Тёмный

Wisconsin AENL-D 9.2 hp Engine Rebuild and Cold Start 

BRUCEFORCE82
Подписаться 99
Просмотров 29 тыс.
50% 1

Wisconsin AENL-D 9.2 hp Engine 1960's, rebuilt with a break in period completed. People have been asking about the muffler I used and wanted to hear it running. Works great, IH-1 from Tractor Supply. Complete rebuild including new Std bore Piston. Rebuilt Carb & Magneto. New inspection plate and paint. I used very little gas, maybe a pint in the tank, I should have added more as you see it made it harder to start with a gravity feed fuel setup. The temp outside was mid 30's, the engine was stored in the garage at 50 so I felt safe not switching to a winter oil. I set the govenor to 2,800-2,900 and checked with a Tachometer. Zennith Carb and Fairbanks Morse Magneto.

Опубликовано:

 

6 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 65   
@aaron71
@aaron71 Год назад
Love hearing some vintage AENL!
@FormulaBoat
@FormulaBoat 2 года назад
Had one on a home built log splitter that was given to me. Total B to get started. Ran OK once running, but it was more of a piece of exercise equipment than anything else. I don't miss it at all. You did a nice job on yours, can tell you like it. Very cool.
@SwishrNet
@SwishrNet Год назад
I bought one from a guy that had there's on a log splitter! Maybe it was yours?
@markjurkovich7814
@markjurkovich7814 10 месяцев назад
I really like these engines. I have one on an asphalt roller. Runs gret. Great job on yours. 👍
@WildfoxFabrication
@WildfoxFabrication 4 года назад
I am an all-briggs guy,, but I gotta admit I like this engine.
@kd5byb
@kd5byb 10 лет назад
Very nice job - sounds great - very nice, smooth, even idle. I like the IH-1 muffer - going to have to pick one of those up next time I'm by Tractor Supply for my small collection of Wisconsin engines.
@chipwright6193
@chipwright6193 8 лет назад
That is a nice engine you've got there. I just bought one of those today with a Gorman Rupp pump mated to it. I'm looking forward to adding wheels and a handle to the base like yours has.
@rdmanone
@rdmanone 11 лет назад
Great job. Sounds great.
@paulsobus3803
@paulsobus3803 10 лет назад
Great job!
@JoshKilen
@JoshKilen 5 лет назад
very nice engine, and it is a real nice runner. I have a 1973 one, that came off a concrete mixer. mine has a short stubby shaft on it and my plan is to run a A.Y. McDonald clear water piston pump, yes i do have video on my channel. And I always wondered what is would look and sound like with a IH-1 muffler, I was originally going to buy a Wisconsin WD33 muffler but at $190 that is a bit much for me. Thanks for the video, and I hope you come over to my channel and see what I am up to.
@SwishrNet
@SwishrNet Год назад
I love your build. The muffler is a great addition. I have to say maybe your points were dirty or something. My Wisconsin would always start on a first pull. But if the magneto got damp it would always hinder the start-up.
@BRUCEFORCE82
@BRUCEFORCE82 Год назад
Found a fracture in carb casting and replaced it, runs 1 pull
@SwishrNet
@SwishrNet Год назад
@@BRUCEFORCE82 ahh! So that's what it was. I see welds on those things all the time. I guess its a common issue. I've had 2 of these and I always see welds on the down pipe.
@BRUCEFORCE82
@BRUCEFORCE82 10 лет назад
The oil plug will be located below magneto on the block facing up. The plug you refer to is for inspecting the magneto gear for timing
@timsmith3339
@timsmith3339 6 лет назад
Thanks, I think I adjusted but did not replace. Will try.
@MultiBuck78
@MultiBuck78 11 лет назад
I see old Tim sold you one of those red lettered name tags for your engine too. an aenld engine like this was my summer project too . fun to rebuild aren't they? but crazy expensive for parts, when you get that thing running you know you really have something to hang on to. great job on that engine, and good luck with it.
@BRUCEFORCE82
@BRUCEFORCE82 5 лет назад
