2019 Toyota Rav4 How to install Curt 56434 Custom Wiring Harness

Подписаться 5 тыс.

Просмотров 13 тыс.

50% 1

In this video i will show you how to install Custom Wiring Harness Curt model #56434 2019 Toyota Rav4. If you are planning to tow anything with your Rav4,than this video is for you. I recently purchased 4x8 trailer for my kayak,and I needed to install this wiring harness so could tow.
You can find this curt wiring here
www.amazon.com/CURT-56434-Veh...
Link to hitch installation video
• 2019 Toyota Rav4 hitch...
If you have any question or if you would like me to review your products,please contact me at
Nazarettos@gmail.com
You can also buy me a coffee ☕ if you like the content.
www.paypal.com/cgi-bin/webscr...
DISCLAIMER: All information displayed in the video is for entertainment and informational purposes only. You can't treat it as professional advise. Should you decide to act upon any information in this video, you do so at your own risk.

Спорт

Опубликовано:

20 июл 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 22

@allenbosely2059 Год назад

Thanks for this video! Was very helpful. You went slow enough that could follow but not too slow. Was easy to see what was being done as you went.

@nazarettos6987 Год назад

Thank you for positive comments. I am still using it. This harness works perfectly fine after two years. One thing I would recommend for you, if you are not using the harness for towing disconnect, the fuse. Because when you have a constant power the end will start oxidizing and you will have to clean connector.

@smartphonerepairwi775 Год назад

Very informative step by step video! Hardest part is definitely routing underneath the vehicle. This worked on my Jeep.

@raysharplessjr 3 года назад

Great video. Doing the install for myself and this was very helpful as the included directions are black and white and very hard to follow for someone new to this type of install. Thank you

@nazarettos6987 3 года назад

Thank you for positive feedback. I'm still using my trailer and this harness worked well.

@Samactinhiu 3 года назад

on the 18.45 minutes, you don't have to cut the black rubber cap. just make a hole and put the electric line through it.

@yanghagen1495 3 года назад

Great video, thanks a lot.

@nazarettos6987 3 года назад

Thanks for positive comments

@yanghagen1495 3 года назад

Nazarettos of course, it’s not only a helpful video but also everyone need to show respect and gratitude to your diligent effort. No reason to be picky or leave without a comment.

@grahamdougherty226 3 года назад

Thanks boss!

@nazarettos6987 3 года назад

You welcome,hopefully this,video helped.

@newamsterdanm День назад

Thank u Boss, what a well done detailed video🫡, very appreciated 8:51

@nazarettos6987 День назад

@@newamsterdanm thank you for such a beautiful comments

@albertotanikawa4762 Год назад

Thanks for making this video. On either side, above the connector where you connected the T-harness for the blinkers… are those wires for the reverse lights? If so, that would make tapping into reverse signal so much easier than routing all the way up the trunk lid.

@nazarettos6987 Год назад

I did not wanted to cut any wires, it was just easier this way to plug and play. Also what I do is when I am not using trailer, I disconnect fuse directly under the hood, this way there is no constant power going trough that cable. I notices some people have corrosion of connector.

@crazy-es8tr 4 года назад

When you were connecting the wires to the battery you are not supposed to clamp them you are supposed to use a lighter on it so It can shrink because now water can get on and make it all corroded

@nazarettos6987 4 года назад

I'm gonna tape it and its under the hood of the car. I'm also gonna buy wrap around heat shrinking tape.

@joshuasortland2028 3 года назад

Why cant you use an existing hot wire. Why do you need to run a wire to the battery?

@nazarettos6987 3 года назад

Hot wire is for the power. I could technically connect it to power wire from lights or some other source,but you don't want to overload the system. That's why you have to run power directly from the battery positive terminal with fuse in the line.

@richardhaase3064 Год назад

Tap into the 12 volt power outlet on pass side just use inline fuse holder , instead of running wire all the way to front of vehicle, do this all the time , no problems