No video :(

WLtoys 1/28 RWD Drift Update 2 - More Steering

Подписаться 27 тыс.

Просмотров 93 тыс.

50% 1

How to easily add more steering angle for WLtoys 1/28 RWD drift.
The result is surprising!
However this tutorial turns out to be much longer that I expected.
Links & Stuffs:
Important tutorial of how to disassemble swing shaft: • Disassemble Mini-Z Swi...
How to make monoshock (original video by Marixor) • Wltoys 1/28 Drift Mono...
Tamiya Mini 4WD Screw Set A (15232)
www.1999.co.jp...
Gyro: I use Slidelogy and choose a horrible colour so it's a bit cheaper than other colours.
www.rcmart.com/...
You can help supporting this channel by purchasing from Banggood with these afffiliate links.
The price will be the same, all discounts and promotions are applied as normal.
Ball studs and linkages are from this Sinohobby kit: goo.gl/vTjbFh
The car in this video is WLtoys 1/28 chassis.
Touring/Rally Car, K989: bit.ly/2Vr4fWQ
Drift car, K969: bit.ly/2znqnbb
#WLtoys #RWD #Drift
Project playlist: • WLtoys K989/K969 RWD D...
0:00 Introduction
0:37 CENTRE SHAFT
2:06 ELECTRONICS
4:11 BULKHEAD MODIFICATION
4:59 STEERING KNUCKLES MODIFICATION
6:33 MONOSHOCK
8:47 SERVO INSTALLATION
9:03 GYRO INSTALLATION
9:24 RESULT

Опубликовано:

14 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 185

@BeaversHobby 5 лет назад

Time Stamps Premise of this project: 0:23 Centre shaft mod: 0:36 Electronics installation: 2:04 Steering/servo mod: 3:17 Bulkhead mod: 4:10 Steering knuckle mod: 4:57 Monoshock: 6:31 Servo installation: 8:46 Gyro installation: 9:02 Final result: 9:23 Test drive: 10:17 Conclusion: 10:44

@cheshirerc 2 года назад

Q QA pa

@florenciodavid7654 Год назад

Pmmm

@weslieoomph2606 5 лет назад

I love your videos on the Wltoys k989 build thank you for all your work I’ve been having so much fun with my K989 thanks to you.

@That1E_K1129 5 лет назад

very very crafty buddy. always coming up with new cheap tweaking methods. A++

@bilbine5766 5 лет назад

YASS! been waiting for this series so much, since im also going to do this conversion

@BeaversHobby 5 лет назад

I'm also glad it's finally up and running. This car has been sitting in pieces for months.

@cheddarcheese8945 5 лет назад

Haha ive been watching your channel the day or so binge watching video after video , good work man awesome to see mini rwd ,i just ordered one last week but im in nz and shipping takes a whole month haha buy then should have plan set also going to convert to 1/24 scale to suit rx-7 model i built

@Handlefosho 4 года назад

Giving me inspirations for mini z rwd. Thanks always 🙏🏽

@Trifle165 4 года назад

SUN JAE LEE Hey man, do you have any stl files for making a RWD drift Mini z?

@sontoshi25 5 месяцев назад

Hey man! Thanks again for this vid, I'm binge watching literally everyday and learning alot from you. Quick question though, do you know if upgrading to metal steering cups/knuckles is better than plastic? Because mine keeps on breaking, it's the 2nd time already in a month, and ordering each time I break the part is kind of frustrating. (I accidentally keep on breaking it when removing the link rods, I don't know a better/efficient way than converting to metal. What do you think?

@BeaversHobby 5 месяцев назад

Yes, the knuckle is a good upgrade to improve the durability. However make sure the ball heads are OK and don't have thick collar otherwise they will get stuck and won't have full movement for the suspension. You might have to grind the underside of the ball heads down in that case.

@dankforest Год назад

I have an old Tamiya Fox (renamed NovaFox) its a rwd buggy 1:10. It has an awesome oldschool brushed motor(revolution losi) im thinking of coverting it to a drift car. Its really fun with drift tires. So i think if i add gyro and replace servo and all but engine it will glide. BUT it wont be original 1984. Should it do it or leave alone?

@BeaversHobby Год назад

That's a tough question. Personally I'd leave it be because it's a vintage Tamiya and I have a soft spot for that. Then it'll get something like 3Racing Sakura D5 for RWD drift.

