Toyota Lexus CV Axle Fiasco

Подписаться 457 тыс.

Просмотров 86 тыс.

50% 1

Some Toyota and Lexus vehicles have a carrier bearing on the CV axle on the passenger side. These can rust up and on this 2008 Lexus ES350 when it wouldn't pound out, I had to cut it out to complete the job properly. Watch how we did it.
Products used & referred to in the video↓
Plasma Cutter → amzn.to/2FaHPSb
(also requires air compressor not included or shown)
Milwaukee Impact gun → amzn.to/2D2AinH
Facebook → briansmobile1
Instagram → briansmobile1
Twitter → briansmobile1
Pull-a-Part Challenge video 3 → • The Pull-A-Part Challe...
Disclaimer:
DO YOUR HOMEWORK before making a decision based on information you find on RU-vid, or anywhere else when it comes to your car, the environment, or your safety.
Due to factors beyond the control of briansmobile1, briansmobile1 assumes no liability for injury or property damage incurred as a result of the presentation of this information contained in this here video or any of the other briansmobile1 videos.
briansmobile1 recommends safe practices including the use of personal protective equipment such as eye protection, hearing protection, gloves, guards, shields, and respiratory protective devices when working on vehicles and or with tools seen or implied in this video.
I am an Amazon affiliate, Prime member, and general Amazon nut. I provide links to help you find the right stuff for the job quickly, confidently, and conveniently.
Thanks for watching my videos. I hope they've helped you tackle something you thought was a challenge and left you feeling empowered! And if nothing else, perhaps you had a laugh and were entertained!

Опубликовано:

1 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 255

@JodianGaming 5 месяцев назад

Replaced a lot of these working at Toyota and have never had to resort to cutting the shaft. There are a few different ways to get around the bracket dowels. Easiest way is to loosen the bolts on the housing so the housing moves slightly, as you only actually need about 1-degree of flex for it to get off the pins. Another way some guys do it is to run a thin saw blade up there to cut the the dowels. We always grind them off anyway before putting the bracket back. When installing the bearing bracket back on the new shaft, it works best to put a little lube on the inside of the hangar so the bearing slides in better. Also didn't see ya put the rubber-tipped bolt back in to hold the bearing. That's a needed part, keeps torque from spinning the bearing in the bracket.

@briang804 6 лет назад

I have been working on Toyota’s and Lexus ‘s for 15 years In cold weather climates with rust and have never had to do this. Just use an air hammer and a pry bar.

@briansmobile1 6 лет назад

Do you just hit the carrier?

@gordbaker896 6 лет назад

Good for you. after hours of labour, even getting a longer bolt and cracking the bearing cup in the carrrier it still would not move. Sawzall 10 minutes and Out. PIece could not be knocked out, I had to punch individual ball bearings out where the Circlip legs are untill it fell out, then punch out the remains of the cup. Unbelievable corrosion much like Mill Scale. Stupid setup.

@Nomoreendlesswars 5 лет назад

I have an engine pulled where I had to cut the axle shaft I still cannot get this bracket and bearing separated and there’s all the room in the world. Where do you take the air hammer too

@jayrenner7565 3 года назад

@@Nomoreendlesswars Right at the inner hub. Beat it to death with an air hammer/chisel.

@moosemobileautorepair 2 года назад

@@briansmobile1 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-99SpwwzgJik.htmlm27s

@rizwanahmed11 2 года назад

The best 70-100 dollar you can spend is to get a new bracket before this job, and Dremel cut the old bracket (make a cut to the width of the bracket where the bearing sit), literally 5 min and that bearing will be out. This is what I learned after spending 3 days hammering , using slide hammer, heat , air hammer, chisel, pry bar, and unable to cut the old cv using sawzall and diablo carbide blade, all of it) . Just go get a new bracket and cut old one off. You will spend same money on material, frustration and on time trying to get this out any other way. Dont cut the shaft (home DIY guys will not be able to cut the shaft any way especially on Avalon because there is no room) cut the bracket and it will be out. Part number is Dorman 926-193 is for Avalon 2008. You are welcome.

@davidhimmelsbach557 Год назад

Since Hamlet, this is the worst tragedy I've encountered. BTW, Diablo makes a TC sawzall blade that cuts these axles to pieces -- drastically faster. I'm glad I caught you just in time.

