Transit Custom how to replace front brake discs and pads replacement due to brake judder 2012 on

Подписаться 8 тыс.

Просмотров 41 тыс.

50% 1

Thank you for watching my how to replace front pads and disks on a transit custom video, tools and tightening torques are listed below.
Parts used in video
Mintex Front Pads ebay.us/s1j7fP
Brembo Front disks ebay.us/XVOJWT
Tools used
Spanners 15mm and 21mm
Pliers set
Screwdrivers
1/2 inch breaker bar
1/2 inch deep sockets 13mm and 21mm
3/8 flex ratchet
3/8 inch deep sockets 13mm and 17mm
Soft dead blow hammer
3/4 inch 36mm socket
Long torx t50 socket
3/8 torque wrench
Wire brush
Scraper
M10 x 1.5 bolt 100mm long at least
Tightening torques
Wheel bearing housing to hub/ strut bolts 53Nm
Break disk to wheel bearing hub 30Nm + 90 Degree Angle
Driveshaft nut 250Nm then rotate 5 times then 500Nm
Brake carrier to hub 270Nm
Calliper to carrier 60Nm
Road Wheels 200Nm
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional charge to you! Thank you for supporting this channel
Thank you for watching please like my video if it helps and subscribe for more videos, also please follow me on Instagram to keep up to date with what's going on on my channel @ Martys_workshop

Опубликовано:

1 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 132

@captspaulding987 4 года назад

Cheers mate, this is by far the best video on this subject on RU-vid. I wasn’t confident enough to do this on my own until I found your video. Nice one Marty

@Martysworkshop 4 года назад

Thank you for your feedback, i really enjoy making these videos and hearing comments like this make me confident that i am doing something wright, thank you again for watching.

@captspaulding987 4 года назад

Is the same job on the back much different?

@alexmarquetti1725 2 года назад

Please DO NOT let the caliper hang by the hydraulic hose!!!! That is a No No NO!!! Thanks for the vid

@Martysworkshop 2 года назад

Thank you for your input.

@georgeshaw6207 6 месяцев назад

Superb video. Best on RU-vid !

@Martysworkshop 6 месяцев назад

Thank you I also have one on rears cheak out my playlist

@arthurcator5246 Год назад

I'm new to this. Where is you description for torque settings? Great video.

@Martysworkshop Год назад

If you click on more under the title when the video is playing, thank you for your feedback

@julianfrombrisbanesolarrep1228 Год назад

I was about to tackle this tomorrow but I’m glad I watched your video - looks like I better grab a longer TX bit! Thank you for a very informative, easy to follow video.

@Martysworkshop Год назад

I'm glad my video could help ☺️

@kenlarman4252 3 года назад

Great concise & well explained video 👌 I’m looking to purchase a Transit custom at the moment so came across this while looking for information on their common fault, do you know what the best engine version to go for around the 2014 - 2016. Watched all add’s so you get your Pennies 👍 “Liked & Subscribed”

@Martysworkshop 3 года назад

Thank you for your support ken, i own a 2013 limited 130 i couldn't be happier with it, i was advised to stay away from the 150 model when i bought mine as they have more problems, but it is the same engine just tuned up more so i can't see a problem. I Guess its more on the driver. Know i do know the newer ad blue engine (new shape) is having a lot of issues so i would stay clear of them. Hope this helps

@alessandrobertolo585 8 месяцев назад

Top video. Quick question, which tool did you use to retract the front caliper pistons? Thanks again.

@Martysworkshop 8 месяцев назад

I just use a large flat head screwdriver

@alessandrobertolo585 8 месяцев назад

One more question Marty. I see videos where people when pushing the caliper pistons back they open the bleeding nipple which is connected with a little pipe to a plastic container. What do you think about that? I am concerned that opening the bleeding valve you can get air in the sistem. Thanks for your advice.

@Martysworkshop 8 месяцев назад

I have never done it tbh, I just push the pistons back with a screwdriver. I would also be concerned of air getting in the system just to make it easier to push the pistons back.

@3161tc 3 года назад

Brilliant Description thank you

@Martysworkshop 3 года назад

Thank you for your feedback

@bobmuir5811 Год назад

This is a brilliant video thank you very much, I have just finished doing my discs on the van. There is also a great method for getting the disc off the bearing by Bodgit and leggit garage. No hammering required, worked a treat. Thanks agin.

@Martysworkshop Год назад

I'm glad my video could help ☺️ thank you for your feedback.

