THIS MAN IS FANTASTIC. MAKES COMPLICATED THINGS REALLY EASY. mY 12 YRS OLD HOTPOINT WASHER DRYER IS WORKING AGAIN, FOR JUST 30€. PLEASE DON´T STOP DOING VIDEOS!!! AND THANKYOU
That is great to hear Reagyn. May we recommend another couple of videos you may find useful?: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ifWK9df1qgg.html and ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-uKBy-9NEF5A.html
On our Duet, the F11 error was due to an intermittent 3 pin connector to the MCU. I re-positioned pins and sprayed off the terminals with Deoxit. Now it runs like new. Thank you very much for creating this video with emphasis on the harness connectors, you probably saved us $250 in repairs!
Hello, what does the F13 code indicate, even though a new lock was replaced and the number is still the same and the machine does not work, the door locks and does not work and the service light is on?
What does F1 mean? I know it has something to do with the lock cause mine is locked, and I can't get it open. It's not the control lock. And I have had it unplugged for at least 5 minutes.
Thanks Julian, if you have a problem remember we also have loads of 'diagnosis videos' for all most appliances like this: ru-vid.com/group/PLZopaZU-UQSHj1noiwEJ99JjXWcEcSAbZ
Well. I checked the connections of the water supply and cleaned them out. Then checked the dispenser compartment for clogs.Massaged the hose just in case a blockage was there. None. I didn't check the solenoids because I don't have a meter. Pressure is ok but still getting 3 beeps. The major is filling up to proper level of water. Water pressure sounds good. I cut down the hose on the back so water would drain properly. Still no good results....HAve anymore Ideals?
The information you have given suggests you may have a pressure switch problem. For information on this see another video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2pIVkAxWSXg.html
My son just moved into a beauriful town home on the water but so many things are not working properly such as his whiirl pool side by side washer and dryer. The washer works horrible. Everytime he attempts to wash a load of clothes an area code A-09 comes on. He cant open the door and the only way hes able to is if he puts it on the rinse and spin cycle. Which is time consuming and not only that the electic and water bill is going to kill him. Thats one of the issues here that the electric bill is so high tenants have actually moved out.
Hi Denise, error code A09 is the machine saying there is a water inlet problem, your son needs to check the water supply and make sure there is water getting to the machine.
I'm getting an E01/F03 on a new USA-made Whirlpool, which isn't listed here. I notice that many of the unanswered questions below pertain to US-made Whirlpool products. Is it possible that the error codes on EU or UK sold WP machines are different from those of their US counterparts? I know WP bought out Indeset/Hotpoint, so the design of the machine here may have little in common with mine. Thanks for the information anyway.
There can be different codes even for machines made for the same 'markets' but the codes quoted are the 'commonly used'. E01 can be a draining problem and F03 can be a pressure switch related error so if you are getting these it suggests the machine is 'expecting' the water to be completely drained but the pressure switch is 'reporting' water in the drum. The usual cause would be a partial or complete drain blockage so watch another video for more information: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-frEJhX9Sppw.html
Hello, I have a whirlpool sports 6th sense. It's washing fine but lately I have noticed that loads are going on for far too long. For example there will be 1 minute left on the screen then it goes back to 30mins rinsing over and over again. Eventually I will manually reset and do a rinse cycle to finish off. Please help!
Hi, I have a Whirpool HDW 1011WG, halfway through the program the window flashes H then F, then H then F continously. Then select pause reset button and time comes up 21 mins and pump runs continous and won't move on from there
I have a Duet steam model wfw8640bw1 about 3 years old. The power button no longer works and when I try to start a load the delayed start is displayed after holding start buttons for at least 30 seconds. I have to try several times for the cycle to begin. Suggestions?
Hi Ashneel, we do not have either error codes listed on a whirlpool washing machine, you will need to contact the manufacturer but please let us know how you get on.
Great video. I had f01 issue which got fixed by replacing the control panel, and it worked for 1 day and then start showing me error f31. any guidance?
Hi The Mimi' s, F31 means the machine has detected the motor control unit has overheated, check the connections from the motor to the central control unit and test the motor to determine if it has failed.
