VW Tiguan Front Spring replacement and shock absorber removal. How to replace front coil spring

Подписаться 16 тыс.

Просмотров 36 тыс.

50% 1

Hello guys!
#AlexTheGrumpyOne here with another video for you :)
Here is a video on VW Tiguan Front Spring replacement and shock absorber removal. This will be the same on quite few vehicles in VAG group. I had the same set up on my Audi Q3 in the past as well.
So, here we got a video on how to do the job and what tools you will need for it.
I hope you find it helpful and that you will be very careful while doing it!!!
Tools that I have used for this job:
Milwaukee 3/8 gun: amzn.to/2MpAqH2
Wire brush: amzn.to/3kpA7bF
Wire brush kit for drill: amzn.to/3kky097
Maintenance spray or WD40: amzn.to/2ZQDK0I
Spanners: www.tools2udirectsw.com/us-pr...
Vag group impact spline kit: www.tools2udirectsw.com/us-pr...
Rubber hammer: amzn.to/3uw7xdu
Chisel set: www.tools2udirectsw.com/us-pr...
Hub spreader tool: amzn.to/3pN807z
Hammer set: www.tools2udirectsw.com/us-pr...
Lower arm/ wishbone removal tool: amzn.to/3aQPKpF
Torx and Alan bit set: www.tools2udirectsw.com/us-pr...
Ring offset Spanners set: amzn.to/37KJ0HG
Water pump grips: www.tools2udirectsw.com/us-pr...
Wheel nut sockets: www.tools2udirectsw.com/blues...
Torque wench 1/2: www.tools2udirectsw.com/us-pr...
Torque wrench 3/8: www.tools2udirectsw.com/us-pr...
Torque settings:
Wheel nuts - 122NM;
Nut on the spline bolt M14 bolt 70NM + 90º;
Nut on top of the spring mount 60NM;
3 13mm top bolts 15NM + 90º;
Anti roll bar link nut 65NM;
Disclaimer:
This video only contains tips and recommendations that could be helpful when carrying out car repairs or replacing parts. AlexTheGrumpyOne is not liable for any harm, injury or property damage incurred while carrying out repairs or replacements, that are a result of incorrect use or misinterpretation of the provided information. This video is for informational purposes only and does not guarantee achievement of a specific result. The user is personally liable for incorrect use of repair equipment, tools or car parts, in particular, when this use poses the risk of injury. AlexTheGrumpyOne strongly recommends being careful and adhering to the safety rules when doing any repair or replacement. Keep in mind that using low quality auto parts does not guarantee the proper level of road safety.
If you like to get your hoodie or any other clothes with logo made for you, then I would like to recommend you an amazing Logo company that made my ones, which I am very happy with.
Here is a link to it #ppwork
www.ppwork.co.uk
They got plenty of different options and deals!
Team is very friendly and I am sure they will be happy to help you!
If you need anymore help, just let me know and I can even do it in few different languages : English, Portuguese, Spanish, Russian and Ukrainian.
Before you go don´t forget to Subscribe, like and share :)
Comment below to let me know where are you from and what you think about my video :)
Equipment used to film:
Canon 90D: amzn.to/2TuhQxb
Canon lens: amzn.to/3kwMEJJ
Samsung S10: amzn.to/2TqszIW
Tripod: amzn.to/2HzFPZo
Gimbal: amzn.to/3dXYhH0
Thank you!
Obrigado!
Спасибо!
Дякую!
Gracias!
Good Luck and Stay Safe!
Instagram: alexthegrumpyone
Facebook page: alexthegrumpy1/
Facebook group: groups/alexthegrumpyone

Авто/Мото

Опубликовано:

24 фев 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 82

@ehyme56 3 года назад

Awesome video with top quality production. I plan on swapping the Tiguan suspension onto my Sportwagen. This is very informative.

@AlexTheGrumpyOne 3 года назад

Thank you! I really appreciate your support :) The passenger side one I would say you have to remove the drive shaft out of the hub as it will make it a lot easier!

@danyo1972 Год назад

Good job. Nice video. Great not having to take the axle bolt off. This isn’t so hard to do with a two post lift, a professional spring compressor, the special tool for holding the arm down and a transmission jack. A bit more difficult without all those tools, whilst working outside on your driveway 😂. Replace any bolts that have an angle turn in the tightening settings, they are stretch bolts. If your shocks are old and or damaged now would be a good time to replace them. Likewise with the top mounts.

@AlexTheGrumpyOne Год назад

Thank you very much. Yeah without the lift is a pain, I've done that for long time. Best thing I've ever got haha

@carlosbrioso83 3 года назад

Great video and great description of the whole process. Thanks

@AlexTheGrumpyOne 3 года назад

You are welcome! I am glad that you find it helpful! Good Luck with your one!

@19NinetyUK 2 года назад

Brilliant video, made it look simple. Cheers

@AlexTheGrumpyOne 2 года назад

Thank you for your support :) I appreciate it

@sunilraj7692 2 года назад

Great video! Awesome instructions.