@yetiandbean9223 4 года назад

I wasn't going to say anything as for the most part I was learning from you, BUT you did ask for advice at the end LOL so; I worked for a torque tools manufacturing company (Norbar) and they drilled into us that clicking multiple times on the torque wrench actually increases the torque every time due to the function of the torque breaking device - every time it clicks beyond the first one is increasing the torque. They showed us this on a torque measuring device with a normal click style wrench and its interesting to see how much it goes up - its a bit like an impact hammering action. So to get the correct torque you should click it once and trust it or, if you really must, a second click only, no more. And if you are doing a bolt circle best practice is to click once only first time around, and then give each bolt just one second click to double check nothing was seated oddly the first time round. Cheers for the help you have given me!

@Martysworkshop 4 года назад

Thank you for your feedback, i have never given it a thought but it makes complete sense! Thank you again for this comment i will definitely give this a thought as i use torque wrenches every day.

@zteveh 2 года назад

Great video, I have the same juddering under braking. What causes that juddering? as this will be my 3rd change of discs/pads in 25k miles of gentle driving and braking due to juddering. Tempted to DIY it myself. I have the 9 seater Tourneo.

@Martysworkshop 2 года назад

Mine warped due to being worn thin. Only advice I can give is use a good make disks, I use apec or mintex, most factors offer a cheep or premium brand and garages tend to use the cheep to keep cost down. Thank you for watching.

@nickayivor8432 Год назад

Good Morning 🙏 🌄 thank you for sharing it God bless you and all your family around you 👍 Take care and have a great day From Nick Ayivor from London England UK 🇬🇧

@Martysworkshop Год назад

Thank you soo much for your kind feedback nick, I'm glad my video could help, 😊

@mattquinn6682 4 года назад

Perfect video followed this today and was super simple thanks 👍

@Martysworkshop 4 года назад

Glad i could help, thank you for the feedback

@beemac4515 2 месяца назад

After watching literally 30/40 videos looking for torque settings and procedures etc I came across your video and wish I found it first, It is the best on RU-vid, Thank you.

@Martysworkshop Месяц назад

Thank you for your support

@mathewmorris1469 3 года назад

Great vid. Problem I’m havin is the drive shaft won’t knock through, it’s stuck and I’m welting it! Any tips on solving this? Thanks. Mat

@Martysworkshop 3 года назад

I would try a puller on the flange witch pushes on the shaft. If that fails you may have to remove the complete hub and shaft and put it in a press, i have had to do that before tbh, hope this helps

@JKGriffithsChimneySweep 3 года назад

Good video, had 1 torq socket snapped in the head off bolt torq bolt!! painful Experience could not get the snapped socke6out spent hours and a fortune on drill bits, got there in the end!!

@Martysworkshop 3 года назад

Sounds like a painful experience, glad to hear you sorted it tho, thank you for supporting the channel

@topdarts6015 4 года назад

Just want to say a big thank you for the vid . I’ve just finished doing my front discs and pads . Followed step by step and it was bang on . Only Fock up I had was one of the stretch bolts snapped when removing the disk . £1.50 for a new bolt from the ford garage so happy days . Cheers 👍🏻

@Martysworkshop 4 года назад

Thats brilliant and thank you for your feedback

@DirectGecko 3 года назад

Massively helpful guide lad but after following it to the dot, one thing I'm wondering about, copper grease for the pads ?

@Martysworkshop 3 года назад

Thank you for your support, yes copper grease on ether end of the pads where they slide is good to stop them sticking in my opinion but some people think it is a bad thing so i left it out of this video

@nickmactools 3 года назад

Hi Marty, good to see you are still turning wrenches the right way! Think I spotted some of the MAC Tools I sold you years ago, lol. Keep the vids coming!

@Martysworkshop 3 года назад

Hay nick cheers mate yeah still got most the tools i had off you mate they all going strong. Cheers for the support mate

@jdggames 2 года назад

He said he’s going to clean the flange off with his wizzer 😂. Great informative video. Really helped a lot

@Martysworkshop 2 года назад

Lucky van!! Thank you for your feedback.

@Torrrrrrrrrr 2 года назад

Very useful video, thanks👍🏼 Please make one for rear discs too😊🙏🏻

@Martysworkshop 2 года назад

I will do thank you for watching

@Inkypinkydonkey 2 года назад

Excellent video. Thank you so much. Gonna tackle this now!!

@Martysworkshop 2 года назад

Thank you for your feedback.

