I've watched a bunch of the vids on using this system. I've ordered and received mine. There are vids which addrees how to avoid potential problems.. One of the tips is to set your triangles from the mid point of your top and work outward from there, not from the outside inward. Apparently it is in the written instructions to improve accuracy. Don't ask me why, but apparently it is a thing that some machinists have also confirmed makes things more accurate.
an incredible tool that really works very well, Peter Parfitt its creator really is a genius, admiration for him and also for you sedge, great work! thanks
I wasn't sure about it when I first bought it. However after my first couple of benches it's amazing. Its allowed me to help out friends and also try out other ideas like extension wings etc. Even though its expensive you'll make your money back after two benches - HIGHLY RECOMMENDED!
Great demonstration, Brian! I made my MFT-style workbench/assembly table four years ago using the MK2 version and it was much easier than I thought it would be. I did see some blowout on the bottom of the Valchromat because I didn't use a backer board...lesson learned. This means I can't flip the worktop over when the first side is too abused, but after four years of nearly daily use, it is still in great condition.
I have just started in woodworking as a retired metal worker. I bought this system a little while ago and love it. I also want to thank you, after watching your content I now own a Domino 500, TS55, CT36 and an OF1400, I also have CSC SYS 50 on order that I hope will be delivered this week. To say I am very impressed with the FESTOOL engineering and build quality would be a massive understatement.
I picked up the PGS on Thursday. I can’t wait to use it! Looking forward to seeing your future videos on this. I bet there are so many great jigs that can be made. You did such a great way of explaining it.
Hi Sedge, I have been using the Parf Guide System since the 1st version. I used it so much I upgraded to the Mark 2 version. The key is taking the time to register each pin/drill guide and you can end up with very close to CNC accuracy. Your walk through is right on the money. Johnny O...
Hello Sedge, I also bought the system because the Mft were too expensive for me. I'm very happy with it. You also explained very well how to apply it. 👍 Thank you.
Thank you for sharing cause just got the UJK Parf Guide System Mark 2 to make my mft work top. This video was a big help on understanding the system. Thank you again.
Cool Video Sedge. I also bored 20mm holes on my drill press table. Their only 64mm apart but they work great for using all my Festool style clamping accessories on my drill press table.
This is a great system, I have made many tops with this. When I do the 3mm holes I put blue tape over the offset holes so I don’t accidentally drill them😅
@@sedgetool me too, had it for a few years, I’ve made some sectional benches nearly 12’ long, all the holes lined up perfectly. Love your work and enthusiasm Sedge.
Hi Sedge, used the system extensively a point to note check the cutter sometimes when breaking through the bottom of the hole it leaves a disc on the cutter as it’s extracted and makes the next cut a struggle Steve
The only issue with making a thicker top is that you won't be able to fit clamps through the dog holes, and certain accessories that clamp to the MFT tops are only designed for 18mm tops. The clamp issue can be mitigated by adding a big chamfer on the underside, but it's best to stick to an 18mm top.
I use the Festool Clamps and anything over 3/4 will not allow them to work.... .... I used this system for my 1 1/4" beech workbench and it works great for all my TSO / UJK dogs !!!
You will get tearout with any forstner bit if you're using plywood, the solution is drill all your 3mm pilot holes, flip the top over and score the ply freehand with the forstner bit. Then flip it again and proceed as normal.
One huge tip: if you're using the Parf guide with plywood, the pins may be very difficult to insert and remove. If that is the case, dip them in paste wax or something similar every so often, this will save you from getting nasty blisters on your fingers. Ask me how I know :^)
@billF2380 It actually makes no difference whether the Parf System uses metric or imperial. The important point is to create a grid of holes at right angles. You will need 20 mm dogs, but you can use any measuring system in your work.
Using the Parf System, you can make multiple tops. Also, in a previous video, Sedge demonstrated using the system to add holes to his woodworking table, showing the adaptability of the system.
I wanted to have the 200 holes in my 1x2 meter Valchromat top done at a CNC shop, but none would guarantee the accuracy of the holes or the grid over the length of the top. If I insisted, the cost would be about €300 if I provided the Valchromat. The cost of the Parf Guide MK2 was about €200 and I can make as many tops as I want in my shop.
@@Mike--K How lucky we are in India , cnc person gave me almost 6 x 3 feet sheet done in almost your 8 dollor. But yes hole were not exactly 3/4" but grid was exact.
the holes in the parf sticks are guaranteed to be perfectly aligned but the edges are not. You should not depend on the edges of the parf sticks to be straight or parallel or perfectly aligned with the holes.
