Troubleshooting Dishwasher Fuses and Control Boards - Whirlpool - Maytag - KitchenAid - Amana

Просмотров 15 тыс.

% 145

Dishwasher not working? Discover how to locate and test fuses in your dishwasher with our detailed guide. We'll explore fuse and control board locations and show you how to use a multimeter for testing. The fuses protect the load circuits of the dishwasher. If one of the fuses blows it can cause the dishwasher to not heat, not wash, not drain, not fill with water, not power on, and more. This troubleshooting guide applies to Whirlpool, Maytag, Jenn Air, KitchenAid, Amana, Kenmore, and more. Find the problem with your dishwasher and get it fixed quickly!
Purchase parts: partsdr.com
Table of Contents:
0:00 - Intro
0:18 - Where To Purchase
0:26 - Reasons
0:38 - How to Remove
4:31 - Locating Model Tag
4:42 - How to Install
8:03 - Outro
Dishwasher shown in video: KDFE204EBL2
Appliances break, but repair & maintenance doesn’t need to be difficult. Find the right part for your job at: partsdr.com/
We sell OEM appliance parts for Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, Frigidaire, Electrolux, Tappan, Westinghouse, Kitchen Aid, Jenn Air, Bosch, LG, Samsung, and more.
If you found this video helpful, please click the thumbs up button and leave us a comment below.
Connecting with us:
Facebook: PartsDr
Twitter: parts_dr
Repair Forum: forum.partsdr.com/
Blog: partsdr.com/blog/
Subscribe to our RU-vid channel: ru-vid.com
#PartsDr #MakeAppliancesGreatAgain #Whirlpool

Хобби

Опубликовано:

15 окт 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 40

@PartsDr 4 месяца назад

Did this help you fix your dishwasher? Let us know what symptoms and error code(s) you were experiencing. Learn how to read the error codes in diagnostic mode here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3sX9hjGb-iQ.html

@uhklem 2 месяца назад

Very clear narrative and step-by-step images and instructions. Thank you!

@MrYayoperez 4 месяца назад

Excellent instructions. Thank you

@PartsDr 4 месяца назад

You're welcome! Did you find that you had a blown fuse?

@toma5153 2 месяца назад

I misplaced the tech service sheet for my Kitchenaid dishwasher. Any way to find a copy online or buy another one?

@Mdeil20 4 месяца назад

My fuse blew a few months ago and got it replaced and since then it was fine. A few days ago it tripped again so I replaced it and ran it but maybe 20 minutes into a cycle it opened again. Do you think it may be a clogged filter that is causing the drain pump to work harder and blow the fuse? Guess it could be a bad heating element too.

@PartsDr 4 месяца назад

It can be tricky to figure out which component is bad and putting extra load on the circuit. Let us know what you find as the solution.

@jjf825 Месяц назад

The drain pump doesn’t pump the water out until I push in the middle of the door. Already replaced the drain pump, cleaned the drain hose and filter really well. Getting an F8E2 error code. Whirlpool WDTA50SAHZ0. Any ideas?

@PartsDr Месяц назад

Check the door latch and door strike since you are describing pushing on the middle of the door. Also, check the things shown in this here ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Q5-rLuFevHE.html about troubleshooting a dishwasher that isn't draining.

@kjhnsn7296 17 часов назад

My Whirlpool dishwasher heating element will not shut off once the dry cycle is completed. I tried resetting the control board by turning off power at the circuit breaker. The issue remains. Anyone have any insight to potential cause?

@PartsDr 14 часов назад

It could be a relay sticking closed on the control board. If this happens, the control board will need to be replaced. Also, a short in the wiring harness could cause this type of problem.

@kjhnsn7296 11 часов назад

@@PartsDr I changed out the control board with a used one. That appears to have resolved the problem, BUT to your point, when I was changing it out I noticed the large wiring harness did appear singed... struck me as odd... Will see if I can find a replacement wiring harness.

@uhklem 2 месяца назад

After a pump motor burned out a few months ago, and the heating element a month later, the dishwasher started stopping right after starting the wash cycle. Looks like replacing the control board fixed the problem. The old control board showed visible signs of overheating at the pump motor power connection.

@PartsDr 2 месяца назад

Thanks for sharing!