@AlexTheGrumpyOne 2 года назад

Thank you 😀 I'm glad that it is helpful

@markjones8437 3 года назад

Great video - thanks for uploading ! Very informative !

@AlexTheGrumpyOne 3 года назад

You are welcome :) I'm glad you found it helpful. Good luck with your one.

@jilljames4530 11 месяцев назад

Nice work Alex 👍🏻

@AlexTheGrumpyOne 11 месяцев назад

Thank you 😀

@BendelaGarza 10 месяцев назад

Wanted to thank you for all the help as the install was successful. One note to people in America getting the replacement strut assembly from AutoZone. The 3 bolts on the top mount are SAE 1/2", not 13 mm like the original. That threw me for a loop for a minute with the torque wrench. America always has to be different smh

@AlexTheGrumpyOne 10 месяцев назад

Awesome 👌 thank you for the helpful info as well 😀

@MrZimmaframe 2 года назад

13:35 I didn't have the spreading tool so i made one with an m10 bolt, i just ground down the thread and metal on two sides so it was more of an oval, then just used a ratchet and socket to turn it to spread the rub and it worked really well to my surprise lol. Hey Alex been watching some of your older videos recently and they are really good man. Keep up the good content man. 👍😄

@AlexTheGrumpyOne 2 года назад

Hello bud! Thank you 😀 Yep thats great! Well done for making the tool up bud! I use to use chisel before. That works as a treat as well.

@MrZimmaframe 2 года назад

@@AlexTheGrumpyOne Oops fixed my spelling mistake. Yeah chisels work great too.

@user-eq7cc1yt6z 2 года назад

nice explaining. helps me

@AlexTheGrumpyOne 2 года назад

Thank you I appreciate your support 😀

@SpikesMavic 8 месяцев назад

Excellent vid, thank you

@AlexTheGrumpyOne 8 месяцев назад

Thank you 😀

@TheParachaz 3 года назад

I don’t have a car lift or long bar for pulling the hub down, so I used a small bottle jack for separating the bottom of the shock from the hub. The socket separator for the split at the back is a real boon, cheap to buy on eBay. I didn’t need to remove the brake tube carrier, but I did cut the drop link as I wanted to replace that too, the splined holes kept rotating, cut them off with a angle grinder! The stretch bolts are remove and replace! , cheap as chips to buy.

@AlexTheGrumpyOne 3 года назад

Well done! That's great news. I use to do them in a similar way before I had a car lift :)

@MarkSegree 3 года назад

Still trying to wrap my head around where you put the jack but most importantly, what is the separation tool called or what was the search words that you used?

@TheParachaz 3 года назад

@@MarkSegree suspension strut splitter tool, it’s a socket with an oval pry tool in the end, you place it at the back of the hub where the split is, then rotate it 90* to open the hub out. It’s a small amount but enough, just make sure you wet the area well with wd40 or similar first. I placed the bottle jack tight against the bottom of the strut on the small shoulder of the hub surrounding the strut, then placing the top under the part where the spring bottom rests, gently does it and it pops out.

@AlexTheGrumpyOne 3 года назад

Thank you for your help. Thats a very good instruction there

@SpikesMavic 8 месяцев назад

Did You forget to shove the top bumber rubber into the top bearing housing !

@AlexTheGrumpyOne 8 месяцев назад

Hi there. No I haven't. Didn't I show it in the Video? Sorry

@dandyer8351 3 года назад

Good vid but you missed a important point about the top mounts. They are directional theres two arrows on them and they should bolt in with one arrow pointing to the front and the other to the back of the car.

@AlexTheGrumpyOne 3 года назад

Thank you. Yes that true. I did mentioned about marking the bolts at the top to make sure you fit it the right way back in due to that situation.

@Axabraxa 8 месяцев назад

Thanks allot for showing the possibility to remove the strut without removing driveshaft that needs thst special vw 12spline socket special tool that makes me dislike vw more and more compared to French and Japanese cars that also got less rust afak

@AlexTheGrumpyOne 8 месяцев назад

No worries at all. Yep trust me they are a pain

@michaelpaparelli6628 Год назад

How do you put the shock back into that shackle at the bottom?! 27:14 I’m stuck I can’t manipulate it man that’s the hardest part & up skipped over the whole process.

@hunk2493 2 месяца назад

Hi buddy. I have the same spring compressor but having trouble using it how do you line up the shockabsorber to be in center of the coil spring while pumping up so the top mount can go on correctly. I see you have used a shim is this nessary.

@AlexTheGrumpyOne 2 месяца назад

Hi there..yeah I have those issues. The quality isn't the best to be honest. Having grease on the sliding part helps as it gets stuck on the base when spring pushes to much to one side

@dainuri 2 года назад

Hi...@26.30, do we need to consider the arrow direction on top of the mounting in order to install this absorber?

@AlexTheGrumpyOne 2 года назад

Yes, it goes the same way as it came out 😀

@markjones8437 3 года назад

Alex - sorry to bother you but could you share where you got the spring compressor from ?

