VW Audi Steering Wheel Angle Sensor Basic Settings DIY by Edge Motors 

Finally, after almost a year of searching I found a guy who did actually explain how to take care of that shit, it's very annoying

You helped me and saved me a lot of time and hanging around with vsdc and their manuals. Thanks!

Thank you so much man! Took three tries but now it finally worked!

AWESOME, video, Thank you for sharing the knowledge, may you be blessed 😇

Thank you a lot... so I just cleaned my battery terminals real good and I got all these lights up... just did the steering left right and it’s gone👍👍👍

Thank you so much for the info!! Worked like a charm ❤

OMG thank you very much it worked like a charm

Thanks and Well done............Fantastic info and guidance.

I have the same problem with the radio, can i just disconnect the radio or do i have to put in the original to calibrate the steering wheel sensor?

1000 stars, thanks alot mate, sorted the same problem.

Thank you worked like a charm with the autel ultra scanner

Thanks for this mate! saved me a load of time hunting round in vcds and trying to find the security code.

After doing this my steering wheel got very harder i did in only ignition on please help me what should i do now !!

Thank you very much, clear video fixed all the issues !!!

Thanks..........when you perform the left and right end stop...........do you need to be in a particular section of the the VCDS computer software setup ?

Or engine running, voltage re-applied - steering full lock left than full lock right then centre to manually set adaptation.

You are a genius:-)

Thank you so much. Very useful!👍

Thanks for your help, brilliant!! bloody nightmare but sorted now thanks to you.

Brilliant video A++++

Do you have to register the VIN ( use one of your vehicle registrations) to make the changes ? Thank you

It worked! Thanks a lot

I recently replaced my ABS module/pump and im getting 4 fault codes. Three of which are pretty common and need to do basic settings in. The only code that has me puzzled is a "Rotation rate sensor" electrical error in circuit which is the G202 to my understanding. Will this present code not allow me to do long coding on the new module and do basic settings/adapations?

hey, i retrofit my skoda with steering wheel with comands (from an none one) and now i cant cancel errors like yours, not on vcds, not with mecanical spining formula.... should i instal my old original radio and try again

Hello friend, I have a polo 9n3 1.2 12v, it happens that when I'm driving at least once a week an abs, steering, airbag warning appears... I turn off the car and everything returns to normal. I detected error P0600. I've seen the fuses, new battery, alternator charging 100%, I don't understand why🙄

Hello, why do you turn on the light of the traction together with that of the electric direction?

Excelente resolví con tu video

Great video. Can I ask you a question?? What if I only have the traction control light on?? I don’t have the steering wheel yellow light on. I have a 2007 Audi a3

What if the angle doesn't change when I turn the wheel? I know the rack has been replaced by a backyard mechanic. Could the wiring to the rack be the problem?

Hi Sir, I have audi q7 2017 and I had an accident and replaced all front suspension system along with sub-frame. Anyway finally I got red color signal in my dashboard says steering fault please stop vehicle. But my steering wheel is working fine with normal movement . Please help me as I went to local workshop and they told me I have to replace steering gearbox which cost around 4000$$😭😭

Thanks for this video i've done them before but at the end what you said about the incorrect module installed in the car so what you did is change the soft Coding of the radio ? I Saw you other vidéo first this is what i meant doing the basic setting of the angle sensor but never had to what you did in the other video. Thanks .

in a volkswagen passat 3.2 v6 I have the yellow light of the address on, this code tells me the scanner 01309 control unit signal defective, can you guide me please.

Life Saver

Hi please I need your help I installed a slip ring and Cruise control stacks in my Tiguan. I made the mistake and installed a slip ring with steering angle sensor while my module does not have steering sensor module as per the information on ROSS TECH site. So I got the errors anyway I removed the modification straight forward and reinstalled original slip ring and stacks. But now I am plagued by this steering wheel sensor error. I tried everything but the error says no communication with 60 like it can’t find steering wheel sensor of course it’s not there. So how do I tell this car stop looking for it. Please help Many thanks

I have audi a3 2.0 tdi 2005 stiff steering but no steering or traction control light is on please any idea what it could be?

Can you do video for MKV? Your explanation really good. Thanks.

Hi. I need to replace my steering angle Sensor. Do I do this after fitting the new one

Can this be done with vcds lite? I have same problem as video with 03 bora.

Works for me thanks settings convert to obdeleven pro ..

I drive a POLO 6R GTI 1.4 where to connect a cable in a car? I also have the same problem (Steering wheel not straight)

спасибо!

Hello Would you be able to tell me how to do this at Vcds version 15.7 thanks in advance

good night friend..you know how to solve defect code u1113 a4 tfsi 2010

Any help with a yellow steering wheel light, fault code is against the steering torque sensors... Do I go with the same approach? Basically happened when a local garage changed my CV boot!

Great video! Hey I have a 2003 audi a4 b6 3.0. I replaced my 5.7 abs module for a new one. I followed the ross-tech 5.7 install and coded everything fine, it accepts the code. However it wont accept the calibration for the angle sensor. I have no live reading of the sensor in VCDS (it's stuck on 2.5deg). So I'm guessing it's not accepting the basic settings because the wheels aren't straight enough for the sensor? Although if I put the old abs module back in, all the coding is accepted and the angle sensor calibrates fine. Both the ABS modules have the exact same numbers. Any idea what I could do? Thanks!

How to polo right dor red light sensor off

for a3 8v wher's the procedure?

here i am trying to find a way of getting wider steering angle for the passat but no vids lol

do you have any idea how to set steering end stop limit on Mk7 GTI?

tried this on my 2010 polo but I still have eps light and tyre pressure light on. no basic settings for steering angle adaption

what if i dont hsve vag com?

es portugues pa'

i dont have security access

how can i implement with obdeleven?