Тёмный

2011 Toyota Camry Front Wheel Bearing Replacement 

Bullet Solano
Подписаться 40 тыс.
Просмотров 111 тыс.
50% 1

#BulletSolano #BalazoSolano #2011Camry #Toyota #LowerControlArm #WheelBearing #Axles #Studs
My Website www.bulletsolano.com/car-prob...
Torque Specs
Lug Nuts 80 FT-LBS
Brake Caliper Bolts 79 FT-LBS
Lower Ball Joint Nuts 94 FT-LBS
Lower Ball Joint Bolt 94 FT-LBS
Axle Nut 217 FT-LBS
Shock Strut to Front Axle Assembly Bolts 156 LB-FTS
Tie Road End 36 FT-LBS
Gratitude www.paypal.me/bullet23
• How To Replace Front W... Wheel Bearing Video on my Accord
amzn.to/3iWNrSR Front Wheel Drive Bearing Puller Press Replacement Installer Removal Tool Kit
amzn.to/32albWb 30MM Deep Socket 12-Point
amzn.to/2YiURrS 1 1/4 Socket
amzn.to/3iWNcHr 1 1/8 Socket
This is the tool set I always used for my videos
amzn.to/2CSEv1k Craftsman 320 piece Mechanic Tool Set
amzn.to/38gsyxR Gearwrench Breaker Bar
amzn.to/2ZpmPSv Bolt and Nut Remover Sockets
amzn.to/3eykVFk
Duromax XP2700PWS 2.3 GPM 5 HP Gas Engine Pressure Washer, 2700 PSI
amzn.to/2NEYRxj Foam Canon
amzn.to/31eKBTV Chemical Guys Gloss Booster Shampoo
amzn.to/2Cy9zTK Chemical Guys Heavy Duty Detailing Buckets
amzn.to/31g7RB0 Chemical Guys Dirt Trap Car Wash Bucket Insert
amzn.to/319JZyO Chemical Guys Chenille Premium Scratch Free Microfiber Wash Mitt
Hi Guys and welcome to another episode
if you have any questions please let as know
Thanks for watching and don't forget to Subscribe.
--------------------------------------------------FOLLOW ME---------------------------------------------------
Follow me on Instagram
@bulletsolano36
Follow me on Twitter
@bulletsolano
Like my Facebook page
/ luis.b.solano.3
Thanks for watching.
Disclaimer.
This video contains tips and recommendations only.
Bullet Solano Shall not be liable for any harm, injury damage or if anything bad happens to your vehicle or property got in the process of repair and replacement due to use or misinterpretation of the information on this video.
Keep in mind that if you buy low quality auto parts does not guarantee the adequate level of road safety.

Авто/Мото

Опубликовано:

 

19 авг 2020

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 141   
@fredguerra4917
@fredguerra4917 3 месяца назад
Carnalito, Than you for taking the time to show the way you doit. Excellent! I have a 12 ton bench press but sometimes is a pain in the rear because of the shape of the knuckle. Your method is easy much more practical and the tools take less room. Thanks again with respeto to your skills.
@BulletSolano
@BulletSolano 3 месяца назад
My pleasure bro
@jerrydc818
@jerrydc818 2 года назад
Reminded me on how people fix things in the Philippines. No need for fancy hydraulic press. Bravo. Thx for posting
@Jahalang82
@Jahalang82 2 года назад
I've got a 15 AWD Honda CRV and this video is probably the closest setup I've seen yet on youtube. That's awesome that you did it basically on the ground without using a bench vice because I dont have one either and now i know that it's possible to replace front pressed in bearings without needing a press.
@mikegonzalez6661
@mikegonzalez6661 Год назад
Excellent video for those that want to be mechanics without all the super fancy tools! Gonna use these instructions this week-end, keep you posted!
@BulletSolano
@BulletSolano Год назад
Thanks
@michaelhartzell9758
@michaelhartzell9758 3 года назад
Very good video. Makes me believe a regular person can replace one without a tire shop doing the work. 😉
@BulletSolano
@BulletSolano 3 года назад
Thanks
@sveltland
@sveltland Год назад
Thanks man! You got me threw one bearing.. Now doing the other side. Great video.
