1988 Dodge D150 Truck Power Steering Gear Box Input Shaft Seal Replacement.

Подписаться 744

Просмотров 3,2 тыс.

50% 1

I had to replace the Power Steering Gear Box input shaft seals on my 1988 D150 truck because it was bleeding red really bad. The first seal kit I got from O'Reilly Auto parts was wrong so I had to drive my Jeep 50 miles back to the store and return it for the correct one. It was a pretty east job and took about a hour of shop time.
The 88 fuel injected Dodge with a 318 motor and a 904 transmission is a Southern New Mexico truck with not a spot of rust and solid everywhere, all the bolts come off like it just left the show room floor.

Авто/Мото

Опубликовано:

29 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 16

@blakenorman4822 4 месяца назад

Man i dig these trucks, i tore apart a junked title 87 d150 in my driveway and put the suspension on a 47 1 ton dodge panel truck, the redtop brand new steering box is leaking from input shaft after 500 miles, wtf, also got a 85 d150 put new heads headers 4 barrel intake holley 650 90,000 on 318 runs like a top, thanks for video

@desertdogsgaragemetalworks3843 4 месяца назад

No problem glad you like it. I like old school also and easy to work on.

@ryanquerec3051 6 месяцев назад

Thank you sir! I have an '86 that was almost identical, procedure was the same. Couldn't have done it without you. Top nut was one piece with bearing.

@desertdogsgaragemetalworks3843 6 месяцев назад

I'm glad I could help.

@danielworden4695 3 месяца назад

Thanks now i have the confidence to do it🎆

@Hectorico 2 месяца назад

Not all hero’s wear capes!!!

@briansignorelli7090 7 месяцев назад

Good video I'm going to have to do this to my 85 as well

@desertdogsgaragemetalworks3843 7 месяцев назад

Ya I also now have to do the Pitman Shaft Bearings and Valve seals.

@ericshinault3628 6 месяцев назад

Fixin to do that tomorrow. Figure I'll be cussing, busting knuckles and drinking beer. Hope youins are doing well 🙏❤️ from NC

@desertdogsgaragemetalworks3843 6 месяцев назад

Ya I don't think my hands ever heal.

@jeffvaughan6363 Год назад

Old iron is good iron!

@desertdogsgaragemetalworks3843 Год назад

Got that right.

@daniellarkin9182 Месяц назад

What do you do if the seal doesn’t want to come out?

@desertdogsgaragemetalworks3843 Месяц назад

What time in the video are you asking about?

@daniellarkin9182 Месяц назад

@@desertdogsgaragemetalworks3843 at 11:39 when you use the screwdriver to pop out the thicker inner seal. Mine won’t budge at all.

@desertdogsgaragemetalworks3843 Месяц назад

@@daniellarkin9182 Interesting its in there good then. It should come out, it is just tapped in with a hammer and socket and you can destroy it by pulling it out it won't hurt nothing and you just replace it with the a new lip seal and make sure you put the new seal in with the lip facing toward the inside of the gear box, You can RU-vid that kind of seal install, Just be careful that you don't tear up the cap that you are pulling it out of because that is the important piece you need, Most seals like that are normally destroyed when taking them out so you are not doing any thing bad mine just came out easy. Its not a bad idea also when installing that kind of seal only, to clean all surfaces and put some sealant on the outer round part of the seal before installing. Just helps it stay in there. Hope this helps good luck and be patient.