@JustLikeGreta 5 лет назад

Lots of comments here. I'll tell what works if the Toyota/Lexus has been driven in the cold climates with lots of salt. Don't waste your time and money with gimmicks. Cut the damn engine mount/carrier bearing with an angle grinder. Hell, I cut a 2" section out of one and STILL had to pound it 30 times with a BMF hammer. So don't fool around with slide pullers and all the other tricks. If you have to replace the passenger side cv axle, get a replacement engine mount/carrier bearing from a junkyard or buy one on eBay. I found one for $87.00, worth every penny. Next time, even if I had to buy a new one from the dealer it would be worth it. Heating the bracket with a torch and using an air hammer is a joke. That bracket laughs at an air hammer, slide hammer, torch, the stupid axle popper tool, chains and anything else you throw at it. Do yourself a favor and just replace the damn engine mount/bracket and be done with it, especially if you're doing it with jack stands.

@StephenDanielAddeo 6 лет назад

If it has the little 12mm bolt in the bracket, take it out and force a thick penetrant into it. Then re-tighten the bolt. Keep doing this until you see penetrant ooze around the edge of the bearing. Then you can do this without cutting anything and with bearing support mounted to the block. It's kind of like using paper to eject a pilot bearing.

@Questchaun 6 лет назад

Stephen Daniel paper trick is genius!

@briansmobile1 6 лет назад

That's brilliant! I'd love to try it on the next one. When I first started reading, I thought you were talking about removing the 3 carrier bolts. I face palmed and then heard you out anyway. Glad I did!

@Borgschulze 6 лет назад

When you got the bearing out, and I saw that hole in the carrier, I was thinking a similar thing.. maybe he could have put grease in the hole and hammered something in to push it around, but then again, it's already rusty and seized in, and you can't really force the lube around to the other side.

@StephenDanielAddeo 6 лет назад

briansmobile1 lol thanks. It works. If it's really really bad then you might be doing it your way anyway.

@reneneron2971 6 лет назад

I've also read that heat and beeswax works well. Heat the part, turn the hole so that the wax won't run out, fill with beeswax (heat will draw it in), remove CV carrier bearing from carrier. You do not need to heat it nearly as hot as you did. Many home mechanics don't have a plasma cutter, which has other dangers, and you're at a point of no return if you start cutting and fail.

@rockchild5012 3 года назад

I was having the same issue on my rx400h. NY salted streets and living by the ocean made it worse. I tried heat, air hammer, 3ft prybar, slide hammer, my neighbor even came with his jack hammer. It was not budging an inch. I ended up cutting it off with a sawzall, had to also cut that canister off too to get to the bolt on the bracket. After I took it off I still couldn't remove it from the bracket. I was so frustrated I just went to the dealer for a new bracket. If you live in an area with bad winters or sand, be prepared when you take this project on. If you try for an hour and can't get it to budge just cut it off, don't waste days like I did trying not to go the hillbilly route.

@Josh.me223 22 дня назад

You just got to remove the bolts and seal on the carrier bearing bracket. Removing the seal after removing the bolts is crucial. I thought mine was free and it wasn't. Got the seal broke and bam! CV axle slid right out. After you get it out, use a torch, pb, and a sledge. Just clean it after

@johnferguson7235 6 лет назад

1st Law of Changing Axles : Show NO MERCY Chant "You are metal... I am man.... I will win."

@franciscoromero3011 6 лет назад

I've been a subscriber of your channel for a while already. I love your videos and the way you talk on your videos or describe the whys.. is actually very professional. No profanities nor insults. Along with Charles at S.M.A, Chrisfix, Eric... (whom I miss). Keep up the good work and good videos. My hat's up for you.

@briansmobile1 6 лет назад

Thank you!

@daylbrinkman 3 года назад

I took out the exhaust and then was able to get my grinder in there.

@leoashrae4199 6 лет назад

I've done quite a few of these, mostly Avalons and Highlanders. When I get a stuck one, my Sawzall and a Lenox Laser CT blade goes through the axle like butter. I believe I had to drop the exhaust on one or two, but I don't remember exactly which model and year. Great video!

@VeryPersian 5 лет назад

Unlike others, I agree with your approach. As I have become older, I refuse to fight rust/corrosion as much as possible. Cut the axle, press it out on the shop press. Don’t have a shop press? Take it to the closest garage/shop and pay them $10-20 to press it out. Don’t waist time. Beating on it in situ is not without risk of creating new problems. Keep it classy.