@johngoudie6676
@johngoudie6676 2 года назад
Thank you so much for this video, I have my bearings to do and this really helps!😊👍
@javierreinis7908
@javierreinis7908 3 года назад
Excellent video, very easy to understand, I’m gonna replace both bearings in my Camry with just your instructions!! Thank you
@BulletSolano
@BulletSolano 3 года назад
Thanks
@carlosortiz8843
@carlosortiz8843 2 года назад
@@BulletSolano >u I
@billsmith-cr6dt
@billsmith-cr6dt 11 месяцев назад
Thank u. Just redid my Camry. Your video was great and I bought the same tools you have to do it
@garylcarrier
@garylcarrier 2 года назад
Excellent video presentation! Thank you!
@sta39cee
@sta39cee Год назад
Excellent video. Very well done and explained. Thanks.
@spartapower4863
@spartapower4863 Год назад
Amazing video thanks for your explanation of the procedures
@docvince888
@docvince888 3 года назад
you made it look easy my friend!!! great job!!!
@BulletSolano
@BulletSolano 3 года назад
Thanks
@mark80621
@mark80621 2 года назад
thanks man! great content
@user-nz6cm1yw7u
@user-nz6cm1yw7u 11 месяцев назад
Excellent video, only issue is when I worked at mechanics shop we were instructed to lubricant bearings and press ins great video
@jorgevega238
@jorgevega238 Год назад
Great job. I have the same car. This will definitely help me. Thanks
@big_turk
@big_turk Год назад
Great video sir, thank you!
@majorphenom1
@majorphenom1 Месяц назад
Thanks for sharing 🙏🏾
@RossMKF1
@RossMKF1 3 года назад
Great vid man! Thanks for the help!
@BulletSolano
@BulletSolano 3 года назад
Thank you
@freddyescamilla1736
@freddyescamilla1736 7 месяцев назад
Very good video excellent!
@teddiazjr.6223
@teddiazjr.6223 Год назад
Great video and details
@elibaez4092
@elibaez4092 2 года назад
Thanx bro ! You video was super helpful I was able to do Both side on my Camry
@BulletSolano
@BulletSolano 2 года назад
No problem
@andyrodriguez7186
@andyrodriguez7186 3 года назад
Thanks for the excellent job.
@BulletSolano
@BulletSolano 3 года назад
Thanks for watching
@16dbuse
@16dbuse 3 года назад
Great video, thank you.
@BulletSolano
@BulletSolano 3 года назад
No problem
@mendezavala4817
@mendezavala4817 Год назад
Good job
@rafaeldeleon225
@rafaeldeleon225 10 месяцев назад
Straight forward Bro.
@TigerKittay
@TigerKittay 3 года назад
Pretty good! I have the same wheel bearing kit.
@BulletSolano
@BulletSolano 3 года назад
Nice
@travisegnor2417
@travisegnor2417 2 года назад
Thank you sir.
@rsmeali747
@rsmeali747 Год назад
Thanks a looot!
@wilsonparker9796
@wilsonparker9796 3 года назад
thank you for the video
@BulletSolano
@BulletSolano 3 года назад
No problem
@tommason5689
@tommason5689 Год назад
Guys, never put the retainer ring until hub is fully installed. Otherwise, you can ruin the bearing because the tool bushing does not come in contact flush with the bearing due to the thickness of retainer ring while installing the hub. This causes the inner race of the bearing to be pushed out as much as the thickness of the retainer ring. I made the mistake of installing the retainer ring right after the bearing was pressed in but before the hub was installed. And I wasted a bearing and had to start all over again which was a big bummer. Do not make the same mistake I made.
@joeylawell3590
@joeylawell3590 Год назад
Thx bro
@cleiltonalmeida5682
@cleiltonalmeida5682 2 года назад
Great video
@BulletSolano
@BulletSolano 2 года назад
Thanks
@dannysautorepair
@dannysautorepair 3 года назад
Great job sir.
@BulletSolano
@BulletSolano 3 года назад
Thanks
@geecrawdad
@geecrawdad 3 года назад
Nice. Well done.