@almightyalan8942 5 лет назад

Personally since it's small I would reduce Ackerman to hold angle longer at higher speeds, I repositioned the hole where the steering rods connect to the wheel hub, try to have positive toe into parallel toe at full lock. Just my opinion

@BeaversHobby 5 лет назад

Thanks for the suggestion. I'll look in to that.

@AllaboutTheWoodrows 2 года назад

Dude your ideas or knowledge is on point

@bernietsan5538 4 года назад

late to the scene...thank you for all the videos! :)

@Shan-ij7rs 2 года назад

Nice bro

@theghaniya 4 года назад

Thanks bro very helping, im trying to convert mine. Specially on steering system

@brianstevens2244 3 года назад

Where can I get the servo horn. I have everything else, please help or point me in the right direction

@BeaversHobby 3 года назад

It's from afrc 5g servo or powerhd 5g. However the angle is not enough and in the end I made my own extension to a straight horn. Check out part 3 and 4 for more info.

@wasabipet67 4 года назад

So crazy !! But work !! I understand !! Thank you very much!!

@jensv.791 3 года назад

Hey beaver würde es was bringen auf der Hinterachse auch ein monoshock System zu installieren?

@BeaversHobby 3 года назад

I've seen people doing it. I guess it's for rolling effect but I don't know how effective it is for controlling the car. I do monoshock on the front so I can have more clearance for steering. The rear doesn't need that.

@killahkay2112 4 года назад

you are crazy man !!!! that is Awesome !!!!

@harryfp1494 4 года назад

I had an idea last night for a third bearing system that would hold the stock cut driveshaft in a bearing cup that is screwed into stock motor sper plate

@BeaversHobby 4 года назад

2 bearings would do if the shaft is short enough. You only need the front and the back of the shaft and it got that already. I just cut my screw really long.

@pinkfactory2667 4 года назад

is it possible to increase the steering angle without doing all this, is it that just by cutting the part of the cell and moving the pivot point of the ball joints this could be enough?

@BeaversHobby 4 года назад

Unfortunately, no. Simply moving pivot point isn't enough for RWD drifting. Even this is still not enough and you can see in my 3rd update how to make enough steering angle. However you don't have to move the servo if you don't want, just make the horn long enough and it should be fine.

@tylerseabook9423 3 года назад

This is awesome info.

@tylerseabook9423 3 года назад

Love your vids man.

@HeySkipper 5 лет назад

Hi beav! I ordered 2 mini q ball diff for the WLTOYS k989. Do i need special cups or the atomic universal shafts to install them? Can you post a link of the items i will need to get the ball diff in? You have been so helpful with these cars:) thank you for sharing your knowledge.

@BeaversHobby 5 лет назад

Yes, you'll need long swing shafts. Atomic's are constantly out of stock most of the time so I also give you the link for RC-Aurora www.miracle-mart.com/store/index.php?main_page=product_info&cPath=67_74_1029&products_id=13988 ppm-rcracing.com/products/Wide-Crooked-Angle-Universal-Shaft-for-Mini%252dZ-%286061-Black-x-4-Pcs-Long%29.html

@SteliosRcdrift 4 года назад

My friend,try to have more parallel steering and more linear throttle control.my advice is dont put too much caster as it will upset the balance and your difficulty will increase.my humble opinion

@BeaversHobby 4 года назад

Thanks. This car has been modded to it's maximum setting in my next videos. I don't know if you've seen it yet, here's my final update. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-CUZIcDH5P6g.html Thanks for the suggestion about caster by the way. I also find excessive caster makes it harder to drive. I also dialed down the caster on my DRZ.

@jumpstartrc1571 5 лет назад

sweet i like I may buy another wltoys 1/28 car. my x power micro mit should be coming in any day and I will make a video of it

@BeaversHobby 5 лет назад

Looking forward to that.

@haydnholder7090 Год назад

How do how get the front to grip like that? No matter what more weight or less weight and steering input the car just goes straight, ive got a ton of angle and everything just can't get the front to grip

@BeaversHobby Год назад

If no matter what you do the front just won't grip then you'll have to check the tyres contact and possibly put M2 screw into the lower arm to adjust the ride height and in turn, tyre contact.