@chrisduke5922 4 года назад

Can you do a video for the rear please? Followed this and worked perfectly tjanks

@Martysworkshop 4 года назад

Hello i recently did the brakes on the rear of this van but unfortunately wasn't able to get any footage to make a video, i will ask about and see if i can do one soon, but just a note it is a lot easier than the front! Thank you for watching

@chrisduke5922 4 года назад

Thanks for reply, do you need a rewind tool for the calliper?

@Martysworkshop 4 года назад

@@chrisduke5922 yes you do

@MrEnglishman6969 4 года назад

BEST VIDEO I have seen for doing a job.

@Martysworkshop 4 года назад

Thank you for your feedback, I'm glad i could help

@sezeryal 2 года назад

what's the mm thickness of discs that will require a replacement?

@Martysworkshop 2 года назад

Technical manual says 30mm is the minimum front and 13mm minimum for the rear, thank you for watching

@eddyrunip 11 месяцев назад

Hi, Just wondering whether you need to add the 90 degree angle after torquing the bearing to disc bolts as they are not new stretch bolts. I thought the final angle on the bolts is for the stretch. Would a bit of medium strength thread lock be suitable with the 30nm torque on the bolts ? Cheers

@Martysworkshop 11 месяцев назад

Your wrigh as the bolts won't stretch the same the second time but 30nm is nowhere near tight enough for thease hubs a simple rule for stretch bolts is if you can run a nut down the thread with your fingers then they are good to use again. Hope this helps

@robbiebruce2687 3 года назад

Very informative and helpful. Thanks

@Martysworkshop 3 года назад

Thank you for your comment

@smacporters9817 3 года назад

a true professional. you should have been a teacher. thankyou

@Martysworkshop 3 года назад

Thank you so much for your kind words I'm glad this helps

@ltaylor3281 Год назад

How tight is the front hub nut, I cant undo it I've bent 2 t bars already, it just wont budge.

@Martysworkshop Год назад

It's 500nm so you need to use a 3/4 bar or high torque impact gun,

@eddieash1669 Год назад

Great video mate. Some of the torx bolts are knackered on mine but can't seem to find any on the web, any ideas for suppliers?

@Martysworkshop Год назад

Not sure but you could replace them with alen head bolts as they shuld be more available. Hope this helps

@eddieash1669 Год назад

@@Martysworkshop thanks, didn't think of that. Nothings straightforward is it!!

@Martysworkshop Год назад

Not thease days I'm afraid

@Abbadon2001 4 года назад

This was a great help, and avoided me starting the job without the torx bit and a long m10 bolt, and saved a lot of head scratching! I needed to use a second bolt to get my disc off on ond side, the side where the disc was fractured thru the cooling fins....! Another tip, gas bottle spanners are 21mm on the smaller end in UK, as I didn't have a 21mm apart from that one :)

@Martysworkshop 4 года назад

Thats good input thank you for your feedback its not a bad job once you get into it. Thank you for watching

@skoprivlenski Год назад

What is the length of the M10 bolt?

@Martysworkshop Год назад

At last 100mm

@jamesborg2536 4 года назад

Great video, very useful! Thank you!

@Martysworkshop 4 года назад

Thank you for your feedback

@michaelkelderis8455 Год назад

Great vid Marty , I have a 2014 is this the same set up as yours ; Mick

@Martysworkshop Год назад

Yes it is the same, thank you for watching

@richardlemarechal199 Год назад

Great video thanks marty

@Martysworkshop Год назад

Glad my video could help.

@rizla0940 Месяц назад

Great mate Thank you 👍

@Martysworkshop Месяц назад

Thank you for watching

@darrynbird8111 3 года назад

Nice presentation, cheers

@Martysworkshop 3 года назад

Thank you I'm glad i could help

@jeffyoung8012 9 месяцев назад

Just used this video to do mine im up to un doing hub nuts as not got a deep socket till tomorrow.....this video is the best one ive found on doing this many thanks.

@Martysworkshop 9 месяцев назад

Thank you for your feedback I will be putting up a rear disks one soon.

@jeffyoung8012 9 месяцев назад

My fronts had completely collapsed. Only done 55k never seen that before in 30 years of driving!

@Martysworkshop 9 месяцев назад

Mine have warped twice since I have had it, given a bad vibration under breaking

@jeffyoung8012 9 месяцев назад

@@Martysworkshop twice blimey that's bad should get 100k out of a set of discs....I've gone for Delphi ones ....see how they do....cheers for the tutorials I've just subscribed now

@Martysworkshop 9 месяцев назад

Thank you for your support

@lewiscunliffe1051 3 года назад

Top video, best by far. Including socket and spanner sizes 👌🏻

@Martysworkshop 3 года назад

I'm glad it helps thank you for watching

@goathead53 4 года назад

Great video mate very professional.Are you based in Wales as im after a mechanic for my transit.?

