ok, it was the type I struggled to confirm. But that would make sense if all the other readings were ok. Cheers 👍

@MechanicMindset 3 года назад

.....a test directly on the battery poles may bring the health reading up 🤔

@Okie-Tom 6 месяцев назад

I also thought the state of health was low at 55%. Most everyone will replace a battery before then. My local mechanic says he prefers to replace a battery below 75% health! I just had my car show a warning on the dash and my battery health says 57%!

@norbertrivera 2 года назад

Any comment about using those devices, battery load testers, with solar deep cycle batteries?

@MechanicMindset 2 года назад

Sorry not sure, might be best to contact TopDon directly 👍

@mrmorganmusic Месяц назад

I just bought one of these testers for my deep cycle RV 12Vv batteries. I don’t know much about how these work, and want to learn more. Does this run a load test?

@MechanicMindset Месяц назад

Great. It’s not a fully ‘loaded’ test, but it does work out internal resistance. From memory, it checks battery voltage during cranking too (which is a load test of sorts)

@DJ-tn7vj 3 года назад

Hi D. What's up? Is there any tester that can display the details without looking it up. I saw autel came out with some and there is the high end one that diagnose Dan uses. Is it Bluetooth?

@MechanicMindset 3 года назад

Hey, ah ok not sure, will look in to it 👍 this isn’t Bluetooth

@bleebleblahble8833 3 года назад

@@MechanicMindset the BT Mobile version does this via the app but the charging test is not the most accurate other than that great tool that also shows internal resistance, ripple, etc.

@MechanicMindset 3 года назад

@@bleebleblahble8833 Got you, I did just see it. Interesting the way tech is going. It won’t be long before we just connect the phone to the car with no VCI, via the telematics !

@50450720 Год назад

I'd be interested to see the poor battery put through a reconditioning cycle that some of the better battery chargers offer, and then see it retested to see what difference it made.

@nenadkrneta1551 4 месяца назад

I tried it. It almost did nothing from 60 to 65%. Battery tester was still blinking replace battery. I think that the best thing is to use recondition a couple times every year not when the battery is bad. When its bad it so late to do anything.

@GayorgVonTrapp Год назад

At 2:06 when you get to the 680 EN standard, I’m confused. I have a brand new 12v 100ah Gel leisure battery (from Photonic Universe) and nowhere on the battery or in the docs does it give any info of this nature, such that I can select the correct setting and value. I’ve googled it and can’t find this info. Any ideas?

@MechanicMindset Год назад

EN was the standard I chose to identify this battery. You should be able to select EN, SAE, CCA or Ah; they are all different spec ratings for batteries and usually the battery tester will give you the option to input the data you have

@GayorgVonTrapp Год назад

@@MechanicMindset Hi, and thanks. The only info I seem to have is that it is a 12v, 100aH, Gel battery. That’s it. I chose the GB setting (which stands for China?) and set it to 100 (as in aH), and got a battery health of 8% 👀. It says to replace the battery but that can’t be right.

@MechanicMindset Год назад

@@GayorgVonTrapp not sure I’m afraid, never really work with leisure batteries. The tester should cater for them though as it has Gel setting

@GayorgVonTrapp Год назад

@@MechanicMindset Yep it should. Thanks for your efforts. If I suss it out I’ll upload a video especially on this subject. Have a good Christmas.

@dopiaza2006 Год назад

A leisure battery will not have a CCA rating as it is not designed for very high current output condtions like engine starting. CCA means cold cranking amps - only really relevant for an automotive battery.

@johnholmes6811 11 месяцев назад

How would this work with a hybrid engine car?

@MechanicMindset 11 месяцев назад

If it has a conventional AGM battery, it’s ok. Charging test probably return a fail though

@u.e.u.e. Год назад

Hello, does the Topdon also have a German menu?

@MechanicMindset Год назад

Sorry, not sure. I don’t have it right now. Maybe it is explained in the website 👍

@Jax281 2 года назад

Will this work on a leisure battery

@MechanicMindset 2 года назад

I think so, they are usually gel batteries and I think it has the setting 👍

@MechanicMindset 2 года назад

This might help: ru-vid.comkdH4P7szDwo?feature=share

@TGam-wo2vd 3 года назад

First view, first comment. Good content man.