@BulletSolano
@BulletSolano 3 года назад
Thanks
@JAI45624
@JAI45624 3 года назад
Nice job
@BulletSolano
@BulletSolano 3 года назад
Thanks
@ammaralamdar9444
@ammaralamdar9444 3 года назад
Thank you
@BulletSolano
@BulletSolano 3 года назад
No problem
@peshpraq5137
@peshpraq5137 2 года назад
Very nicely done Many thanks for the upload I have an avensis deisel 2012 , I was wondering how similar they are. I bought the front hub and bearing already assembled how you install that?
@BulletSolano
@BulletSolano 2 года назад
If your bearing is already one piece you have to remove the axle nut and probably 3 or 4 bolts from the back to remove the bearing assembly
@torresmobilecarwashandauto201
@torresmobilecarwashandauto201 3 года назад
Gm get it done
@nelsonsreach2785
@nelsonsreach2785 Год назад
The notch at the end of retaining clip was broken off on mine. I drilled into the clip with a 1/8" bit (go slow and use lots of oil, and be careful not to go all the way through, then you can jam a punch into the hole and pry the clip out.
@2002erli
@2002erli Год назад
H O T V I D E O ! ! ! - Thank you!
@nordicpride9708
@nordicpride9708 Год назад
Great video. Next time I’d recommend using NSK or KOYO bearings on a Toyota. Duralast are pretty low end
@BulletSolano
@BulletSolano Год назад
Customer’s car, he get the parts I put them on! I know autozone sucks
@nordicpride9708
@nordicpride9708 Год назад
@@BulletSolano Yeah I get that. I have customers bring me all sorts of stuff haha. Appreciate the link to the bearing removal kit. The one I have isn’t very useful for Toyota/Lexus, so I typically use a buddies press. This method is much easier 🤙🏻
@carberros-7298
@carberros-7298 2 года назад
Good video man! What size bolt do you use to remove brake disk? Thanks much!
@BulletSolano
@BulletSolano 2 года назад
12mm
@rogeryanez8107
@rogeryanez8107 2 года назад
Good video brother, I'm currently doing the same job however I can get the top strut bolts to align it seems like there's some tension causing it not the align, any tips I can do to have everything align. Thanks brother and greetings from Los Angeles ✌
@BulletSolano
@BulletSolano 2 года назад
You have to pull and push the strut assembly and put a pry-bar inside the hole to get it align
@jayceestennis3538
@jayceestennis3538 3 года назад
How long was the entire process for you from start to finish. not the video time stamp... great video mi amigo!
@BulletSolano
@BulletSolano 3 года назад
Thanks, with out recording is about two hours
@JavierMartinez-vx1dp
@JavierMartinez-vx1dp 10 месяцев назад
👍
@kednielramirez8978
@kednielramirez8978 2 года назад
Thanks sir you save me $2500 in fireston
@silviaorriols8532
@silviaorriols8532 Год назад
I just wonder how tie I have to do the Axle nut everything I can do it but that nut is my only worry if I leave or lose or to tied.
@BulletSolano
@BulletSolano Год назад
217 lb ft
@tommason5689
@tommason5689 Год назад
One more question, Bullet: Did you have to do wheel alignment after the job? I guess it is good thing to do anyway but was wondering if the wheel alignment went out of whack after taking the whole thing off and putting it back on. Thanks again.
@BulletSolano
@BulletSolano Год назад
Customer’s car, I think he did the alignment But yes you have to do it
@Outrunninaround.
@Outrunninaround. 2 года назад
Make sure what side of the bearing is towards the inside. It matters for the wheel speed sensors.
@christophershanklin112
@christophershanklin112 7 месяцев назад
lol he said that at the beginning
@Outrunninaround.
@Outrunninaround. 7 месяцев назад
@@christophershanklin112 damn! That was a year ago?
@rmf11699
@rmf11699 2 года назад
QUESTION: my Camry has over 200k miles on it do you recommend replacing the hubs or can I get by with just bearing replacement?
@BulletSolano
@BulletSolano 2 года назад
It all depends on how bad the hubs are, probably it will be a good idea to replace them
@LuisPinedaily
@LuisPinedaily 3 года назад
Did the axle nut spin in freely? I changed out my bearings and hub and find that the new axle nut does not spin in freely although it does fit. I’m just wondering if it’s meant to be a very tight fit so it doesn’t spin back out. I’ve heard that they’re a one time use.
