Тёмный

Valdosta gazebo fan - Allan + Roth / Harbor Breeze and install 

BigGoofyRunner & Family
Подписаться 11 тыс.
Просмотров 6 тыс.
50% 1

Our new gazebo needed help with air flow - the heavy duty mosquito netting really blocks breezes. So we found this plug-in fan from Allen + Roth (now called Harbor Breeze) at Rona here in Canada (also available at Lowes - Lowes is now Rona+) that can be hung right from a hook in our gazebo roof and plugged in to power - no hard wiring required.
The fan is very stable even running on high - which is a nice surprise.
The only dislike was the stick down cable tie mounts would not stay stuck to the gazebo roof - we used some 3M command strips instead that worked much better.
0:00 Intro
0:28 fan description / box
2:40 unboxing and assembly
9:45 fan install
11:55 fan test
13:25 how fan works for air flow in gazebo
14:23 realized I missed a part in assembly
14:46 all fixed
15:20 install cleaned up
15:42 Outro and final thoughts

Опубликовано:

 

4 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 7   
@jvideosearch111
@jvideosearch111 День назад
What panel do you have hanging up? Can you do an update on the electrical
@Cerabris
@Cerabris 7 месяцев назад
It’s no longer under the Allen + Roth brand, it’s now a Harbor Breeze
@sentient_pancake
@sentient_pancake 11 месяцев назад
hey this is random but i’m trying to pull the cage off one of these (where i work) in order to clean the cage/blades. i can’t figure out how it comes apart though. i’ve tried googling but can’t find anything about it. i’ve removed the screws around the outside but i’m afraid to yank on the cage or force the knob… any advice?
@BGRFamily
@BGRFamily 11 месяцев назад
Hey there - I had to go take a look just to see, and it doesn't look super straight forward and there are no instructions in the manual either. Best I can see is that you remove the screw holding the metal band that wraps around the two cage parts - I haven't tried it yet, but it looks like this would then allow you to pull down on the lower part of the cage to separate the upper part of the cage from the lower part and band. But I do also see that there are spaced clips that are screwed into the band every few inches, if those clips are too tight, you might not be able to pull the two sides apart easily. That would then likely require loosening the screws for each those clips. But, that is just and educated guess, unfortunately. Hope it helps...and good luck!
@jackcrotty7461
@jackcrotty7461 10 месяцев назад
I have same fan you have. I did unscrewed the band and unscrewed 8 screws off around the cages... still I unable to open the bottom cage at all because the dial low/med/high is probably glued on. Crazy!!!
@tavorismark2082
@tavorismark2082 Месяц назад
He mentions around 5:30 -5:31 in video how to clean!
@jamesbourke3844
@jamesbourke3844 24 дня назад
The fan control knob pops off with a flathead screw driver and will go back on.
Далее
Best Hardware to Hang a Ceiling Fan
12:29
Просмотров 63 тыс.
ТЫ С ДРУГОМ В ДЕТСТВЕ😂#shorts
01:00
ELA NÃO ESPERAVA POR ISSO 🥶 ATTITUDE #shorts
00:20
Canopy Fan Review
6:13
Просмотров 12 тыс.
8 Best Outdoor Ceiling Fans
9:09
Просмотров 25 тыс.
Harbor Breeze 20" Valdosta Fan
10:05
Просмотров 17 тыс.
Outdoor Outlets on Deck or Pergola | Skip the Conduit!
8:08
Build a Gazebo Fast (Time Saving Hack)
32:27
Просмотров 533 тыс.
ТЫ С ДРУГОМ В ДЕТСТВЕ😂#shorts
01:00