@MechanicMindset 3 года назад

I have this image of you sitting and waiting for me to upload, good work 😂. Cheers!

@waynebeck7801 Год назад

If you test the same battery more than once you will probably get different results each time.

@MechanicMindset Год назад

It was the same with the top end Midtronics battery tester we used to use in the dealer. I had a freind who worked a Varta; he didn’t rate any battery tester, but gives us a rough idea. It’s very sensitive electronics in not so perfect conditions I suppose

@dopiaza2006 Год назад

It didn't take 2.6 seconds to start the engine, would be surprised if it was more than 1 second.

@alexchong213 2 года назад

Sorry but I have one and while it does test ok, it's got basic spelling mistakes on the screen, product 4 of 5 stars

@MechanicMindset 2 года назад

Thanks for feedback!

@arnobruynen6073 2 года назад

This battery tester is just a clone of the Ancel BA101 which I've used for like 2 years now. My BA101 has the exact same spelling errors in the menu. And the Ancel is just a clone of another battery tester. Topdon is just another Chinese diagnostic tools manufacturer like there are so many already. They all just copy each others work, change the look and feel a bit and slap their own brand on it.

@littlereptilian7580 Год назад

@@arnobruynen6073 lol. Clone of a clone hahahah. Ahhh these Chinese....

@Merssall 11 месяцев назад

Engine must be on isnt it ??

@MechanicMindset 11 месяцев назад

Only for charging test. Follow the instructions on the tool 👍

@GripFreak Год назад

Perhaps batteries are not your area of expertise as you have stated numerous false statements. You're obviously trying to make money off the sells of this device. Knowing the different types of batteries are essential to accurate troubleshooting. Using a digital voltmeter with DC volts accuracy of at least 0.25% is an accurate method if one knows what they are doing. The BT 200 does not account for ambient temperature. This metric is up to the technician to ascertain. The BT 200 is a conductance type tester and does not accurately load test the battery. I have conducted hundreds of controlled battery tests (flooded LA, AGM and Gel) with various conductance type testers and have found that most are not reliable and much of their advertised information is simply false.

@dopiaza2006 Год назад

Gosh, what a guy you are!

@MAIEMI 10 месяцев назад

Behhh onestamente non mi sembra un prodotto affidabile, ho il BT200 di questo marchio, batteria tenuta bene e sempre ricaricata, ho una exide premium 64ah con 640 di spunto, dopo 5 anni di utilizzo la batteria ancora va bene, con questo dispositivo mi dice da cambiare perché sta al 66% di vita con 520 di spunto, oggi vado a ricontrollare e mi da gli stessi valori, solamente tensione a 12.49, mentre il primo test stava a 12.59, ma adesso mi da batteria buona, penso che se da , da sostituire, non può dopo dare un esito batteria buona, calcolando che l avevo ricaricata la volta scorsa, e con 12.8 di tensione mi dava ugualmente da sostituire, quindi il prodotto lo ritengo non affidabile

@Mickytdi 3 года назад

55% health isn’t really a “good battery”

@MechanicMindset 3 года назад

I suppose it depends on the scale that is programmed in the tester (i.e. the point it turns to bad). To be honest, I had no suspicion the battery would fail, it was a newish battery on a 2018 car, the static and crank voltage was ok with low internal resistance. Adds up to me, but I know what you mean; it sounds low

@Mickytdi 3 года назад

@@MechanicMindset i have a Varta AGM ( 680a) 4 years old and is reading anything between 45-55% ( depending on ambient temp) New batteries are reading 100% in comparison. My battery performs fine, you could leave lights on for ages and the car will still start, the start stop system works flawlessly. However if temps drop below 3 degrees centigrade it does begin to struggle. Also puts errors on the dash etc. If it’s cold out i often get the “ replace battery “ in the summer like now it reads “ good battery”.