@Martysworkshop 4 года назад

Thank you for your feedback, I'm based in gwent.

@pablosdelights3494 2 года назад

Has anyone done the rear disks on this type of transit custom . Is it the same process or do you need any extra tools ?

@Martysworkshop 2 года назад

Its the same job just easyer as you have no driveshaft to fight with, thank you for watching.

@toeknee6588 3 года назад

All i could see was the caliper hanging by the flexi hose!

@Martysworkshop 3 года назад

Thank you for your feedback

@garydeandeery 3 года назад

Did you take off the brake fluid cap to help push the piston in

@Martysworkshop 3 года назад

No the cap will vent to no need to take it off. Thank you for your question

@adriandavies827 2 года назад

Where are you based?

@Martysworkshop 2 года назад

Hello Adrian, I'm based in South wales.

@adriandavies827 2 года назад

@@Martysworkshop I live in Llanelli how much dose it cost to put new front disks on my ford transit custom 2016 ?

@Martysworkshop 2 года назад

I would know sorry I can do them in about 2 hours, but I don't work for a retail garage, sorry

@SeanagnewA7X 3 года назад

Great video mate. Just started doing my disc and pads today. Mines doesn't seem to have a brake pad wear sensor Also the bolts holding disc to hub are absolutely solid all the way out . Feel as if they are going to snap .

@Martysworkshop 3 года назад

Spray some wd40 or something simular, have they started to turn? If they have work them in and out a few times to get the release oil into the threads. Thank you for watching

@SeanagnewA7X 3 года назад

@@Martysworkshop Yeah they have started turning. Will try and spray them in the morning with some pb blaster and work them in and out. Cheers mate for the advice

@petereyre4097 3 года назад

Have you done the rear pads and discs yet?

@petereyre4097 3 года назад

Is it the same kinda thing?

@Martysworkshop 3 года назад

No but when they do need doing i will get on on here, they are actually a lot easier as you only have to remove the centre nut and the hub and disk just pulls off. Thank you for supporting the channel

@petereyre4097 3 года назад

@@Martysworkshop is it again the same 36mm socket for the hub nut on the rear? Thanks for your help!

@Martysworkshop 3 года назад

Im not sure to me honest but you shuld be able to pop the hub cap off to see.

@petereyre4097 3 года назад

@@Martysworkshop cool thanks. Got the job on Saturday front and rear discs and pads so i will see!

@burger_man. 5 лет назад

Great walk through video, is it the same on a rear wheel drive?

@Martysworkshop 5 лет назад

Thank you craig, the transit customs only come in front wheel drive but the larger transit couriers and previous model transit in rear wheel drive is the same setup to my knowledge but instead of a driveshaft you would have a dummy shaft in its place.

@dikhotiexe5679 2 года назад

Thank you Martyn 🙂👍👍👍

@Martysworkshop 2 года назад

I'm glad my video could help. Thank you for your feedback

@kefl298 4 года назад

great vid,i got to sort back and front on my transit before april

@Martysworkshop 4 года назад

Thank you for watching, and the rear brakes are a lot easier to do.

@cossieburner 4 года назад

Awesome vid buddy 👍

@Martysworkshop 4 года назад

Thank you for your feedback

@TOBImue1 4 года назад

Great video, thank you

@Martysworkshop 4 года назад

Thank you for watching

@WizzRacing 3 года назад

Yeah that warp rotor tire shake will wake you up.....

@Martysworkshop 3 года назад

Yeah it was a bit sketchy to say the least.

@RosarioMr 3 года назад

Hi, where’s the best place to get the bolt. No where has that size

@Martysworkshop 3 года назад

Sorry that one is stainless here is a pack of 10 for less www.ebay.co.uk/itm/METRIC-HEX-HEAD-HIGH-TENSILE-SET-SCREWS-M10-x-140MM-1-5P-8-8-GRADE-ZINC-QTY-5-/183138188373?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=710-127635-2958-0

@RosarioMr 3 года назад

@@Martysworkshop thank you

@Martysworkshop 3 года назад

Glad i could help

@topdarts6015 4 года назад

Top man ! Nice one

@Martysworkshop 4 года назад

Thank you for watching