Whirlpool Dishwasher not spraying water and stop cleaning - How to fix it 

Yours was the only video I could find with this model of Whirlpool. This was exactly the same symptoms and the same clogged motor as my mother’s dishwasher. It was actually way more time consuming just getting the dishwasher out because of a short, hard to reach water hose and equally frustrating hard-wired power cable. But once I finally got it out your clear instructions on removing and cleaning the motor were spot on! Saved me hundreds of dollars! Thank you, Mr. Stukov!

Thank you so much for this video!!!! I was seconds away from purchasing a new dishwasher when I found this tutorial. The circulation pump was dirty. My dishwasher is working beautifully now!!!!

This 100% was our issue. Thank you Sir!!! Dishwasher would fill and drain but there was no spraying at all. Took the unit out(had to disconnect hardwired electrical but it was easy) removed the gunk from that piece and it works!!! Thanks!!🎉

excellent vid. took mine apart and checked this out, but it was clean as could be. kept searching YT and found one where the guy used a toilet plunger to clean the line from inside the cabinet. tried that and between ensuring the pump was clean and purging the line within the cabinet, works like a charm. Thanks! New sub.

Thanks for your video, my dishwasher wasn't spraying so I took it apart hoping that would be the fix. Except mine was not clogged. Perfectly clean. Pretty disappointed I was envisioning a costly repair. I pulled the magnet out of the pump and discovered that it had a huge split running the length of it. Quick jump to Amazon, 2 days later and 50 bucks poorer I had a new pump. It now works like new. You saved me at a minimum a service call.

Thank you so much, saved my dishwasher. Broken glass and lemonade seed in it! Now working as should again.

Thank you so much man, you saved me hundred(s) of dollars of reparation fees. There was a single strong fiber stuck in the pump motor 👍

Thank you, Comrade! Nice video. I wish you showed how to disconnect it first.

Thank you! Had a piece of plastic stuck in there worked perfectly after removing!

This video just saved me hundreds of dollars! Bless you sir

thanks for this. my motor was fairly clean, but had some glass causing the impeller to seize.

Thank you! Had a piece of plastic lodged in mine.

Thank you sooo much for posting this! This was part of the problem with our dishwasher that needed fixed. Keep up the good work!

Had some gunk and chunks of plastic in my propeller. Thanks for the video..

Much appreciated! I will be giving this a shot as a regular maintenance.

Fixed! Hair around the motor. Used a little hook tool to clear it out. Hooked back up and cycle started! Yay

You are the man. Perfect video, please carry on sir.

How did you get the washer arm apart?

Thanks for the video, my dishwasher is working like new!!!

Simple and excellent! Thank you!

100% Fixed our dishwasher.

Omg thank you so much!!! I was about to throw my dishwasher and this video saved us a good amount of money and time

Nice and to the point! thank you sir!

This video saved me so much money thank you 👍

Wow! Great video! Thank you

Rock star. Very resourceful. My turn.

Mine had the same problem..yet it was fairly clean..but there is a screen under the impellar Hydro turbine which requires cleaning with a tooth brush and dish soap..the area in which the fellow in this vid is pulling out debris is the impellar housing remove the 4 screws and you can gain access..simply unwind(unscrew) the impellar from the threaded shaft to expose the screen below..it's ridiculous how such a small part blockage can cause a complete shut down of the machine- my model is WDT750SAHZ0..note to remove the pump you must tip the pumps square side post out of it's rubber insulation slot at the bottom of the machine..turning it clock wise..I had a tough time turning it so used WD40 on the contact rim..also remove the interior wash screen first and also the pump power clip..the smaller other pump is for the machine draining only..push 3 of the mode buttons 3 times each consecutively a total of nine to enter the machine reset and cycle..the machine will cycle through for errors..and reset.

How did you open the propeller arms? They seem to be glued closed on mine (same model). And how did you close them after? They seem to be built to prevent people from opening and cleaning!

Thank you for you video

excellent, thank you

How do you "extract your dishwasher" so you can get to the motor ?

Now you know not to put dishes that have debris into the dishwasher 👍 Food waste goes into the trash not in dishwasher !!

Thanks man

thank you sir!

How did you have light in there? I tried to 'wash' my GoPro, but it's completely dark in there and nothing can be seen

Mine was clean as well but can't get it back on properly so it doesn't leak

I can't get get the pump disconnected. Why the hell was yours so easy? 😂

Bingo!

Very helpful. Thank you. You saved me money

Как ты засунул туда айфон?

Nothing was clogged looked clean inside did not help at all