@johngreene1537 6 лет назад

I cut a slit on the carrier bearing bracket and use a pry bar to wedge in it. It breaks free and slides out. If you order a Toyota one it comes with the bracket

@stefanczechorskidds8435 6 лет назад

Nice!!

@Rob-kv3ry 5 лет назад

@@stefanczechorskidds8435 Coming with the bracket is definitely a plus. Saves people a lot of trouble. Upon replacing the pass. side on my 05 camry, I put some nickel antisieze in the housing so the next job won't be trouble.

@johnshirley8184 6 лет назад

I just heat the bracket with a torch then hit the axle with the air hammer and it usually comes out .

@zacharyingalls1910 3 года назад

Air hammer is how I do them as well

@jaycarl1562 3 года назад

I'm sure he tried

@ozzstars_cars 6 лет назад

Without cutting the axle that seems to be a small nightmare. Nice fix Brian

@briansmobile1 6 лет назад

Thanks!

@ExtremeRecluse 2 года назад

Buy a new bracket

@ScubaCat3 6 лет назад

I just blasted a longer bolt into that bottom hole with my harbor freight electric impact after taking out the little one that holds it in place. It busted the bearing into pieces right in there, and I then just popped it out with a prybar. That rust is brutal.

@TheOutwiththeold Год назад

did this trick today here in Illinois , worked well.

@charlsseal7273 6 лет назад

Oh boy. A few weeks ago I tried change my passenger cv axel on my 2008 camry v6. (Same engine) and I ended up putting it back together and bringing to my mechanic who had the car on a lift and was able to whack whack it out. What a nightmare.

@datz_nice_805 Год назад

I had same problem I just air hammered the bearing.

@NamesAA 6 лет назад

Been there done that. Stupid Lexus/Toyota! Honda does this same setup so much better.

@wenbiaoliang 6 лет назад

I just removed a passenger side drive shaft on a Scion tC, with MANUAL transmission, the carrier looks similar, with 3 bolts to the engine, but it is a 2 piece design, with 2 smaller bolts connecting the two, so I just needed to take out 2 smaller bolt, and the carrier came apart, and I can slide the drive shaft out. This ES350 design is bad.

@HondaSolutions 6 лет назад

I did this on my ES300. Had to use a grinder to cut the axle to get it out. I’ve seen people use a slide hammer on the far end to get them out. It was a big job to get that axle out. It’s not a small feat. Once I got the axle cut, I was able to get the motor mount out and hammer the axle out.

@justinshelby5908 6 лет назад

yea i had to same thing on a camry axle seized in the Carrier cut the axle out with a 4 inch straight die grinder

@lakegreer9885 6 лет назад

GIT R DONE!!! Loved how your horns came out at the end when skiing }:-)~

@carlmiller1034 6 лет назад

Amazing fix Brian! It's so great (and satisfying) when a creative , albeit destructive, solution works! Reminds me of your CV-Axle puller tool. Great comment with follow-ups by Stephen Daniel too!

@mannys18s 6 лет назад

Lexus tech. These can be a b***.

@ManicMechanic007 6 лет назад

Had this same issue with a V6 Camry. Winning always feels good. Way to go Brian!

@briansmobile1 6 лет назад

Thanks buddy!

@willhikearizona 6 лет назад

I saw episode 3, it was really great to see. Those guys after you talked about your charitable foundation with passion, they were all like give the money to Brian's. It was very touching.

@briansmobile1 6 лет назад

That really touched me. Just awesome.

@ozarklife9996 Год назад

2019 I changed the motor mount on my 1997 Avalon where the carrier bearing run through it. Had to beat it on with a sledge hammer. 3 years later the boot tore so I decided to change the whole axle. Damaged the first one from rock auto so I tried to get an oem they said a year out so I got another after market on from autozone. It lasted 1000 miles and came apart. Had it towed to a trans shop. They put an o'Reilly gsp axle in and they blew out the seal on the carrier bearing. Finally got an oem axle and their mechanic drove the hold down bolt into the bearing. So they refunded my money and I purchase another axle. Number 5. I'm going to slightly clean out the motor mount so it doesn't need to be beat on so hard. Your video shows me that it doesn't need to be so freaking tight. Wish me luck.