@haydnholder7090 Год назад

@@BeaversHobby thanks Ill give it a try! The ride height in the front is pretty low would it help if i rased it, im running a concrete in the garage maybe the front of the chassis is dragging on the uneven surface 🤔

@BeaversHobby Год назад

@@haydnholder7090 It's really hard to run this car on a rough surface already so getting RWD drift to work is going to be difficult. Anyway, check the front contact is the main thing. You'll need it to have tyre contact when you turn. The ball cap on the steering could be too tight and it pulls the arm up too so check that as well.

@haydnholder7090 Год назад

@@BeaversHobby sweet thanks bro! Just installed a losi micro front shock and cut those chassis tabs off way more clearance in the front now an alot smoother up an down movement, what surfaces would you recommend to be the best to run it?

@BeaversHobby Год назад

@@haydnholder7090 Anything smooth will do. Wooden floor or table or marble/polished concrete are also good.

@dilabbila9225 5 лет назад

Mod the steering still make me confuse😂 can i use gyc 300 gyro??

@BeaversHobby 5 лет назад

GYC300 probably works. You can try but I don't know how fast it responses. As for steering modification, there are 5 steps. Starting from 1. doing up the servo horn with 2 holes at the top. 2. Cut the back off front bulk head. 3. Mod the steering knuckle. 4. making monoshock. and 5. stick the gyro down.

@dilabbila9225 5 лет назад

@@BeaversHobby okay thanks.. i wanna try....

@loga_912 2 года назад

Hey, is there any other mods to make more steering angle in the k989? I want to keep it 4wd but wanting more steering angle. I changed the ballhead position from the servo horn. Is there any other ways?

@BeaversHobby 2 года назад

Make monoshoock for more clearance. You can also move the steering ball on the knuckle forward.

@GrozerVonTeplitz 5 лет назад

Nice build

@cheddarcheese8945 5 лет назад

How does it drive compared to the atomic rwd

@BeaversHobby 5 лет назад

It's still far off. This one only slides without spinning. Too violent with the control and there's no way to recover unlike Atomic DRZ where I'm in control most of the time.

@fuzzypunk1632 5 лет назад

amazing job man!

@tomwright943 4 года назад

Hi beaver😊👍, I am just wondering....... is there a particular reason that not many people seem to do the mono shock mod on the rear of these cars? Thank you

@BeaversHobby 4 года назад

I think because the wheels are not really independent to each other so the handling will be compromised. The main reason to do this is to move the shock away from steering.

@tomwright943 4 года назад

Ok thank you 😊👍

@valentinorossidin4803 4 года назад

hey dude, what is the option for beginner drift, awd or rwd?

@BeaversHobby 4 года назад

AWD. It's much easier and it's not expensive.

@valentinorossidin4803 4 года назад

@@BeaversHobby thanks dude, wait for your new video 😉

@BeaversHobby 4 года назад

@@valentinorossidin4803 My pleasure.

@cityofplant 3 года назад

Do I need to install gyro for rwd to work properly? My car just spin out without one.

@BeaversHobby 3 года назад

Yes, a gyro is necessary for RWD drift.

@jab84r 2 года назад

Sameeeeeee

@ilud2007 5 лет назад

Nice project!

@bharafelder 5 лет назад

Lmfao I’m waiting forward to Xmas,also can you make like a cinematic montage vid

@BeaversHobby 5 лет назад

Thanks fir the suggestion. I gotta lay down a course first.

@krystiancalderon3930 3 года назад

Hi do I have to make or cut the center shaft to make it rwd ? Or I can just take it out and put nothing in it ?

@BeaversHobby 3 года назад

You can do that or just do what I did, find another 2mm shaft and file the end off to make a flat spot so you don't destroy the original part.

@krystiancalderon3930 3 года назад

@@BeaversHobby thanks I will do a rwd conservative after I fix some problems on the wltoys first

@Funcentric 4 года назад

Nice setup. What is the difference between an external gyro like the one you have vs one that’s built into the receiver? Any advantage of an external one? I have a fly sky FS-BS3 on the way and wondering if an external gyro would be better and if so, how.

@BeaversHobby 4 года назад

Separated gyro unit is usually more responsive and accurate than built-in. However I haven't tried the new stuffs yet and these are what I know based on my experience with old stuffs. New ones like FS-BS3 and RC4GS might work just as good already.

@Funcentric 4 года назад

@@BeaversHobby I see. Okay, thank you. I did some further research and found that the external gyro allows adjustability within the unit itself whereas the ones built into the receiver are controlled only by the transmitter.

@BeaversHobby 4 года назад

@@Funcentric Some expensive gyro can adjust endpoint independent to the transmitter too.

