WILL MY AUCTION CHAINSAWS START?? 

Looks like there's going to be some fun to be had with these saws, looking fwd to seeing the pistons. Thanks

I'm really looking forward to these saws. I know almost nothing about the modern stuff. The idea of not needing a screwdriver is interesting.

You definitely made out like a bandit for sure! From what I have seen with the 261 you could have a lot of fun with it. Been trying to get one myself, I still can't believe a guy ran a 36 inch bar

I can't believe how 2 out of 3 of those saws started the way they did!

I was anxious awaiting this video, and you never disappoint. Waiting to see if the saws will start is like being at a magic show and waiting for the rabbit to pop out of the hat!👍

Still looking like a good deal, excited to see what's revealed in the exhaust ports!

Typical Stihl... when they don't want to run. I love Stihl saws. My 036 Pro I finally got running few weeks ago. What a saw. But those two months I tore it down 4 times, chasing air leaks. I finally flattened the case down, had high spots where the cylinder sat. While I was there, did a gasket delete. It starts, runs, idles and pulls a 25" bar. Big saws are fun.

Went to stihl training one time when I worked at a dealer. They had a pallet full of them they bought back from customers.

Best ending EVER! dude you cad me crying laughing at the "I just inhaled a mosquito, later" with that look on your face LMAO!!!!!

Nice line up busy I hope u are well.

Looks like you did pretty good! Cheap saws will surprise you!

Battle of the 50s!! Can’t wait for it. Chewed on a skeeter just a few minutes ago and decided to come in and call it a night…..

Gotta pipe that 550!! I piped mine an it was a rippaa, buzzed straight through hardwoods 👌🤙🤙🤙

Scoop, Scoop and poop... oh well two of three ain't bad... TC Mahalo Tinman 🤙🤙🤙

Man that 550 is awesome for 30$ bucks I’m looking forward to that rebuild I’ve been wanting to see more auto tune stuff I just got a 562 a few months ago

The 261's muffler is the culprit for failure because it causes to much heat. Stilh was trying to create a catalytic converter with the muffler clear it out and they will run amazing

You'll need to take you Husqvarna autotune into the dealer if you need to buy a new carburetor to load/flash the firmware :^(

Feeling ya on the mosquitoes. I'm fighting flies watching this down in Tennessee

I’m exited you have a saw on your bench that I actually own! The 261 lol. Inhaled a mosquito 😮😅🥴

Tinman I just bought a MS 261 and it has the adjustable carb on it , and has a issue with the clutch drum wobble like your the crank is worn on the spot where the bearing rides so it needs a new crank , but it'll be a little hot rod when I'm done with it 😎

How are you doing tinman? I really want to see what you do to the ms261 that you recently bought. If possible, build that one soon

I did a top end on a 441 a while back. Pain to work on and heavy but pretty grunty when running.

With the husky 562xp would have to get a software update every so often for it to work properly 😁 my friend has one and it works perfectly fine after the update

Not sure what “gen” m tronic is on the 261 if it is gen2 u start it in triangle position let it run for 30 seconds it picks a tune then make 5 cuts and it picks the best tune from the 5 cuts and it’s good to go👌 bigger about the 441 the 550 looks and sounds good

$30 and She Runs Eh!!! Looking forward to seeing work on these!

You have got some good deals. I have a MKII 550 that's ported and its a screamer port yours it would make a good video.

Stihl ms261c start it. Idle 30 seconds on full start. ( dont open throttle it) then after 30 seconds hold trigger on full rpm it will run for upto 30 seconds running rough then it will open up and scream (keep throttle on full still) keep it screaming then it will go back to running rough. Turn saw off and restart the saw will be reset.

Two out of three are still very good for auction purchases saws. To be continued 😂

Great video buddy !!! 🇦🇺✊🏻

nothing like the anticipation of pulling the muffler off a newly acquired used saw

Great video buddy 😊.

Awesome video

I bet that Stihl 261 kept throwing chains because the clutch bearing is shot. I believe you said gov. auction saws which would be an operator deeming it dangerous and a mechanic saying cheaper to get a new one lol. All speculation just for giggles

Ms441 ( if a m tronic) start it on full start leave on that for 90 seconds turn it off restart and find a log and do 5 consistant cuts then turn it off and restart the saw will be reset.

Tinman got to have sugar in your pockets for a STIHL to run buddy 😮.

I love my 441 its got great power

Every 441 I've done I swear it will be the last... over engineering at its finest 😂

good stuff

Looking forward to seeing how bad a 441 actually is.

Running a saw on a 42 degree day in Australia would probably get you hung drawn and quartered.

I'll give $35 for the 550...No questions asked!😁

What would be better for a stihl 044 a meteor or hyway piston and cylinder

Go juice!

mosquitoes are 70% pure protein ..... i'm pretty sure you don't want to know what the other 30% is.... Later! 🤣

What stihl dealer in mb do you find has the best parts prices?

Really looking forward to the 441. You dont see too many of those

I'd say you scored buddy

M tronic, resets simular to the husky auto tune

Ever had a rotary Dolmar

How's the Tinman and family

30 bucks lol all day

I run a 24" 3/8 bar full chisel skip tooth on my 550 mark 1 and i love that little saw. For what it is strong runner for a 50cc saw.

I have found that if you ask ten people about saws and you will get ten different answers from people and probably be more confused 😮‍💨😩

The MS 441 is a Great saw when it runs , but my honest opinion it's a piece of 💩 wut a nightmare to work on i bought one when they first came out and had nothing but issues

Im a stihl tech. Never have i like ms441s they where tempremental.