@BulletSolano
@BulletSolano 3 года назад
Yes they’re one time use
@Loulito
@Loulito 2 года назад
You must live in the West Coast, LOL. Try doing this on a New York camry haha you're gonna need power tools or a hydraulic press. Nice work though :)
@BulletSolano
@BulletSolano 2 года назад
I live in Georgia, that’s the reason I don’t like up north, I have family in Indiana and every time I go there I work on cars with my brother in law, is crazy how he do that every day
@Loulito
@Loulito 2 года назад
@@BulletSolano yea man it’s no joke. I wish I lived out there. When I saw you bang out the bearing with the hammer I laughed (then started to cry) haha. I’m like man it MUST BE NICE! I have the beefy Milwaukee 1/2 and 2 3/8 impacts to get the job done. They have saved my ass but still some jobs are still ridiculously difficult. I use torch’s and all that to get stuff done.
@BulletSolano
@BulletSolano 2 года назад
Crazy man
@babakkk100
@babakkk100 Год назад
excellent job. Please let me know what brand you used? where did you buy it. I have camry 2013 le model. not sure where to buy and what brand? thanks
@BulletSolano
@BulletSolano Год назад
Customer get them at advance auto parts
@babakkk100
@babakkk100 Год назад
@@BulletSolano what brand? the one you used in your video is 1A auto brand?
@BulletSolano
@BulletSolano Год назад
Long time ago, I’m not sure what bearing are those, check in advance or Napa
@WutsParanormal
@WutsParanormal 3 года назад
How do you remove the hub with the dented in nut? I used a punch tool but it broke, also, when I tried using a breaker bar to break off the nut, it broke the breaker bar.
@BulletSolano
@BulletSolano 3 года назад
You saw the video, get another punch tool, and bigger breaker bar
@melissaadame4001
@melissaadame4001 3 года назад
Where you get that bearing removal kit and what brand is it? Cool video btw
@BulletSolano
@BulletSolano 3 года назад
The link is in the description
@TigerKittay
@TigerKittay 3 года назад
I bought mine from Amazon for about $86.
@diegopalomino1200
@diegopalomino1200 3 года назад
You can borrow one of those from Autozone or any other major auto parts stores. They ask for a deposit and when you bring it back they give your money back.
@marvinkanhai3808
@marvinkanhai3808 Год назад
Which side the duralst bearing goes for the abs
@BulletSolano
@BulletSolano Год назад
Doesn’t matter, abs is not reading on the bearing is reading on the axle
@tommason5689
@tommason5689 Год назад
If you want to use the old hub, what is the good way to cut the remnant of the bearing stuck on the hub to get it off?
@BulletSolano
@BulletSolano Год назад
Dremel or angle grinder
@tommason5689
@tommason5689 Год назад
@@BulletSolano Thanks for reply!
@adnerflores2827
@adnerflores2827 2 года назад
Bullet buen video una pregunta tengo un camry toyota le 2014 le boy a remplazar el wheel bearing lleva alguna posición la instalación....y la otra pregunta lo compre en autozone el bearing en 50dolares que tan bueno será en esa tienda????
@BulletSolano
@BulletSolano 2 года назад
Qué tal, ponle un clavo o algo de metal por los lados, si tiene iman en alguno de los dos lados el lado con iman va hacia dentro donde va el sensor de velocidad pero no creo que tenga iman por lo cual lo puedes poner del lado que sea, y nunca he tenido problemas con los baleros de ellos
@adnerflores2827
@adnerflores2827 2 года назад
@@BulletSolano muchas gracias porque fíjate que hice la muestra como me dijiste con un clavo para ver si tiene imán 🧲 el balero pero ningún lugar lo tiene....lo puedo instalar así entonces crees que no perjudique el sensor de velocidad en nada????
@BulletSolano
@BulletSolano 2 года назад
Instalalo de cualquier lado
@adnerflores2827
@adnerflores2827 2 года назад
@@BulletSolano muchas gracias mañana mismo lo haré estaba esperando la luz verde de tu parte para hacer el trabajo......primero Dios que no prenda el sensor de velocidad en el tablero SALUDOS DESDE DALLAS TEXAS
@BulletSolano
@BulletSolano 2 года назад
Saludos
@ask43242flight
@ask43242flight 2 года назад
What is the bearing removal tool you used? Thanks
@BulletSolano
@BulletSolano 2 года назад
Link in the description
@shaewinston
@shaewinston 2 года назад
I am doing this job on the same 2011 Camry.. Which way does the wheel bearing go in does it have a magnet I can't tell with my new bearing.