@hayatonanri2536 4 года назад

What brushless motor did u use in this project ? And Esc tnx !

@BeaversHobby 4 года назад

I use Surpass 1410 brushless motor and XC-10A ESC in this project. However this setup is obsolete now and I highly recommend Surpass brushless combo. www.aliexpress.com/item/4000900570121.html

@gtrckt 3 года назад

Hi Beaver, at 7:00 I saw your upper swing arm was modified. Do you think it's important to include the mod to increase caber for front wheel?

@BeaversHobby 3 года назад

Not really. Standard camber will do fine. This is carried over from my previous project.

@gtrckt 3 года назад

@@BeaversHobby I’m relieved that I don’t have to do this mod. But isn’t a lot of RWD cars (eg atomic DRZ) shows quite a bit of front wheel camber?

@BeaversHobby 3 года назад

@@gtrckt Yes, but it depends on chassis to chassis and driver's preference. Some of them just work with 0 camber. You can also use rounded POM tyres instead as well.

@gtrckt 3 года назад

@@BeaversHobby Thank you. You are an invaluable resource to RC community.

@chrisbenson15 2 года назад

Bro what if the gyro vibrates?

@BeaversHobby 2 года назад

It might get some bad reading and the wheels will shake back and forth when it counter steer. The wheel shake can come from something else too but we'll always check if the gyro is properly mounted first.

@tirandodelcarro6827 5 лет назад

I love it

@justinaldrich692 5 лет назад

I love these vids you did on the 1:28. I would love it if you could please please do some on the Wltoys A242 1:24.... I'm brand new to RC but definitely have the bug. Thanks for taking the time and making the videos for us.

@BeaversHobby 5 лет назад

Sorry, I have no plan for 1/24 at the moment. I might change my mind later though once I run out things to do on 1/28.

@justinaldrich692 5 лет назад

@@BeaversHobby I hear you, good point. Keep on having fun. Thanks again for sharing.

@juanmanavarro3817 3 года назад

I make the same upgrade and i cant control the drifting is imposible someone can Help me i sent video samething is wrong i think

@BeaversHobby 3 года назад

You'll need a gyro and more angle than in this video. I later made some changes in the part 3 and 4. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KXmDLnptEgU.html ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-CUZIcDH5P6g.html

@savneetsinghrairai6823 4 года назад

Your frount stering alignment is out use lazer pointer used to align real car wheels ...they must be in paraell

@BeaversHobby 4 года назад

Any tool you use in particular? It's almost impossible to find tool for 1/28 at reasonable price (only people who have it are hard-core racers). So I just use MIT setup sheet for toe and 1/10 tool for camber. BTW, this is RC drift so you'll see a lot of toe out and camber. Parallel alignment is a rare sight.

@aliffaslam7289 4 года назад

Sir, the servo horn where did u buy it?

@BeaversHobby 4 года назад

You can get the same one in AFRC bit.ly/38sCLr2 . However you will find out in part 3 of this series that it's not enough for RWD drifting and Ackerman + toe angle weren't good so I had to make my own extension ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KXmDLnptEgU.html .

@lacemi 4 года назад

Hello, What do you use for the ground?

@BeaversHobby 4 года назад

My floor is some sort of plastic-rubber tile. It's just regular room floor.

@________GHOST________ 2 месяца назад

Hello where do I find that servo horn you have in this vid thanks

@________GHOST________ 2 месяца назад

Hhhh

@BeaversHobby 2 месяца назад

@@________GHOST________ It's usually bundled with a servo. Last time I got it with the AFRC D1802MG servo. Still, this is not the best horn to do this modification. You're better off with a custom horn like I did here (it's update 3). ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KXmDLnptEgU.html

@goingcrazy00 4 года назад

Does this shock mod make it more able to fit mini z bodies? And you could get it a couple mm lower if you remove the nuts on the bottom on the ball head and cut the shaft of the ball head by 2mm.

@BeaversHobby 4 года назад

No, the monoshock actually makes the front higher at the bulkhead/gearbox area. To make the front lower to fit Mini-Z bodies is lowering the front shock tower like this one. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE--gCJEXXWBEo.html

@goingcrazy00 4 года назад

@@BeaversHobby but then you can't get the steering angle because the shock is in the way right?

@BeaversHobby 4 года назад

@@goingcrazy00 If the wheels has a bit of offset like 1.5 it'll get enough steering to drift in AWD. Doing monoshock is for extreme steering angle in case you do CS mod at high ratio, eg. more than 2.0 (rear wheels spin 2 times while the front spin 1 time).

