2006-2019 GSXR 600/750 Stator and Stator Cover Replacement 

You don't put loctite on the 8mm's that hold the covers on do you? Just the ones holding the stators?

i just bought my first bike a week ago. Stator Cover was JB welded and Gasket maker all over it. Yeah i should've looked better but Thanks to this video i was able to tackle the repair/replacement with confidence. Great video, Thank you!

Very well done! I've been a mechanic for 25 years and that's some quality work my friend. Keep them wrenches turning!!

Great video! I had to replace my gasket. I was trying to figure out why the case was so hard to take off. That's one strong magnet. Nipped my finger putting it back on .....ouch!!! Thanks brotha be safe out there.

bike wasn't charging battery, aka dead battery every 10min running. tested via ohms, DMM, rotor was giving less than manual specs. Bought new one, ran same ohm test, new one passed easily. mounted new stator. your video was invaluable!! i followed your route with the gears and the smaller back plate. The washer on the end, mine seamed either magnetic OR a good hole into the lining, not sure which. I was paranoid about dropping washer in, since the amount of effort to get cover off again, no thx. Went fine, i put smaller cover on and it meshed 1st try with the mounting holes. Felt good. Haven't started her up, need to get more oil first. I love the feeling of dissolving mystery. (didn't know what that stator part was until i was trouble shooting) i didn't think "what's that do?" but after having studied mechanical ect, now i know all parts. BUT knowing parts vs experience of working on them are different. Knowing about an alternator or stator is one thing.. crimping your fingers between 2 magnetic parts.. you learn. (thankfully i didn't, BUT had a close OCRAP.. as it did snap back on and caught me surprised.)

Love this video very first time changing my stator an everything turned out perfectly!

Thanks for the vid bro couldn’t have done it with out you

Great and detailed tutorial, thanks man, all the best !

great vid homie!!! thank you. im waiting on my rectifier from Ricks motorsports now... so im just going to replace the stator also. This video makes it seem easy enough for me to do it myself. Thanks again... new sub. ps. I also see that you relocated your rectifier to the side of your frame. Hows that going for you? I am going to do that too.

Going to be doing this to my next bike too. Thanks for the clear instructions Awesome video Subbed!

Thanks for the video!🤝

Such a good video..Thanks!

Thanks very helpful 👍

thank you so much for the help

Do you know the thread pitch I need to rethread one of the bolt holes the one at the top where the starter is

Do you only use thread locker for the stator bolts on the inside of the cover?

Wow man nice video you cut out the only hard part.

Thank you for that video very helpful

My starter cover is leaking oil. Have you ever seen that or fixed it? I just ordered an o ring for it hopefully that helps.

you make it look easy!

What if I put the last 2 washers in backwards. Thick one then the thin one last?

I did everything you showed in the video to replace my stator on my 08 gsxr 600 and my bike started up just fine and it runs smoothly but I have a slight concern. Is the the front end of my bike near where I just replaced the stator supposed to sound like a Yamaha R1M when it gets to the high rpm’s? It never did that before and it’s a little concerning

I tried using the link in your description for the cover but it links me to a weight

Hey man I bought my 07 gsxr 750 rebuilt title and the Stator actually went and swapped it out but when I pulled the starter cover off and carefully removed the washer that goes in first I noticed I was missing the last hard washer before you put the cap on. I guess the entire time owning it it’s been like that and I cannot for the life of me find dimensions on that last hard washer that goes in. I can’t find it anywhere online was just looking to see if you had any ideas !? Thanks.

I just did my second gasket why does it keep leaking. Do I need gasket sealer. I just don't get it.

i’m confused how many washer the start part need

I was crisscrossing the case too and it shattered

Hey I got a question for you..... when I took starter cover off the washer in that back that you said dont let it fall into engine....well it fell into engine. What is the easiest way to get it out ?

Nice man, much appreciated. What's the song you have playing at the beginning?

Nice guidd

What size washers are those because I’m missing the washers for it

How do I calibrate the bolt that regulates overflow oil breather ? I keep getting oil on my shoes and I already replaced the cover 3 times with level oil and new gadgets every time .

At 3:49 what happens if that washer falls into the engine? How far in does it go and how can you get it out?

In the piece that you put on the left side it has a screw I did not see that it was lazy or that you prepared it for what is it

Where did you get the stator cover? I'm having trouble finding a quality one without paying $250+ for an OE one

Isnt the factory gasket like a caulking material.

How can I know if the cover is OEM? It is necessary to use Maximum Oil Resistance RTV Silicone Gasket Maker

Do you have to torque any of the bolts at all?

Can someone help me find a video for the 2004s thank you!

I was changing mine, and the washer get inside the engine. How do i remove it?

You need to show the full process of taking the wires out now to replace the wires etc…u did a good job showing how to take the stator off nuts bolts etc…but a horrible job showing where the connectors go etc…horrible video

What if stator cover breaks a piece and goes inside . Will it damage any thing? At 40 50 kmph?