Hi The Mimi' s, F28 is a communication error between the boards, try this Unplug washer or disconnect power. Check wiring harness connections to the MCU, the motor, and Central Control Unit (CCU). - Check connections of the CCU board within the housing. - Make sure all grounding switches are engaged. Check that the serial harness at the MCU is not mounted upside down. The wires should be to the left when facing the MCU connectors. Check the drive system for any worn or failed components the plug in the washer or reconnect power.
hi, thanks for your awesome video! I have a WFW9050XW03 but it doesn't have a LED display, how can I decipher the error code ?. it is stuck on Wash, beeping 3 times, and the LED on the WASH flashing 8 times and then once and then repeat. thanks a lot!
Hi Michel, the code is generated because the fill sequence is taking too long, check the pressure switch hose that runs from the tub to the pressure switch as this can cause the problem.
I have a front loader washer whirlpool energy saver. When I press the start button, door locks but then that’s it. No water and no spinning. Timer works but machine is stuck
Hi I have a whirlpool duet front load washer the code disappeared however the red door locked but is lit up. And it sounds like it’s draining but not unlocking even after minutes please help what should I do?
Hi J M, let's start by getting the door open this video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-J7vzWGMvfOM.html&t shows you how to release the door then check the door lock and the electrical connections between the lock and the board.
Hi Ayush, you did not give a model so I can only give general advice. DE usually indicates a door error, check the door closes correctly and if it reoccurs suspect the door lock. Error FE is usually a filling error. Check the machine fills to the correct level in the right time (about 1 Minute), check the water supply tap is turned fully on.
Hi autocuntversions, it means the machine has detected an error with the dryer sensor, we have an article to help on this www.espares.co.uk/advice/symptom/hoover-washer-dryer-error-code-e11
Ok, I've watched this video twice now because the first time I didn't hear my problem.......or the second time. I have a Whirlpool Duet washer and am getting a F13 error. Please advise.
Hi Lisa, although we have tried to make this a comprehensive list manufacturers will occasionally add another code. We believe this code is related to a motorised dispenser. The detergent dispenser has several compartments to allow pre-wash wash and conditioner to be loaded at the correct time. To do this it will 'divert' the filling water to the correct compartment. If the motor is jammed or if the control board is not receiving the feedback it will show this error. Check nothing is jamming the motor or flap.
Hi, we recommend checking the drain hose for kinks, check the condition of the drain pump and the electrical connections and check for any blockages inside the drain pump filter,.
Hello there eSpares! I too get an F23 faulty code on my top load Whirpool AWE 7516. What should i check? The pressure switch,the heater or the heater sensor? Thank you !
We believe this could be due to a couple of reasons. If the error occurs when filling with water it may be a blocked or failed pressure switch so see this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2pIVkAxWSXg.html
eSpares my problem is that i fill the washer with clothes, pick the program and start it. When i start it, there is NO water coming in, the motor goes twice for a couple of seconds and puff.. the f23 comes on.
All modules and PCB's can fail. Before suspecting this just confirm the machine is filling and starting a wash cycle?. Also try a spin cycle. If F08 appears immediately before the cycle starts suspect the sensor or the board.
My Whirlpool front loading machine, Model GHW9150PW4, starts to wash as usual but clicks off after a few seconds and locks the door, with Error Code F11. The manual and you did not mention Error Code F11. What is going on with my machine?
Hi Kathy, F11 is a communication error between the control board and the motor board, try checking the connections to both boards are making direct contact.
Hi Emmanuel, This will depend on the machine and as you have not given a model number I will try and give information that may help. Generally if the machine can work it will show the following (50/60hz) on the 'rating plate' where the model, serial number and voltage information is listed. If the machine uses a 'mains voltage pump' it is likely to be upset by supplying the wrong mains supply.
Hi Beatriz Chen Zhou, it is in the video F18 means the machine has detected an internal data error, try unplugging the machine for at least 3 minutes, reconnect and wait 30 seconds before trying again but if it happens again suspect the PCB.
Hi Richard, use a flat blade screwdriver to lift the retaining band off the door seal then you can pull the seal away from the cabinet, there should be screws at the bottom of the panel holding it on and just lift it up to release and take off.