@BulletSolano
@BulletSolano 2 года назад
Put a metal clip on both sides to see if it is magnetic
@shaewinston
@shaewinston 2 года назад
@@BulletSolano I did it falls off both sides ..does it mean it doesn't matter? But the abs sensor drops in front of the ring when installed 😵‍💫
@BulletSolano
@BulletSolano 2 года назад
It doesn’t matter
@edwinsantiago116
@edwinsantiago116 Год назад
SOLANO donde puedo comprar ese set de puller ? 🤔
@BulletSolano
@BulletSolano Год назад
Enlace en la descripción
@marvinkanhai3808
@marvinkanhai3808 Год назад
Harborfrieght
@tommason5689
@tommason5689 Год назад
Is there no way to remove the hub using the tool you have instead of hammering?
@BulletSolano
@BulletSolano Год назад
What? You asking if I can remove the hub with the tool????
@tommason5689
@tommason5689 Год назад
@@BulletSolano Your answer says: No. Thanks
@xaysaysombath6453
@xaysaysombath6453 3 года назад
Hello Sir, i have a 2011 toyota avalon with V6 3.5 liter evrything will be the same as this video Right?
@BulletSolano
@BulletSolano 3 года назад
Yes, is the same
@xaysaysombath6453
@xaysaysombath6453 3 года назад
@@BulletSolano Where can you buy the tool that remove bearing?
@BulletSolano
@BulletSolano 3 года назад
amzn.to/3kaXJTc
@2002erli
@2002erli Год назад
This is a K I C K - A S S V I D E O - T hank you ! ! !
@freddyescamilla1736
@freddyescamilla1736 7 месяцев назад
How do you call the tools for that?
@BulletSolano
@BulletSolano 7 месяцев назад
amzn.to/3RcjX7B
@dvader3000
@dvader3000 2 года назад
you make it look easy. I noticed you didnt apply any grease. they come already pre greased?
@BulletSolano
@BulletSolano 2 года назад
This bearings are sealed no grease need it
@inasingtr
@inasingtr 3 года назад
6:43 baseball player.
@julieannbrown5843
@julieannbrown5843 2 года назад
Well done i wish you are close to me to get mine done please
@BulletSolano
@BulletSolano 2 года назад
Thanks, Atlanta GA
@julieannbrown5843
@julieannbrown5843 2 года назад
oh i’m in Florida but i use your video and order the parts so i’m going to continue with my brother to get it fix .Your video is straight to the point
@jorangel87
@jorangel87 2 года назад
Why not just buy the whole knuckle assembly for $200 and replace it in half the time with removing the bearing.
@BulletSolano
@BulletSolano 2 года назад
You do that, I’ll do this
@BulletSolano
@BulletSolano 2 года назад
Not all my clients have the money you do
@lvsurfcat8584
@lvsurfcat8584 2 года назад
Wow,$200. really, is it good quality? Pls. Tell me where to buy
@qax9037
@qax9037 2 года назад
u damaged the abs magnetic ring
@BulletSolano
@BulletSolano 2 года назад
I don’t think so
@rudycap27
@rudycap27 2 года назад
How did he damaged it?
@trahuynh_usa
@trahuynh_usa 8 месяцев назад
I wanted to see last part when you put the hub back on axel you cut it out
@locotx215
@locotx215 2 года назад
Uh that looks like a Toyota Sienna
@mahmoudrezajamshidi6030
@mahmoudrezajamshidi6030 2 года назад
Good job
Далее
How to Replace Wheel Bearing & Hub 04-16 Toyota Camry
35:16
How to Replace a Front Wheel Bearing
16:26
Просмотров 9 млн
2020 toyota camry wheel bearing replacement
14:13
Просмотров 1,1 тыс.
Toyota Corolla: Front Wheel Bearing Replacement
29:53
Просмотров 699 тыс.
How to Replace Wheel Bearing 2012-2017 Toyota Camry
29:00
Most Common Brake Installation Mistakes!
13:29
Просмотров 4,3 млн
Тест Подвески БМВ
1:00
Просмотров 301 тыс.
впихнул турбину в глушитель
1:00