Yes fun to rebuild, I recently scored a new ID tag when Wisconsin became Wisconsin LLC with the white and blue tag. Took the project further and tossed several NOS parts on it, from what I recall it was the head, carb, oil bath, correct fuel tank. Haven't run it since the parts change. I would have to watch this video over carefully, but I think this was prior to swapping for a standard key way crankshaft and new shroud. Engine looks about as new as it gets. The carburetor has the latest revision to prevent gas dripping if flooded, the mag I found is also the last revised part before they switched to flywheel ignition that ultimately ended production when supplier was no longer in business
@BRUCEFORCE82
@BRUCEFORCE82 11 лет назад
Thanks! Yeah I really enjoyed working on it. Looking forward to rebuild a few other Wisconsins once the funding permits.
@luisoresteroque5450
@luisoresteroque5450 4 года назад
Yo tube uno de esos es buenisimo
@robm.6825
@robm.6825 Год назад
Very nice job rebuilding that engine. Greetings from Parma, where in Cleveland do you live?
@haroldweis2741
@haroldweis2741 6 лет назад
Thanks, I'll check
@stefanivassvika
@stefanivassvika 10 лет назад
I need to correct some information, I mixed up the engine manufacturer with the magneto. I'm sorry for my mistake. Anyway, I've got hold of all the information on the engine
@stefanivassvika
@stefanivassvika 10 лет назад
Hello! I have got a Fairbanks engine and it looks just like your here and I wonder where I check the oil level, it's a plug next to the magneto, but I think it is too high to be the oil level. Grateful for answers, best regards Stefan. Nice motor by the way, very nice job.
@FastenDeezNutz
@FastenDeezNutz Год назад
I just bought a second one today. AENL-D 12hp with a gearbox and Magnito
@MarioLopez-qo7tk
@MarioLopez-qo7tk 3 месяца назад
where can a person buy AENL-D 12 hp around
@TheShadeTreeFixitMan
@TheShadeTreeFixitMan 9 лет назад
Wondering where you got your ID tags from? Nice engine for sure. I have an AENL that I am trying to get running.
@MarioLopez-qo7tk
@MarioLopez-qo7tk 17 дней назад
Bruceforce82 I am looking for the oil screen that goes in the oil pan for the anled 9.2 that I have where could I buy a new one for it .. I thank you very much from Michigan..Thanks for the video
@BRUCEFORCE82
@BRUCEFORCE82 11 лет назад
Rockcreek Consulting out of PA
@stefanivassvika
@stefanivassvika 10 лет назад
my problemmed oil level is solved now, now I wonder if you know what the valve clearance should be. The engine is running now.
@haroldweis2741
@haroldweis2741 6 лет назад
I have one on a Ditch Witch, I put a carb kit in and got it started, but the next day it won't start. i have had the carb off several times and am sure there are no plugged passages. Any help would be greatly appreciated.
@BRUCEFORCE82
@BRUCEFORCE82 6 лет назад
Harold Weis did you clean or replace fuel filter?
@jamesreeder5316
@jamesreeder5316 2 года назад
I have an engine given to me by a friend. It has a hand crank. And odd kind of a head. Don't know what it is.how can I get a picture of this to you so you may be able to know what it is?
@BRUCEFORCE82
@BRUCEFORCE82 2 года назад
Email bbarker1982@gmail.com put your name in subject
@jameswaltz8473
@jameswaltz8473 5 лет назад
Hello, I have this exact engine and i notice this sound when i pull it over. I noticed yours does it too. What is that and is it suppose to be there?
@BRUCEFORCE82
@BRUCEFORCE82 5 лет назад
The spring coupling on the magneto makes that snap/clunk noise. It adjusts the ignition time on engine and also helps with starting. The only magneto engine I have had that didn't clunk had a broken spring and could not start
@nicksnextproject535
@nicksnextproject535 Год назад
Did it have babbit bearings in the lower end?
@BRUCEFORCE82
@BRUCEFORCE82 Год назад
Yes
@donvoll2580
@donvoll2580 7 лет назад
Good day. Nice job on motor. What is a motor like that worth? Thanks.
@sergiosalazardiaz6100
@sergiosalazardiaz6100 5 лет назад
Don Voll tengo un motor igual quisiere saber de cuantos caballos de fuerza es grasias
@vancester1st
@vancester1st 7 лет назад
What type of gas do you use? I think these were designed for leaded fuel.
@BRUCEFORCE82
@BRUCEFORCE82 5 лет назад
I use unleaded 87, or true fuel if I dont have cork gaskets on carb or fuel filter
@JoshKilen
@JoshKilen 5 лет назад
I used unleaded 87, with lead additive, this year I will be running 91 non ethanol with lead additive.
@haroldweis2741
@haroldweis2741 6 лет назад