@@eSpares the rubber is stuck on the fron panel. That comes loose. There's a screw on the machine part but I'm afraid that when i take that of i never going to put it back anymore. The rubber is to tight.
Hi Richard, if this is the first time the seal has come off the front panel they can be very tight to remove but they are designed to come off, try putting your fingers on the inside of the seal where it joins the front panel and push down and it should move the seal watch this video to help with the technique ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-NkdwIWGrOXo.html&t
This is a 'water supply error' where the machine does not think it has filled enough in the allowed time. For more information see our video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-VS48G_cwCXo.html
Hi I'm getting a code Lf. I've had someone come to check it bit that didn't do Me any good just lost money. I would rather learn how to fix it myself. ..
eSpares how would I know if the water is filling correctly? These machines don't really put out much water, so I really don't know what would be a good amount. I had someone come out, but that was just a waste he's telling me other things that's the opposite of my problem. .. is this something I can fix on my own or would I have to purchase another washer. my machine starts a whole new washing cycle on its own. Once a cycle is finished it comes up with the error code Lf and then it'll rewash the same load if I don't power it off in time. I'm very concerned especially concerned about what my water bill will be like next month.😓
Hi Samuel, error code F33 means the machine has detected an issue with the drain pump circuit, check the filter and test the drain pump with a multimeter.
I have a whirlpool cabrio washer and when it first cuts on the the water runs for about 5 seconds or sometimes longer then it beeps and stops the displays “du”
Hi Shamaya, we believe the error code may be related to the lid locking mechanism as the module board cannot determine if the door lock is locked or unlocked.
I've done everything in the video f21 error is still there . Resetting this model mhn30prbwwo commercial type without coin or card dispenser ,is very hard to find out . I did what you said to unplug the washer for 2 minutes and put it back again .i made several times . No reset is happening washer is not running . What should i check next Ccu or mcu ? Is there any handheld device to reset this .thank you !
Sorry we do not have information on commercial machines. The only suggestion we can offer is to watch one of our diagnosis videos that will give areas to check to help identify where the problem may be: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-QYPqpjLV7s4.html
Hi Zorba, the only thing we could find on the HE error codes for whirlpool relate to problems with the drain cycle, check the drain hose and filter before suspecting anything else.
Hi, I have a Whirlpool Supreme Care FSCR70414 and when power on it displays a code "dEn" (that "n" is like an "U" upside down, so maybe "dE17"). The only option that I have is to touch the start (play) button but in this case I have a random program shown and It happens nothing. At this moment the only functionality is the power of, for any other it just beeps. Do you have a hint what is happening?
When you say F9 error code check for leaks inside the machine I'm not sure how you would do that? I'm getting the F9 E1 error code and the system is not draining. I took it apart and there are no clogs or plugs at all
Hi Pablo, error code F33can suggest to multiple issues related to it, check the water supply first then the pressure switch for holes in the hose and the flow meter is functioning. test the pump with a multimeter and if all that is ok then it is likely to be control unit, good luck.
F3E1 error can be a blocked pressure switch hose stopping the machine identifying the water level in the drum. For more information see our video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2pIVkAxWSXg.html
Hi Eclipse Hydro, on some models whirlpool use 2 error codes which reads F5 E2 which refers to the machine has detected an error with the door not locking correctly so check the door is closing properly, make sure the connections to the lock are OK before suspecting the door lock.
Hi Chris, without a model number we can only give general advice. It is usually easier to lower the machine on its side and access from beneath as shown in some of our other drain pump videos.
I have a whirlpool Dual Tumble Fresh 4.0 and normal load goes through to last rinse cycle then shuts down and three beeps continuosly. Put it on Rinse Spin Cycle and the beeps came up during a fill cycle. Machine is level front sensor at kick/front panel is pressed. Don't know what to do from here. Please help.
This sounds like a filling or pressure switch problem, check the water flow is fast enough (turn tap fully on) and see the following videos: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-VS48G_cwCXo.html and ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2pIVkAxWSXg.html
We understand this is an overflow error indicating the water has filled too high in the drum. Reset the machine and watch a cycle to confirm the water is filling to the correct level.
