Tuning My 416 C6 Corvette At The Track

Подписаться 2,9 тыс.

Просмотров 3,1 тыс.

50% 1

2008 4lt base LS3 based 416 is set up for boost, trickflow gen x 255 heads (unported) 69cc chambers, BTR custom grind cam blower cam, BTR Valve springs, BTR Trinity intake manifold (unported), stock ported throttle body, Wiseco dished pistons, K1 rods, K1 crank, Johnson 2126lsr lifters, ARP everything, Circle D 258mm converter, 6l80, stock 2.56 gears, kooks 2" headers, 3" xpipe to 3" dumps, vararam intake, fuel injector clinic 60lb injectors, walbro 450 pump, ati 10% UDP. Racestar front runners with M&H front runners, rears are 275/40r17 Hoosier DR2 drag radials, GM flex fuel sensor, this was on 70% ethanol, BST C6 6l80 Differential Brace.
The only weight reduction was the passenger seat removed and front skinnies. The race weight was around 3410-3420 lbs.
Tuned by looneytuned racing & speed
/ looneytunedracingandspeed
ig @looneytunedracingnspeed
pB__eQ3WBR...
#stockblocktheworld #looneytuned

Авто/Мото

Опубликовано:

6 фев 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 40

@kenm724 Год назад

I miss Fayetteville… at least Rockingham is awesome again. This video gives me some more motivation to get my Corvette going again. Hoping for 10’s in my cam-only C5.

@andrewd843 Год назад

10s is definitely possible. When hunting for a time it's all about the short track time.

@kenm724 Год назад

@@andrewd843 Absolutely. A decent converter and gears should get me there!

@burtgummerVerified 2 года назад

You're filming and sharing. That's not sucking at youtube. Thank you for sharing your content. I like what you do. Keep taking us with you👍

@andrewd843 2 года назад

Thanks! I wish I would of got more runs, but once I was in the zone I even took the gopros off the car since they were bothering me. But where I had one setup it ended up not recording right with how the frame rate is.

@burtgummerVerified 2 года назад

@@andrewd843 if I lived near you I'd pit crew for you just to get experience.

@matthewgregory6296 2 года назад

Congrats dude! You're so close to hitting the 9s.

@andrewd843 2 года назад

This is how it always goes. A few years ago, in my srt4, I kept running 12.1 12.0 12.0 12.0, then finally clicked off an 11.8 pass

@LukeWaters 2 года назад

damn, thats crazy what the tire size difference makes, great video!

@andrewd843 2 года назад

Thanks! With long 2.56 gears, the shorter tire definitely helps. All about how fast you can get into that power.

@MrVall345 Год назад

Great video! Thanks for posting. Question… what is that slight stumble in the middle of second gear, converter locking?

@andrewd843 Год назад

Yeah, that's the converter lock

@dennisrobinson8008 Год назад

sounds good

@andrewd843 Год назад

Thanks!

@89_boostedsupra 2 года назад

Congratulations on the pb!

@andrewd843 2 года назад

Thanks! At first I was just like what the hell am I going to do to go from a 10.18 to 10.17. A couple clicks on the laptop and there it was.

@89_boostedsupra 2 года назад

@@andrewd843 lol. If you try to leave any harder does it push through or try to spin? See you just need to move back this way you have a lot of ppl around here you know lol

@andrewd843 2 года назад

@89_boostedsupra it's been talked about with the wife for sure. Even if I just move to the other side of Fort bragg, it'll cut an hour of my drive. It seemed to launch best at 2000rpm, around 3000 it would push, under 2000 it didn't flash harder. But it didn't spin at all or try to. I did, however, find a vacuum leak. I thought I had one, but the car ran good, so I didn't give it much thought. So I'll have one more outing before I have surgery this month. Hopefully, a little better weather and no vac leak will help me out some.

@89_boostedsupra 2 года назад

@@andrewd843 for sure. I deliver to the Fayetteville area so I definitely understand the drive. I’m sure there are plenty of ppl around here to hang out with lol.

@89_boostedsupra 2 года назад

@@andrewd843 only thing is it’s 1/8 mile round here lol

@TylerToplovich 2 года назад

Sounds killer man chipping away quickly! What rpm you shifting at?

@andrewd843 2 года назад

Each gear and rpm were different rpm for the first few passes. I think I was going to 7600-7700 this day. If you check out my dyno video I posted last week, I ended up revving it even higher.

@TylerToplovich 2 года назад

@@andrewd843 I shift the G8 at 7000 lol 7600 would sound nasty