@AlexTheGrumpyOne 3 года назад

No problem at all. Sorry I forgot to put that in description as well. here is the link to it: amzn.to/3czb6XY

@BendelaGarza 11 месяцев назад

This is proving fairly difficult so far, but i just began this weekend. The sway bar link came off easily, but that bolt holding the strut is a rough one. The nut on the end came off with minimal struggle, and i slid it back on a bit per your suggestion for hammering the end. My main problem now is i don't have an impact driver with enough torque. How many foot pounds is your driver? The regular hand ratchet isn't going to do the trick. I've lubricated it a lot and did hammer a chisel between the knuckle

@BendelaGarza 11 месяцев назад

Just saw the video description. Milwaukee 3/8

@AlexTheGrumpyOne 11 месяцев назад

Yep that's the one. Brilliant tool by the way

@BendelaGarza 11 месяцев назад

@@AlexTheGrumpyOne I shelled out for the Milwaukee with 4 AH battery. Hopefully that'll be enough.

@BendelaGarza 11 месяцев назад

@@AlexTheGrumpyOne one more quick question, could you preemptively use the strut spreader bit before the bolt is out instead of the chisel?

@AlexTheGrumpyOne 11 месяцев назад

The bolt needs to be out to before you use that. U can get the bolt out by turning it first if its stuck

@plusultra440 11 месяцев назад

If only one spring was broken, would you have still replaced both front springs at same time?

@AlexTheGrumpyOne 11 месяцев назад

That's what manufacturers recommend. I can tell.u that a lot of people and garages just replace one

@SpiralMoss 2 года назад

Hi there I'm in Ireland, my mechanic is really busy and he's always been trustworthy and my front left spring is clunking. He said it needs to be replaced. It's Tuesday and he said hes up the walls he'll fix it Friday but I'm not around Friday. So he said Monday will be ok.... it's not totally gone or snapped in half. Just on the way out. Should it be ok until then

@AlexTheGrumpyOne 2 года назад

So it's just a bit on the end that snapped? If its still seating in the mount ok and not on the edge you should be ok. I would recommend avoiding driving though to be safe. I would also recommend doing top mount in the same time

@SpiralMoss 2 года назад

@@AlexTheGrumpyOne Yeah it's well seated in the mount and secure I rang the mechanic again he said it's slightly bent and causing the clunky noise. Just take it easy until then and no rough rural roads...it's not fully snapped yet Thanks for your speedy response much appreciated 💫👍

@brazeaujames 2 года назад

How many hours labor wise are we looking at to replace the front pair? VW is charging an extreme amount.

@AlexTheGrumpyOne 2 года назад

Hi there. Usually depends if things come undone and if the antiroll bar links come undone as well. I would say 1 hour and 30 min each side at max.

@brazeaujames 2 года назад

@@AlexTheGrumpyOne okay thanks they want to charge 1500$ in labor... Didn't know they included their lunch breaks 😂

@AlexTheGrumpyOne 2 года назад

Bloody hell! Haha that's expensive

@douglee7985 2 года назад

What year of vehicle are you working on?!?!

@AlexTheGrumpyOne 2 года назад

2009

@johnjoerice 2 года назад

It didn’t end well for my car. The drive shaft is easy to take off, my suspension wouldn’t go back in. Wish I had taken the drive shaft off first

@AlexTheGrumpyOne 2 года назад

Was it on the same side or the passenger side one?

@Samirkerbadj74 3 года назад

Hi Alex I'm new to your channel, I hope you can help me fixing a problem on my 2012 Skoda fabia 1.6tdi. The problem is, the engine was shaking very badly, so I took it to a garage which they said it's injector problem, we changed the injector but the engine still shaking, although the scanner has no fault registered after the fitting of the injector, the mechanic said maybe is the ECU!!!! But o doubt it!! What do you think is the problem!?

@AlexTheGrumpyOne 3 года назад

Hello and welcome :) I am sorry to hear that you experiencing problems with your car. I'll try and help as much as I can. First thing is... we're the new injectors brand new or refurbished? Did he code them and learned the values after fitting them?

@Samirkerbadj74 3 года назад

@@AlexTheGrumpyOne yes he did code them all again, but the shaking still here

@Samirkerbadj74 3 года назад

@@AlexTheGrumpyOne the injector is refurbished yes alex

@Samirkerbadj74 3 года назад

What's confusing is there's no fault shown on IIOBD at all !!!

@AlexTheGrumpyOne 3 года назад

If the injection isn't coded it will not show faults sometimes.

@SpikesMavic 8 месяцев назад

Hi. Is it a Mk1 or 2 Tig.

@AlexTheGrumpyOne 8 месяцев назад

That one is mk2 but it's the same as mk1

@SpikesMavic 8 месяцев назад

Nah its not, the anti roll bar goes underneath the drive shaft when pressing down to get strut out it the drive shaft touches the the bar. also it is a 6mm allen for the top if the strut on a mk1 not 7 has in the mk2