Yamaha FZ6 Fazer Wheel Bearing Replacement

Подписаться 2,9 тыс.

Просмотров 6 тыс.

50% 1

Hello folks!
In this video I will be replacing the rear wheel bearings on a Yamaha FZ6 Fazer.
If you found this video helpful then give it a thumbs up, consider subscribing to my channel and don’t forget to hit the bell icon so you don’t miss out on future videos.
Take care and I’ll se you in a bit!
My Fav Tools:
Bahco 34pc Socket set: amzn.to/35kcM3m
Bahco 104pc Socket set and spanners: amzn.to/2nvrX8P
Wera 6pc Screwdriver Set: amzn.to/2AWGuxa
Teng Tools Torque Wrenches:
40-210 Nm: amzn.to/35lKs0j
20-100 Nm: amzn.to/35lKuVZ
5-25 Nm: amzn.to/33fv83G
Support me on Patreon: / thegarageuk
You can also follow me on the socials:
Instagram: @nandorsgarage
Facebook: / nandorsgarage

Опубликовано:

15 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@laszlobauer5274 4 года назад

This turned out to be very funny!

@TheGarage2018 4 года назад

Lol :)) thanks

@garethstarkey7560 3 года назад

What you should do is heat the carrier to about 150deg c and freeze the bearing and it then should just drop in

@cupcayuk 3 года назад

Cheers mate

@nikoslion6213 4 года назад

Greetings from Greece! What is the type/code of the rear wheel bearings? Is it an fz6 of 2004-2006?

@TheGarage2018 4 года назад

Yes, it’s a 2005 FZ6. I’m not exactly sure what the bearing codes are as I bought them as a kit, but let me see if I can find the old ones and I’ll give you the codes.

@danielsale3805 Год назад

Try putting a fine layer of grease on the outside of the bearing before you hammer it in and preferably use a rubber mallet and guide it in with the old bearing like you was doing.

@walijumaat2158 Год назад

where is the video part of you removing the needle bearing? did i miss it or something

@loganmanuel6731 4 года назад

Hey man quick question, should I be hitting that needle bearing all the way down to that lip in the center of the wheel? or is there a specific measurement? My service manual doesn't mention a single thing about installation of this.

@TheGarage2018 4 года назад

Yes you need to drive the needle bearing all the way down to the lip.

@loganmanuel6731 4 года назад

The Garage thank you so much! It’s always nice to see fz6 specific maintenance videos on here!

@TheRyanheisner 3 года назад

How did you remove the old needle bearing ?

@TheGarage2018 3 года назад

I used the same blind bearing puller kit I used to remove the other bearings. Thanks for watching and good luck!

@unclebishoppeskitchen5838 Год назад

instead of cutting the old bearing in half just grind down the outer diameter so it will fit without getting stuck.

@TheGarage2018 Год назад

Good shout! Thanks for the tip!

@melindareusora5138 3 года назад

What size of bearing that

@TheGarage2018 3 года назад

I don’t know the exact size I’m afraid, I bought them as a kit for the FZ6. I don’t have the old ones either to check for the size.

@thekbshouse Год назад

God it's hard to look you banging metal on metal, not heating the iron long enough, not freezing the bearing, levereging metal on metal and brute forcing the bearing without evenly applied force. If you are looking how to do this for this bike, look another video on how to use the tools without damaging your wheels and new bearings and then maybe see how to tackle this bike specifically, changing the needle bearings as well as lubricating everything.