@goingcrazy00 4 года назад

@@BeaversHobby you still do the C's mod on RWD? Don't you remove the dif in front and remove the center shaft for RWD?

@BeaversHobby 4 года назад

@@goingcrazy00 The CS mod is only for AWD. I'm sorry I was confused from talking you you in the previous video with out of the box K969 and all. For RWD, yes, this shock configuration is one of the few ways you get enough steering. Otherwise it won't work. However it's even harder to fit a Mini-Z body. ps. I'm still waiting for Camaro ZL1 to come out though. That one should be great on WLtoys.

@derekhe148 2 года назад

where did you get the spacers?

@BeaversHobby 2 года назад

Tamiya Mini 4WD parts. You can also find them from other make like 3 Racing like this. www.3racing-parts.com/tamiya-mini-4wd-2mm-spacer-set-black-3racing-m4wd01bk-p-90069636.html

@derekhe148 2 года назад

@@BeaversHobby dude you are literally a god send. always replying fast too. definitely the best channel on youtube for all things mini drift rc related

@glowiever 5 лет назад

Isnt that too much toe out? Also looks like too rear-heavy though

@BeaversHobby 5 лет назад

Yes, toe is too much because the linkages I use can't extend too far. I really have to do something about it. Rear heavy is pretty nice though. I saw a lot of people hanging the battery at the back but didn't think it'd help until I tried. It makes the car a bit lazy to go in to drift and slow to in transition. But it's more stable and won't spin as easily.

@nameless2346 5 лет назад

Beaver's Hobby you can probably make a custom steering arm using extended servo horns.

@BeaversHobby 5 лет назад

@@nameless2346 That's what I'm going to do. But it'll need a bit of experimenting with length and width first.

@nameless2346 5 лет назад

Beaver's Hobby cool. Can’t wait

@Jonsonkonde 5 лет назад

สุดยอดครับ

@airellhafidz3266 3 года назад

How long is that two linkage from the servo and the hub

@BeaversHobby 3 года назад

In the final version the length is around 16mm-18mm if I remember correctly. It's toe angle. You can set it up however you like as long as it's toe out, the wheels are pointing outwards.

@airellhafidz3266 3 года назад

@@BeaversHobby Thank you very much

@BeaversHobby 3 года назад

@@airellhafidz3266 My pleasure. Good luck with the project!

@airellhafidz3266 3 года назад

@@BeaversHobby hey i have trouble with servo placement and i have followed the linkage lenght....but the angle is not what i tought it would be......should i buy the mini q rear linkage or servo cuz the origanal servo had no much angle.....i got the linkage from wltoys a959b....i cut the linkage and put it back together and follow the length that you have given.

@BeaversHobby 3 года назад

@@airellhafidz3266 You can try and change the servo to another one. Also what radio are you using? Some radios don't output much servo movement.

@bigblockbumpside2296 2 года назад

Where do you find the servo horn??

@BeaversHobby 2 года назад

It comes with the servo. If you buy something like this AFRC bit.ly/38sCLr2 it'll have horns including the one in this video.

@bigblockbumpside2296 2 года назад

@@BeaversHobby thank you!

@bigblockbumpside2296 2 года назад

@@BeaversHobby i actually already have a servo very similar to that. Is there a place to get just the servo horn?

@BeaversHobby 2 года назад

@@bigblockbumpside2296 Unfortunately, no. And this is not it's final form. I ended up using the standard one (straight one) and made my own extension in the next step. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KXmDLnptEgU.html

@jademd15 4 года назад

Have you modded the upper control arms at all for the steering mod?

@BeaversHobby 4 года назад

Yes, I modded my upper arms to be to adjust the length for camber.

@jademd15 4 года назад

@@BeaversHobby is that in this video? (have I completely missed it 😂)

@BeaversHobby 4 года назад

@@jademd15 Actually, it's a very old video that I did with the toe bar, apply the same method with the upper control arm and you'll get adjustable camber. By the way, use M2 screw instead of M1.5 for better strength. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-9OlVz1dXJNc.html

@jademd15 4 года назад

@@BeaversHobby awesome thank you!

@BeaversHobby 4 года назад

@@jademd15 My pleasure. Good luck with the project.

@Artski4000 4 года назад

hi, do you know what servo horn you used. Thanks!