Yes, I replaced the sediment bowl with an inline filter. It is getting gas but when trying to start with the choke on it won't start. I have pulled the plug and it is dry.
@BRUCEFORCE82
@BRUCEFORCE82 6 лет назад
Harold Weis open the low idle and high idle jet screws at least 3 turns and see if it starts. With choke on and rotating engine a few times should soak the air intake with gas. If it is still dry, make sure the float bowl is filling up properly. I replaced my carb because I found a hair hairline fracture causing a vacuum leak
@timsmith3339
@timsmith3339 6 лет назад
How did you rebuild the mag. Have one with no spark.
@BRUCEFORCE82
@BRUCEFORCE82 6 лет назад
Tim Smith , most of the time its the points needing a cleanup or replacement
@donaldwiningar3323
@donaldwiningar3323 5 лет назад
No spark on mine
@donaldwiningar3323
@donaldwiningar3323 5 лет назад
Points are clean looks good. But no spark
@tcmits3699
@tcmits3699 2 года назад
Check condenser too
@rgohil65
@rgohil65 8 лет назад
Where did you find all of the parts to rebuild the engine. I have one on a ride on asphalt roller which I would really like to have rebuilt as well but dont know anyone here in Arizona who can rebuild it and do it as well as you have done it.
@BRUCEFORCE82
@BRUCEFORCE82 8 лет назад
RockCreek Consulting, looking for his contact info, he sells on ebay and direct. I was able to get piston, rings, connecting rod, magneto parts and carb parts.
@rgohil65
@rgohil65 8 лет назад
how much did the entire rebuilt cost you? I need to find a rebuilt AENLD for a ride on roller. Let me know if you know of one.
@BRUCEFORCE82
@BRUCEFORCE82 8 лет назад
It's been awhile, guessing a few hundred including repainting and misc tools. The parts couldnt have been $200.00 Runs like a champ. In the video it took a few pulls, but tuned its one or 2 pulls. I prefer these over the new engines from other companies
@rgohil65
@rgohil65 8 лет назад
Can you come to AZ and do mine please? :)
@garybiggs9010
@garybiggs9010 7 лет назад
Got room in that boat? I have a AENLD in a Gilson mortar mixer I need to get running. Thanks for making the video on this.
@jollyranchhand
@jollyranchhand 7 лет назад
What air filter element do you use on that engine? I have the same engine but can't find a suitable filter.
@BRUCEFORCE82
@BRUCEFORCE82 5 лет назад
I recently switched to the original oil bath filter. I picked up the paper filter in this video from napa, I dont recall the number.
@clebersusluz3126
@clebersusluz3126 Год назад
É A DISEL OU GASOLINA???
@BRUCEFORCE82
@BRUCEFORCE82 Год назад
Gasoline
@baileydonahue7314
@baileydonahue7314 11 лет назад
Where did u get the magneto spark plug wire mines shot and I can't find one
@BRUCEFORCE82
@BRUCEFORCE82 5 лет назад
Rock creek consulting in PA
@junkman6261
@junkman6261 11 лет назад
Where did you get your rebuild kit or parts?
@BRUCEFORCE82
@BRUCEFORCE82 5 лет назад
Rock creek consulting. I recently worked on this engine again, found mag, carburetor, correct fuel tank and oil bath air cleaner all new old stock on ebay
@stevepotts2116
@stevepotts2116 4 года назад
I, HAVE A, WISCONSIN, MODEL, ACN,.,,, I, NOW YOU, CAN GET A, GENERATOR FOR THE, WISCONSIN, THAT ALSO, WORK, S AS, A STARTER I, HAVE A GENERATOR OF, A, SRAIT , 6, PONTIAC,,, THAT, I, WILL TRY TO MOUNT TO, THE SIDE OF THE WISCONSIN DEPENDS UPON YOUR PROJECT IF, YOU CAN USE AN, ELECTRIC SET UP, LIGHT, S BATTERY AND GENERATOR /STARTER
@davejohnson2937
@davejohnson2937 2 года назад
hey sounds great i have same engine but yet to hear it run magneto needed rebuilt not has great spark but it wont start... any vids on setting magneto timing?
Далее
Wisconsin AENL Engine Revival
1:06:15
Просмотров 876
Will It Run? Antique Wisconsin engine from a barn.
1:00:47
I Make This Tiny 2-Stroke Engine From Scratch
31:59
Просмотров 1,3 млн
Will the OLD Backhoe Start & Drive? (It might be SCRAP)
1:36:47
Brief overview of Wisconsin earlier engines.
7:24
Просмотров 25 тыс.
Wisconsin AEN, looking inside
8:17
Просмотров 5 тыс.
Epic Wisconsin Engine Total Rebuild
50:19
Просмотров 160 тыс.
Agricat - Wisconsin engine disassembly 6/1/23
16:22
Просмотров 1,4 тыс.
Atomic 4 - Zenith carburetor troubleshooting
12:39
Просмотров 68 тыс.
1958 Wisconsin AENLD Revival
39:48
Просмотров 333