@davidhimmelsbach557 8 месяцев назад

I ran across The Air Hammer Vibration technique. Google cv axle Toyota Sienna 20215. One uses vibration applied perpendicular to the axle -- directly upon the carrier. After 50-seconds, the axle-bearing assembly will 'walk' right out of its carrier. (!) You have to watch the video to believe it. Be sitting down.

@condor5635 5 лет назад

Great job Brian! Love the bonus footage! You'd be a fun guy to ski with I am sure. I am doing my axles this next weekend. Went to a Toyota stealership for an alignment after doing control arms and tie rod ends came back home removed tire week later and the CV joint boot was totally blown out grease everywhere on passenger side. Make your own assessment - 200k miles/15 year old vehicle, never replaced axles, photo of axle and boot area being fine the morning of the alignment job as I finished my work on other items and all the sudden the boot is blown out. Then I looked at the multi point inspection sheet and I see axle with a 'will need work in the future' checked off. Now granted, I should have replaced them probably when I did control arms but that dealership definitely made that boot break when they were working on it. Also, not one of the alignment bolts were moved since I marked their position with paint. Alignment was not too far off to begin with but how would you align a car when those have not been loosened? Thanks again! Great work

@Jumabay 2 года назад

If it’s Toyota you don’t need to replace axle ever. I owned camry prius lexus sienna all of them are with over 240K miles. Even prius was 425K mile never replaced an axle 😁

@joshuacraig2331 6 лет назад

I had the same problem. Used a carbide sawzall blade to cut mine and remove it.

@1970sRetro Год назад

“You can’t wiggle it away from the pins.” Oh yes you can. I spent 3 hours messing around under that Camry (I have no lift) before I pried it off those pins and pulled it right out. So far no sign of damage to the transaxle. Just to see, I took a sledge hammer to the axle to see if I could free it from the bracket. An hour later it was free. It was like it was welded. It banged up the bracket badly. Don’t waste time doing that. Buy a new bracket - about 60-70 dollars. This replacement was a bitch!

@surfyogi 2 года назад

There is another video on YT that shows putting a longer hi-grade bolt into that carrier bearing ring, and overtighten it, to break the carrier bearing RING, and that's how to get them out without having to cut it. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-hW4gG_3p-dQ.html

@WilliamSymionow 3 года назад

Plasma? You caveman! 60 seconds with a sawzall. If you think the Plasma was easy, the sawzall will shock you. Get the 6" steel demon blade. I couldn't believe how fast it went. Terrible design toyota. But you got it done!

@g6qwerty 6 лет назад

The axle on my acura Intgera separates where it goes into the the carrier bearing but I can remove the bolts too with out the axle being in the way, and it has a actually seals to keep the dirt out of the carrier bearing. Though the two axles half did rust together so i had to remove the whole thing and hammer it apart.

@dharmi44 6 лет назад

Auto manufacturers new business strategy, “ we build cars no one can repair, coupled with built in obsolescence!!!”

@jeffro4kag206 9 месяцев назад

Why do I always watch a great video 'after' I jerk around with this thing for 3 hours trying to pull the right cv axle out of this 06 Sienna?!

@evilwillieg 5 месяцев назад

This is the craziest sh!t I’ve ever seen in my life. I’ve changed this driveshaft 100x+ and have never had to cut one apart to get it out. I do not understand why this had to happen…

@davidsanderson5466 9 месяцев назад

What is up with these SHITTY axles that Toyota is putting in their cars? Don't have the problems with ujoints.

@stevanrose7439 Год назад

That’s the best plasma cutter I’ve ever seen the sparkle ✨ goes down and goes up. Did it come from harbor freight. Asking for a friend.

@spelunkerd 6 лет назад

I had to go to episode 3 of the pull a part challenge, evidently I missed it. It brought a tear to my eye, too.

@miguelsalazar3239 8 месяцев назад

Ive done the passenger side axle twice nyself, and they slide right out once the clip ring is unlached. The carrier can be removed and replaced if its ruste stuck.

@SeanBZA 6 лет назад

Looks like the ends on the tube are friction stir welded onto there, to get the hollow rod with the machined ends. The rust at the ends is a good indication of where the stir weld is.

@SgtSabotage 6 лет назад

Hey Brian, Nice job! A trick for the Anti-Seize. Add some synthetic oil in a 1:1 ratio stir the 'clay" off the bottom of the container and next day shake it like it owes you money. Better than new!