The door seems to open and close fine. The end light is now permanently staying on and won't let me select a programme. Is there anyway of resetting the system please?
When the power is turned back on the system should reset. Check the motor brushes are not worn out and see our other videos: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-D5Aw7CBEGPI.html and ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-QYPqpjLV7s4.html
Hi CAZNTUBE, if your display is blank you need to check you have power so unplug the machine and plug something else in the socket to see if it works, test the fuse and use a multimeter to check from the plug to the board.
tnx, I had contact with a repair-store and they told me its the input electric board or something that's out of order' costs derectly 150 a 200'euro need to repair this...
If there is no display screen on the machine? Hi .. I have Kenmore He2 with no display screen to check the error code. What it does is ... When I start the machine nothing happens and it unlocks and then it locks back in after few seconds .. Then the water fills into the drum to an appropriate level and then the drum spins once and stops for a minute or 2 then all lights starts flashing after few minutes it drains the water and unlocks the door. I cleaned the drainage filter and also could hear a little squeeking noise when I rotate the drum by hand although the drum is rotating freely. My Machine vibrates like hell when on high spin. Kindly share your expertise.
Hello! I have an whirlpool washing machine AWE6317 and work only the motor! I habe doing the reset ine the first the machine takes the water when goes to the second the motor works very fast 2 times and the washing machine stops and 3 light are on! The service light and anothers 2 in program! What problem has?
So I tested the element and had no reading on the meter. So I decided to buy a new element and replaced it today ...the washer is heating up again and it works however I still get F08 as an error code even tho it heats up the water. Do you have any idea why? Please don't tell me it's the thermostat that will take another 4 days for delivery and it's more expensive then the bloody element 🤦🏻♂️
Hi Arkuda, try this we found 1. turn off the washing machine and unplug 2. press the start/pause button for at least 5 seconds 3. plug the washer back in and hopefully, it has reset, if not it could be a malfunction in the board.
So I took it apart again checked for continuity and it all seemed perfect. Managed to get into service mode and then it said F13 🤦🏻♂️as if I don't have enough problems lol. However F08 was gone from the service mode ... Test was successful door did look and unlock without a problem tho ... So decided to do an empty 15 min cicle and what do I see at the end of it ... F08 flashing with the service light 🤦🏻♂️ I am so frustrated
I have a F06 Error and it's not a motor brushes ( they are practically new! ). I've hear in your video @ 4:23 that there is a "Tacho Coil" that might be damaged? Should I check electric resistance of a coil? Thanks in advance.
F06 error is no feedback from the Tacho coil. When this normally occurs the drum would start spinning very fast as the motor is powered then slow and stop as no feedback was received. If the drum does not spin that is the reason why no feedback (F06) is displayed and that would be a drive problem.
eSpares funny thing is that the motor won't start at all?! After taking water the machine just stalls and F06 error pops up. That's why I'm worried that it could be MCU or even CCU which is in my opinion not worth fixing.
Run a short cycle on a hot wash and check if the water is showing signs of heating. if it is suspect the temperature sensor if it is not check the heating element.
Hi Shabeer, we do not recognize the error code E0003, can you give us some more details of the fault and model and look at this video for help ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-PvJlqOjG6Uc.html
Many machines bleep three times to either indicate a problem or that the cycle has finished. If you do not have an error code check what works by following this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-QYPqpjLV7s4.html this will help show what is going wrong.
hi, I'm getting a 5d error code, I cleaned drain out an found some debris. ran the machine in quick cycle an still 5d error code at the end of cycle, I repeated 2 more times same result, I then proceded to run the clean cycle with bleach and still 5d error code at end of cycle. I have the model WFW-8410. in your opinion is it the Pump failing or maybe a sock clogged in hose behind pump??
Error SD is usually indicating suds or excess foaming in the drum. This is usually caused by to much detergent so if it occurs run another rinse cycle and try reducing the detergent. If you suspect a drain problem watch our diagnosis video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-frEJhX9Sppw.html
Hi, I have a whirlpool awz 512/s e and the start button just keeps flashing on it and then it goes onto start delay but it won't enter into any wash programmes. Any ideas what the error might be please?
