i updated the firmware in my H. I only get 3.2.07(A). I could not get 3.2.7. Also, i dont get the player where I can play the video from the Cgo3+ to the St16 without removing the micro sd in the cgo3+. Any help would be highly i appreciated.
I notice that Yuneec has a booth here in Melbourne Australia at our ces show on the 25th of June, will be asking if there is an updated camera in the near future for the H? I'm looking forward to the show and Yuneec
Yuneec Team, I also downloaded the firmware for the ST16. I could not get it to update. It says "unable to find install package". this is the current firmware V03.01.b18 i have. i could not update to ST16_V3.1.22.yuneec. Please help. Thanks
Hello Von, Please use a 32gb card or smaller and format card to FAT prior to installing firmware on SD card. After updating transmitter with new firmware you will need to re-bind machine and camera. Camera password 1234567890. -Team yuneec
can you help with my drone ,i just bought from some one used who assured it is working with no issues,i put a new battery in it ,it turn on for a few minutes then turned off...and refuse to turn back on ...im not sure what to do at this point i keep trying ,it simply willow turn on
Hi went through my update on the H. Website says gimbal software being installed is version 1.22, however after update H says 1.21. Is there a problem , or just a typo somewhere? Other software versions match.
Hi guys thanks for the H firmware worked a treat, I noticed that on your ST16 screen the firmware for the controller listed is the same listed on mine? does that mean I don't need to update the controller? I did download the V03.01.B18 but a prompt when I tried to update said "fail to unpack"
Update problem ! firmeware : files.zzz ! Hello I receive my Typhoon H today. I checked the updates. current version after unboxing : When i download the new firmware, i have this : files.zzz upgrade impossible… what is the problem ? same thing for the st16 upgrade. But this version is up to date… Help me please.
Hi, I updated the firmware today however after I checked only the camera version is updated, while gimbal and auto pilot ver is N/A. Is there any problem on my setup? I tried several times to update again, and results is the same.
Hello Way Home Love, After updating transmitter and machine you must rebind camera/machine to transmitter. Once bound you will see information displayed on ST16. -Team Yuneec
After update new firmware 3.04 My Typhoon H > Caribration ACCELEROMETER > Fail fail in door + out door about 10 locations i can't do it ..................... when GPS Ready > i do Caribration Accelerometer then ST16 show Gps disabled + GPS ready change to be disabled
Unfortunately RTH altitude is not adjustable at this time. WHEN HOME MODE IS ACTIVATED Typhoon WILL RESPOND AS FOLLOWS: A) When flying higher than 33 feet (10 meters) Typhoon H will maintain the current altitude, fly back to the home point, or active home point if the ST16 Ground Station has enough satellites for Follow Me, then descend vertically until it lands. B) When flying lower than 33 feet (10 meters) Typhoon H will climb to 33 feet (10 meters) while flying back to the home point, or active home position, then will descend vertically until it lands. -Team Yuneec
Hello Peter, Download update files to your laptop. Install firmware file on to a blank sd card. Insert into transmitter. If you need further assistance please call Tech Support at 1-844-898-6332. Top right corner on transmitter is camera SD card indicator. -Team Yuneec
Hello I update first ST16 to ST16_V3.1.22 and that was successfull. But now it doesn't connect to typhoon h any more. How to solve this? Is there some wifi setting I have to check that gets erased during upgrade?
Ever since i updated my Yuneec H, it cannot connect to gimbal. It's able to connect to the aircraft but it cannot connect to the camera. I have waited 5-10 minutes and it still is not able to connect. I also tried to unbind and bind but still did not work. Please help.
I seem to be having the same issues as a few others. I'm trying to update my gimbal to match the current V1.22, I currently have V1.21. The autopilot and camera seem to have the right versions. I've downloaded the software from www.yuneec.com/download/firmware/TyphoonH_Ver2.10_A.bin , tried to extract as it's a zip file and tried to add without extracting onto the SD card. Each time I connect it to the Typhoon H I get the error "No firmware in SDcard, update failed!". I've also attempted two differed MicroSD cards to cover my bases. Please advise.Zip file reads: TyphoonH_Ver2.10_A.zipExtracted file reads: files.zzz
Sorry but I don`t have Facebook. Could you just talk to me on here. I would like to review one of your drone products on my channel as my first video as I have been amazed on how good your are. Please reply and thankyou