@briansmobile1 6 лет назад

"I WANT MY MONEY!!!" lol

@SgtSabotage 6 лет назад

Lol!!! That's the way!

@joridd 4 месяца назад

I heated and soaked bearing with pen oil then used air chisel to blast bearing out of the bracket after taking retaining clip and retention bolt with rubber dot in it did it in the vehicle with rest of axle intact came out pretty easy with air chisel

@jacobcarroll715 4 месяца назад

If you gotta cut it, use a a carbide tipped saw on a reciprocating saw. Way less heat and it cuts through it like butter

@wyattoneable 6 лет назад

Led Zeppelin T shirt, check. Ron Paul poster, check. Car guy, check. Pilot, check. I think we could be good friends. :) That was a clean under carriage to work around too. Nice to have a guest in the shop once in a while.

@briansmobile1 6 лет назад

Heck ya man!

@pcnepal 6 лет назад

The oem tube has a much bigger diameter = bigger torsional stiffness.

@tomlew2007 Год назад

Good video.. I've done so many of these and found that cutting the axle (and sometimes replacing the carrier) is the easiest way. If you don't have an access to a torch a carbide tipped sawzall blade works just as well

@briansmobile1 Год назад

Thanks

@jotu173 Год назад

Thanks for the VERY unique video. There is a tool that is SPECIFICALLY made for this (needs a slide hammer attached to it) and will put a link at end of comment. A few other things, I think the reason it was SOOOO difficult to hammer out was probably because you cut the pipe with torch (heating / expanding the pipe & bearing the most while the bracket remained cooler... the reverse of loosening it). I thought that the pins were weird too but think after watching that they are there (in anticipation of this issue) to support and make sure the bolt threads do not get destroyed if any pounding is done to remove the axle. Also, I saw on another video where a guy wrapped a "tie down" around the axle between the bearing and CV and ran the strap through the center of the hub (putting the ratchet mechanism outside the hub. Then he simply tightened the tie down against the still attached hub and it (the rusted carrier bearing and axle) simply popped out after some ratcheting. On another, a guy just used a chisel and a hammer against the trans side of the CV (and MAYBE a little on the bearing to???) and the rusted bearing came out after some "persuasion". Here is the tool SPECIFICALLY designed to make this easier (it can be rented for free too). www.oreillyauto.com/detail/c/evertough/tools---equipment/rental-tools/brake--tire---wheel-rental-tools/749f067e140e/rental-tools-evertough-front-wheel-drive-axle-puller-adapter/ren1/67102/v/a/28868/automotive-car-2008-toyota-avalon

@trevorj203 Год назад

I tried that slide hammer for 3 days it would not budge

@SeorgeGoros 7 месяцев назад

Could have just punched the little groove on the inboard housing with a chisel and had it out in 5 min but this works too

@notiratskie8955 2 года назад

Thank God a solution for me... thank u so much for posting this, I thought my idea was insane before see it actually happen...

@briansmobile1 2 года назад

You're welcome! Thanks for the feedback. I could use that today!

@stevanrose7439 Год назад

Oh I see I watched it a couple of times and it makes a difference which way you rotate the tire.

@throttlebottle5906 6 лет назад

noooo, my core charge buddy! :))

@droy333 6 лет назад

Bloody neat trick putting the sparks back in the metal haha

@briansmobile1 6 лет назад

I couldn't resist. Looks cool huh?

@droy333 6 лет назад

Haha yeah mate!

@HUBBABUBBADOOPYDOOP 6 лет назад

Trans in neutral. Electric impact on axle nut (tighten). Spin wheel/shaft, while using= A) SawzAll with carbide blade, or B) Oxy/Acetylene blow torch, to actually expel the kerf, not let it melt back in. You looked Evil AF with the light under your face, *@**0:25* like a zombie Hagar The Horrible Mechanic. LOL

@WayneCook306 Год назад

What the hell are you doing, I don't think you know.