@BeaversHobby 4 года назад

It's from standard 5g servo. I think the yellow one is from PowerHD 1600A. I use it because I've already drilled it. Gening D561MG also gives you some horns.

@Artski4000 4 года назад

@@BeaversHobby thanks for the reply, you really inspired me to take on this project. just wondering what offset do you have for your front and rear tires?

@BeaversHobby 4 года назад

@@Artski4000 In this video I use 0mm offset narrow wheels on all corners and Mini-Z drift tyres narrow MDT001.

@Artski4000 4 года назад

@@BeaversHobby Thank you for the help, would you recommend this combo for this build www.aliexpress.com/item/32838629176.html?spm=a2g0o.cart.0.0.30f43c00tn9OVG&mp=1

@jackshatau7525 4 года назад

Can you give your email? I need some help. I made cs and it worked well. Then i made rwd and it can't drift :( i dont understand why :(

@BeaversHobby 4 года назад

Here's my email beavershobby@gmail.com And if you want more rapid response then facebook is probably better facebook.com/beavershobby/

@ernest_4104 4 года назад

5:49 lol

@earthtoys5232 2 года назад

เท่มาก

@danielfarber8696 4 года назад

That servo horn looks very wierd

@BeaversHobby 4 года назад

This is horn from PowerHD 1600A. It has 2 top holes side by side which I thought it would be perfect. As it turned out, this still hasn't got enough steering.

@danielfarber8696 4 года назад

Hey thanks now i know and one question

@danielfarber8696 4 года назад

What is the best drift car i should buy for my house in quarantine i have a basketball court in my base ment so i have space to drift but i dont know if i want the mini z or the wltoys

@danielfarber8696 4 года назад

Witch one do you prefer

@danielfarber8696 4 года назад

Just for a video idea there is a HBX 1/18 drift car it might be good or bad that’s why i watch your vids for upgrades builds,etc

@esmokebaby 3 года назад

Damn covid got everything taking long time or out of stock

@BeaversHobby 3 года назад

You can search for alternatives. The main parts are 3.5mm ball heads and ball caps, M2 screws and spacers.

@esmokebaby 3 года назад

@@BeaversHobby ok thanks

@BeaversHobby 3 года назад

@@esmokebaby My pleasure.

@esmokebaby 3 года назад

@@BeaversHobby been trying to find a 3d print stl but no one nice enough to give me one lol

@BeaversHobby 3 года назад

@@esmokebaby I think in this group would have someone doing the 3D printed chassis. Check it out. facebook.com/groups/296354234301053

@TorKungChannelRC111_Retrogames 5 лет назад

ผมเข้านิ้วไปแล้ว 555พาด จนได้

@user-ev2jy5ih4k 5 лет назад

มีดคมจังอยากได้มาไว้เเล้วก็พวกหัวสว่านอ่ะครับถ้าจะซื้อต้องซื้อที่ไหนครับเเล้วชื่อเรียกว่าอะไรว่าอะไรครับ

@user-ev2jy5ih4k 5 лет назад

เเล้ไจโรมันช่วยให้อะไรดีขึ้นเเล้วดีขึ้นมากกว่าเก่าไหมครับ

@BeaversHobby 5 лет назад

มีด Art knife ของ Olfa ซื้อจาก B2S ร้านขายเครื่องเขียนอื่นก็น่าจะมีครับ ส่วนสว่านมือ กับดอกสว่าน ได้มาจากอมรครับ ดอกสว่านซื้อมาหลาย ๆ เบอร์หน่อย พวกเล็ก ๆ แบบ 1, 1,5, 2 มิล

@BeaversHobby 5 лет назад

ไจโรช่วยให้รถไม่หมุนครับ ถ้าขับ 4 ไม่จำเป็น แต่ดริฟท์ขับหลังต้องใส่ ไม่งั้นหมุนตลอด

@user-ev2jy5ih4k 5 лет назад

ล้อของอะไรครับสวยดีขอเว๊ปซื้อหน่อยครับ

@BeaversHobby 5 лет назад

ล้อของ Mini-Z ตัวธรรมดาเลยครับ ออฟเซ็ต 0 สีเทา แนะนำติดต่อร้าน RC บ้านนอกครับว่ามีไหม facebook.com/RCBHobby/ ของผมสั่งมาจากนอก ตอนนี้หมดแล้ว banzaihobby.com/Kyosho-MDH100G-N0