2009-2022 Ram 1500 Auxito LED 6000k Low Beam and High Beam Install

Подписаться 3,4 тыс.

Просмотров 23 тыс.

50% 1

We install Auxtio 6000k LED High and Low beam Light bulbs in my Dad's Ram 1500 Classic.
Check out the links below
Have any questions? let me know in the comments.
Don't Forget to use "thewiscoguyz" for 15% off your order.
Thanks for watching!
AUXITO WEBSITE- auxito.com/?ref=e6dmzabg2l
LOW BEAMS- auxito.com/collections/auxito...
HIGH BEAMS-auxito.com/collections/9005-l...
Canbus Adapter Anti-Flicker Warning Canceler for LED For 9005 and H11
auxito.com/collections/9005-l...
auxito.com/collections/auxito...

Авто/Мото

Опубликовано:

2 май 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 32

@crzypaiute 9 месяцев назад

A trick when removing push pins to avoid breaking or cracking them, use to go between the panel and vehicle, instead of under push pin. Then it pops free and also stays in place for easy replacement.

@daveremillard6257 Год назад

I was sold until seeing that the cover over the lamp would not fit. It sure seems like they would design something that actually was a direct fit without issues like covers not fitting.

@Kildahl1776 Год назад

I agree all these after market parts on websites. You tell them your exact model and mention 0 about flickering and a larger dust cover. If you manage to fit the cover you more than likely need to add the anti flicker which will for sure not allow you to close it. These headlights should be coming with anti flickers and extended dust covers for your model.

@JOSH-bx5wp 27 дней назад

You dont buy hemi for gas mileage. Great video bro. Thank you

@chemicals9820 Год назад

Excelente

@teagle148 9 месяцев назад

I am really hoping you can tell me where to find a bigger size dust cap for the headlight I have been looking and looking please 🙏

@matt73975 2 месяца назад

Buddy removes the grill for “easy access” to the lower bolt then proceeds to use enough extensions that he wouldn’t have had to remove the grill. And yes the grill does not need to be taken off, it very easy to get the lower bolt with the 4 miles of extensions like buddy in the video. Also, the high beam bulbs aren’t clocked properly. The diodes are at 12 and 6 not the correct position of 9 and 3

@alexmac666666 2 года назад

Finally somone properly describing the h11 being low beam(running lights) and 9006 being high beams. Was getting alot of mixed information on that. Also any check light bulb notifications or flickering ?

@TheWiscoGuyz 2 года назад

Yeah I got confused on some other videos too. No check light bulbs on the dash. They do flicker a little bit. But they do sell a resistor for that as well.

@alexmac666666 2 года назад

@@TheWiscoGuyz ok mint thank you

@michaelharrison988 Год назад

What resister do we get there are 2 options also I have fog light will I need a resistor for those as well?

@andyh9493 Год назад

@@TheWiscoGuyz what do you mean by flicker? Do you mean just when normally driving in low beam settings? Or when you turn on high beams?

@toyotabrony 6 месяцев назад

9005 is the high beams. 9006 is low beams as H11 as well.

@tedtwo Год назад

I just purchased lows and hi's and led fogs plug and play was Ganna do h I d but there just not the same and use twice the volts and burn hotter save a lot of money and now I'm over convenience that I'm going to like them in my o1 Duramax lb7 then all lights on mother board later

@josevasquez7784 6 месяцев назад

I would have used GTR lighting ultra 2

@DDalton59 Год назад

Did the led board line up at 3 and 9?i have auxito adjustable h11's,but they are too bright for street use and i want to replace them

@toyotabrony 6 месяцев назад

I am happy to hear that I knew I’m not the only to see those Q16 H11, that has a black Philip screw that’s hiding behind yellow grommet. Are they really adjustable? I’m sure 9005 is but what about those for H11? If u want less bright, switch to Auxito M3. That one is all in one metal piece. No screws Philips on them. We have them in 9005 high beams.

@Decountest Год назад

How did you aim them down a little so you're not blinding drivers in front of you

@TheWiscoGuyz Год назад

There are little holes under the hood on the top of the fender. You will see a arrow stamped in the fender that will point to a hole. In that hole is a adjuster for aiming your headlights

@Decountest Год назад

Thanks and keep up the great work

@TheWiscoGuyz Год назад

Thanks for watching

@Decountest Год назад

Did you end up having to use resisters for your dad's truck, i have the same model.

@TheWiscoGuyz Год назад

I did not

@Fueler 4 месяца назад

You don’t have to remove the grill to remove the headlights. And people please don’t install them headlights without dust caps.

@toyotabrony 6 месяцев назад

@TheWiscoGuyz Holy shit ur 9005 halogen bulb connector is aiming 9 o’clock. Putting on led will give u bad beam pattern and especially on high beams. Could u inspect again for ur 9005 high beams bulbs and see if u can mess around with that Philips screw, that’s blocked by the yellow O-ring. Loose that screw and see if u can rotate the orientation of the led bulbs? That one needs to face 3-9 o’clock as well for the best beam pattern as possible.