@BruceLyeg 6 лет назад

I'm not gonna criticize the way you did it, because you got it done. I will criticize your singing though... sheesh! You should warn a guy before you start warbling away! lol Thanks for the video,

@condor5635 5 лет назад

Toyotas/Lexus have a rubber plug (you see it in your video at 10:07) that pushes against the outer bearing ring which keeps the bearing from completely rotating in the bearing housing. The 14mm bolt presses this rubber plug against the outer ring. There is NO metal (bolt) to metal (outer bearing ring) contact when bolt is installed in the bracket. No one ever mentions this rubber plug or shows it. Might not even have realized it was there because like in your video it remains in place. My recent experience with this rubber plug is that it really needs to be replaced when doing this work. Mine was not flush with the inner surface of the mounting bracket when the bolt was tightened up and bottomed out on its flange. Therefore it I were to reuse it it would not be able to perform its function - keeping the entire bearing from rotating in the mount. I suspect over the years of it being compressed it basically lost what pressure it had when the bolt is tightened. It's function is probably less and less important as the bearing seizes up in the bracket over time anyway. This is an important detail one might miss when doing this work. I did my axle using a slide hammer and 2 jaw puller which I will post more about very soon. Nothing else worked and I don't have a torch! Worked great but make no mistake, people need to plan on this job taking longer than expected due to this bearing and its removal especially with Toyotas and Lexus. As usual great video Brian. Thanks for posting.

@greasyhandsauto-shaunbutte9726 6 лет назад

Great work and you were able to save the core!

@briansmobile1 6 лет назад

Thanks. The new axle was new, but I always send in the old one anyway.

@jonnycooper4873 Год назад

Could’ve just popped the clip out it’s pretty easy

@randomgamer-st1ie 2 года назад

FYI, just had a seriously siezed carrier bearing on a 08 Solara, same exact setup. Took 2 people, one air hammering with a long chisel bit on the back of the bearing through the opening between the exhaust pipes, and the other with a huge masonry cold chisel and bfh beating on the axle just past the bearing. Either one wouldn't work independently, not even with heat. But both at the same time tamed that bitch. No cutting required. Hope this helps anyone reading it.

@jeffro4kag206 9 месяцев назад

I could not believe when I got out the three bolts on the bracket cuz I used a belt sander where I can get to that one that's almost impossible and then to my dismay it was sure enough hitting the axle and it wouldn't come out all the way and then there were these lineup pins on the bracket that caused me some frustration only then did I watch your video I don't have a plasma cutter but I have a Sawzall! You know us men folk hate to ask for directions unless we're really really lost!!! Thanks for the video. 06 sienna job that i thought would take 2 hours!

@arnoldmadela1574 4 года назад

I have 2009 camry. Both axle boots broke. I had the same issue with the passenger side. Was a pain. I went to a junk yard here in Hawaii and found a match already removed and just sitting on the side waiting for me. Pounded out the axle and paid for the brace or whatyamacallit. Did not want to ruin the original, left it on the car until I had a replacement. Installation of new axle was a pain. But, got 'er done. Oh, I have the original brace in my trunk.

@JCee-fk4bd 6 месяцев назад

I used a sawzall to cut my axle, went really easy

@theadventuresofjavier8698 6 лет назад

Brutal. I did one on a 04 camry. I couldn't get the bearing out of the bracket. Boss had me order one from the dealer. I normally don't see such rusted on parts here in California but this car came from new jersey. I need to stop complaining about California. I can only imagine dealing with rust issues every day..good job there big guy

@Rob-kv3ry 5 лет назад

I got a replacement carrier bearing housing from the salvage yard. I have an 05 camry 2.4 and I got the housing off an 09 camry 2.4. It came off pretty easy, but it would not budge off an 06 I tried to retrieve a housing from.

@joelrunyan1608 3 года назад

That carrier bracket costs like 40 bucks new. Definitely shouldn't have spent 3 hours salvaging it

@jayrenner7565 3 года назад

Air hammer. 10 minutes, tops.

@jojoskunk 6 лет назад

Done that to a Chevrolet Cobalt SS and the jakeshaft was seized in the axel shaft. Tried everything i could do to split it to change the similar jakeshaft support bearing. Had to bring it to a shop. They have put 25 mins to try with better equipment. Try explain that to a client. hahahaha

@timothy5974 5 лет назад

well, my 2007 avalon was suppose to be a simple passenger hub knuckle change. guess what ? while removing axle nut, axle threads were boogered up. This means I have to do this job. Brian, thank you for your video. I used a die grinder instead of the plasma cutter. It took 4 hours and a severe beating of the bearing out after it was removed. totally messed up that they put pins in the carrier. just whipped my butt tonight. heading to nappa for a new axle tomorrow morning . thanx .

