Wss= Wheel Speed Sensor ABS= Anti-lock Brake System it ended up being the wheel bearing Not responsible for anything you do with your property with this information.
My terrain 15 ,doesn't have a abs light but the wheel tire pressure light is on.i had to use a spare awhile back and don't have the wheel tool to relearn the tire pressure.
Check check all tires, spare included that the psi is correct if not add or subtract then it should go away by itself. If not one of the tpms or tire psi sensors are bad and will need replacement and possibly adaptation
Most of the times with my clients, they go bad due to tire change places damaging them when a tire swap is done and the shop doesn't saying anything because they didn't realize it or just ignored the damage done, then people realize to late that the tpms light stays on, or the go bad due to their internal, epoxied in batteries going bad
On my fifth month engine light turns and truck turns off after the brakes tightens before leaving car wash. I tried turning on but stabili trac and antilock brakes turned on. So after couple of attempts I got out and let it sit for 2 to 3 minutes. And tried again and it turned on. Maybe the soap and water was a bit too much for abs
Yeah i just need a good diagnostic computer. Is your bi directional or is it necessary? I have a 2010 gmc terrain. Stabiltrac popped on again after replacing spark plugs but now its off after restarting the car. Thank you.
If you want once you retrieve them text me here and I'll try to help you out with any more info I can give you ok?(If I could live stream i would do it twice a week to help you guys out so subscribe whenever you all can once I can live stream i can help out even more!)
Replaced the bearing it had a cracked abs ring magnet the works with the sensor and if the ring on bearing is cracked the sensor will send a erratic signal to abs computer
Hola tengo una gmc terrain 2010 que comenzo a fallar...se apaga y encuestion de segundos la prendo y se activa en el tablero stabilitrak service que puede estar pasando
Necesitas verificarlo con un scanner para confirmar que códigos tiene, en base a los códigos que salgan se supone que tengas mejor idea de que está sucediendo. Si no salen códigos, pon la llave en ON sin encenderlo(Osea no pongas la llave de modo que el starter encienda El motor) y presta atención cuidadosa a la parte de atrás en los asientos de los pasajeros a ver si hace sonido la bomba de gasolina, si no hace sonido puede estar mala, las bujías si están carbonizadas también te pueden causar este tipo de problemas bobinas malas también pueden estar en problemas..., hay múltiples áreas de rotura pero estas son las más comunes el scan tool te puede dar una mejor idea.
@@troubleshooterr5775 amimepaso amigo deir caminando imperdio la fuerza si prende icamina pero.seleva la fuerza i avienta mucho umo de abajo del mofle amigo que puede ser simepudieras Alluduar
@@LuisGonzalez-yd1py entre más detalles me des mejor la respuesta, que códigos tiene?, que color es el humo?, comienza a fallar cuando está parado o es cuando corre?
Buenas noches! Mi terrain 2012 acabo de empezar con esto se le prendió el stabilytrack y de repente después de una hora de uso la camioneta pierde potencia y no acelera, cuál podrá del el fallo ??
Disculpa, ya me la escanearon y era el sensor de velocidad del ABS de la llanta derecha de enfrente, pero al momento de cambiarlo por uno nuevo la camioneta da pero sin potencia no acelera, lo desconecto ese sensor y ya trabaja bien pero con los códigos prendidos del ABS del antiderrapante y del de frenos.. a qué se deberá o que se debe hacer ahí
@@josealfonsonavaquiroz5900 gira el volante completo hacia la derecha, trata de observar si puedes, la cinta magnética que el sensor monitorea. Este sensor que acabas de cambiar solo monitorea está cinta, esa cinta está conectada como una sola pieza con el balero(Wheel bearing). Por lo general esa cinta se estilla con pequeñas grietas, o simplemente te rompe en pedazos más grandes. Y como esta dañada el sensor te continúa dando problema. Verifica bien y me dejas saber
Esto fue lo que arreglo la troca m.ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-BDoVI2L-kjM.html&pp=ygUuMjAxMSBnbWMgdGVycmFpbiB3aGVlbCBiZWFyaW5nIHRyb3VibGVzaG9vdGVycg%3D%3D
Disculpa sigue dando el mismo problema, ya le cambié el sensor y sigue dando el mismo problema, que Cres que pueda ser ?? Tendrás algún número de WhatsApp para que me asesores
Scan the abs codes with a scan tool that reads ABS codes like I did on the video, Verify the data of the faulty area Replace faulty components. Review my channel in separate video you should have a good idea of how to fix your vehicle my friend
@@troubleshooterr5775 im being told that its the sensor that needs to be replace, however one guy already mentioned the bearings. which should be fixed?
When I dealt with this gmc it was the bearings not the sensors even though on the video I committed the error of calling out the sensors. Because the bearings have a flat magnetic ring in the back and it was broken. So the client still opted to change the sensors also at the time the bearing got replaced. So I'd recommend the bearing due to the fact that I've seen that the magnetic plate in the back of the bearing is weaker than the sensor construction wise.