@JefeSr 4 месяца назад

there are two fuses here, the f8 & f9. The f9 fuse appears on the schematic but I cannot identify what the f8 fuse serves. When testing the f8 fuse according to the diagram, it's open. I can't figure out what components are fed by f8

@PartsDr 4 месяца назад

What is the model number of the dishwasher?

@JefeSr 4 месяца назад

@@PartsDr kdtm354dss4

@vernonhensley4122 5 месяцев назад

SO GLADI FOUND THISVID

@PartsDr 5 месяцев назад

Great! Did you have a blown fuse?

@lloydabbington6900 9 месяцев назад

My heating element burn out I replaced it, it's still not working so is it possible I have a bad fuse?

@PartsDr 9 месяцев назад

Yes, that could be the cause, it would be worth checking.

@johnlee-wc1ky 7 месяцев назад

Dishwasher circulation pump comes on and goes off during a session. Could that be a bad control board??

@PartsDr 7 месяцев назад

It could be if the power is not being sent consistently to the pump motor.

@marissahinds 4 месяца назад

How do you test the wires going to the circulation pump? Both of my fuses are working, but the new pump I installed is not pushing circulating properly. Soap is left at the bottom of the pan.

@horsez2 7 месяцев назад

What if your service manual isnt there?

@PartsDr 7 месяцев назад

What is the model number of your dishwasher? ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-her9eShOYtA.html

@kenchow2279 3 дня назад

I have normal wash,heat dry and cancel light flashing,tried unplugging power ,replaced control board still did not fix ,touch pad is unavailable here in Canada,any suggestions or should I have listened to everyone and bought new machine part was 300 dollar no refundable 😭😭😭😭

@PartsDr 3 дня назад

Often times those symptoms are caused by a failure of the touchpad.

@kenchow2279 2 дня назад

@@PartsDr most excellent video it helped me confirm it was the touchpad where part is unavailable in Canada is there anyway I can repair that touchpad ,I took cover off it has a circuit board underneath pad quite the part no wonder it failed,any other other manufacturers part that would work,machine is 12 years old parts guy warned me just go buy a new machine and I didn’t see your video at the time and took a calculated risk which I clearly lost a new midrange machine is about a thousand dollars the control board costed 300 and it didn’t fix it now I have to hear it from my wife all my friends advance thanks for any advice😭😭😭

@PartsDr 2 дня назад

@@kenchow2279 Sorry, we are not aware of a way to repair the circuitry inside of the touchpad.

@kenchow2279 2 дня назад

Thank you for info🙏🏼🙏🏼

@shoodiemack9997 9 месяцев назад

If my power button to dishwasher wont even turn on then its probably my control board ... Right?

@PartsDr 9 месяцев назад

We never like to assume anything. Something as simple as no power to the dishwasher could be a cause of the issue.

@marissahinds 4 месяца назад

Both fuses are beeping from my multimeter test. I just replaced the pump and motor, but i am having a persistent issue of the water not circulating. Soap just drops and pools on the door and bottom pan. Do you think it could be the pump or motor wires? How do i test those?

@PartsDr 3 месяца назад

It sounds like the wiring or main control board could be bad. You can test the wiring for continuity by turning off the power and removing the wire on each end, then use a mulitmeter to test it for continuity.

@marissahinds 3 месяца назад

Welp- I did a diagnostic test and it came back with the code 5-1 for door latch. Which is odd considering we have an issue with the water flow. They're connected though from the visual in the service tech sheets- does that sound right? The wiring for the latch had a continuity test of 0.0, so it's ok. Maybe I should test the points on the circuit board? Sheesh. I'm in a rabbit hole.

@RealMesaMike Год назад

So, if the 50¢ fuse is bad, you have to toss the whole control board and buy a new one for $150.00. Nice.

@PartsDr Год назад

Sorry to bring you the bad news!

@johnspinelli6170 6 месяцев назад

Why couldn't you use a jumper with an equivalent fuse in it?

@captianmorgan7627 2 месяца назад

Just find someone who has some basic soldering capability. These look to be fairly big parts, as surface mount components go, and should be fairly simple to replace. These are cheap, easy to find, and readily available parts. (7A 125V ( LF7A ) fuses made by Littelfuse)