@Nvp8985 6 лет назад

Solid improvisational skills! Great work.

@ptbruiser2243 3 года назад

Next time remove the pass MM and pull the engine away from the firewall gives you just enough room to get it out. just had the same prob on my sons 00 celica GTS

@mitchlopina 5 лет назад

Going through the same thing on a Solara. I was thinking cutting it is the best option. I don't feel so bad now. Nicely done. Going to let it soak overnight with PBlaster, and beat it like a child molester. If it doesn't break loose, I will get the shovel(great idea), and the red wrench. Terrible design.

@sweetwilliam49 6 лет назад

Don’t quit your day job. I’ve own Toyota’s and I own lexus. I can honestly say I’ve had a lot more trouble out of the lexus than the Toyota’s. Go figure

@jianbinchen2881 Год назад

i doing the same thing but use cutter.

@VENUEATHENS 3 года назад

Hi there what brand cv axle did you use for the replacement, and what company do you recommend going with that will last because this is fairly big job to do over again

@davidgreer4790 3 года назад

My son’s 1996 Camry has the same bracket. I wound up cutting the axle with a grinder.

@bygonebob 6 лет назад

Why go through all the pain when you can just pry that bracket loose from those dowels like what this guy did in this video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bzkywfOCVoU.html?

@colchronic 3 года назад

You know you can just sawzall the driveshaft right?

@tedbonbrake1967 6 лет назад

Obviously everyone needs a plasma cutter in their toolbox. I long for the days when a big effing hammer was all you needed...

@jab-pt3pc 2 года назад

Great video. I had the same issue with mine. It was stuck solid. I beat on it with a 3 pound mallet and a long bar for about an hour. I then put an air hammer directly on the back side of the bearing and it popped out in about three minutes. Obviously it destroys the bearing but I was replacing the axle anyway. Just another method to try for us who don't have a cutting torch. Thanks for the video.

@JamesLee-oe7mt 6 лет назад

I have to do this job soon...same car, inner boot leaking. Would it possible to separate the inner joint while still in the vehicle? Then I wouldn't have to mess with that bearing and carrier... Is there a snap ring in the inner joint or should it just pull apart once the boot is unclamped?

@stefanczechorskidds8435 6 лет назад

Talk about bringing a Tank to a gun fight! It would have been interesting to see how far you would have gotten with a sawzall. (?) Need to "loose" those pins (for the next guy)!

@lilliy262 6 лет назад

Awe hell. Got the cv axel out. Now the bolts are striped in the motor mount. What a day. Working with minimum space. Whooooo.

@thatmechanicguy8773 6 лет назад

Cutting the axle is unnecessary. All you need to do to get a Toyota axle out of the bearing bracket is hit the bracket with an air hammer while a buddy puts a pry bar on it. Once it’s out, you clean the heck out of the bearing seat in the bracket and it’ll slide back together nicely.

@Jim-tz9lj 6 лет назад

Why run the video backwards when you're cutting? It just makes it look goofy.

@condensermike 4 года назад

I have had that Black Crowes song in my head for days now even before watching this. Spoooooky....

@nelsondavis4310 2 года назад

I just did that job on my Sienna van, used a sawzall and air die grinder. I cut the bell part off with a torch and then pounded it out in a large vise.

@briang804 6 лет назад

After taking the snap ring and the 14 m bolt with rubber end out, put your air hammer bit on the carrier and put your prybar between the carrier and the inner joint of the axle while the axle carrier is still bolted in the vehicle. At the same time hit the carrier with the air hammer and pry. Sometimes you need a big pry bar but one person can do this job.

@CHARLYNNE123 6 месяцев назад

Took me 1 day to put clip in

@mr.weaver2682 6 лет назад

I work for Toyota Motor Company. The dowel pins on the engine block for the mount are only there to make production easier.

@marcricker2570 3 года назад

love you man ! thank u! :)

@claudesmoot1880 6 лет назад

No wonder it rewelded it'self you turned it the wrong way and it made the sparks go back into it.

@rockiemountin7535 3 года назад

Looks like a good way to get it out but probably not the best thing for the seal, and that car is super clean underneath you must be in the Southern or Western states here in the Northeast area everything is rusted together you guys got it much easier in the warm states