Zdemontuj i zamontuj oponę, bez zdejmowania koła z ciężarówki! I to wszystko w kilka minut! Firma Eurogold jest wyłącznym dystrybutorem systemu Tire Spyder w Polsce.
As a person that has worked in the tool industry for close to 15 years and now run my own equipment business. The one thing I have to say is "Speed isn't always your friend" in this industry especially on the commercial side. The one thing I have a problem with is that tires should always be inflated in a safety cage, new or used! I know it is the one rule that is ignored more times than not and it shouldn't be! Look up a few tire explosion videos, when you have 100+PSI in a tire and it lets go (and it can happen) bad things happen when it does! My number one rule in business is that I just want everybody to go home at the end of the day! Have a good day and stay safe to all who read this!
So, you air it up in the safety cage to required pressure. Now you have to roll it to the unit and get right down beside it to wiggle it on the hub. Ever have one blow then? Put it on the unit with 10 psi, bolt it down then air it up with an extension line with a regulator from a distance. Just sayin'
It’s about time technology follows truck tire service, but doing this work for over 20+ years, I could of takin it off by the time that thing is out of the truck. Drivers appreciate the quick service after waiting hrs on the road waiting for there dispatch to get some one out to them.
Witam. Moje pytanie: co z kołem wewnętrznym na bliźniaku/napędzie? bo pomysł jest świetny jeśli chodzi o koła skrajne a wewnętrzne ? Wtedy żeby taka oponę ściągnąć trzeba by odkręcić zewnętrzną tak?
Najlepiej zdjąć zewnętrzne koło (dlatego w naszym mobilnym serwisie TORQ - zapraszam do obejrzenia innych naszych filmów - posiadamy klucz pneumatyczny 4300 nM) wewnętrzne przykręcić tymczasowo w jego miejsce, dokonać zmiany opony i założyć koła na ich pierwotne pozycje. Jest mozliwość wykonania procedury, gdy koło leży na ziemii, a le z naszego doświadczenia wynika, że opcja pierwsza jest wygodniejsza.
Ponieważ pojawiąją się komentarze odnośnie odbijania opony - informujemy, że jest to skrócona wersja filmu instruktażowego, którego pełna wersja znajduje się na profilu TORQ Mobile Tire Service.
Hi EuroGold, the 3 minuty z Tire Spyder is great tool. Kindly direct me on where to purchase one and to ship it to my country Kenya. i have a shop here and it would be very handy here. My email address is (waiganjoeric@gmail.com)
***That is super cool please don't think I'm hating but when it comes to Big Truck safety you have to treat them better than your car meaning you never put a brand new tire on your dirty car rim same thing applies to a big truck or 18 wheeler or anything for that matter just take the time clean the bead of the room on the inside just so that the new tire seats against only the rim have a blessed day my friend very 😎!***
jak ktoś z kolami w dużym aucie nie miał do czynienia to zapewne nie wie ze oponę to 2 łyżki i po robocie a żeby założyć to klucz hiszpan lub jakiś zaciskowy
This is cool and definitely easy on the body but it definitely takes too long i can change an outside tire in under three minutes including jacking it up
I about croaked watching that. I'd put 5Gs of my own money up and say I could do two tires manually faster than that little tool. I also would argue that you're physically touching the tire more than I ever have doing it with a "Go" bar. There is a video of an one armed man overseas that does tire job on a mounted wheel and tire chage and I believe he does it in under 2 minutes.
Good tool if the customer have all day to change his tire . Plus the hard part of changing an outside tire it's braking the inside bead more if it's a chinesse brand
Soooooo you want me to spend a tremendous amount of money on this thing so I can change tires slower than I currently can with a tire iron, a duck billed sledge hammer and a bucket of slick-em. This is only impressive to people who have never changed a tire on a tractor trailer.
My tire guy would of almost finished the entire axle by the time you set this junk up get your little bars on and the safety pin hed be drinking a tecate and be ready for the next axle
I just saw another video and that guy did it way faster and with no advance tools just muscle, knees and bars. Took 1 min and second by the time this set up his equipment.