Тёмный
No video :(

350z Knock Sensor and Harness Replacement 

Reubs Modification's
Подписаться 5 тыс.
Просмотров 10 тыс.
50% 1

How to replace the knock sensor and harness on your VQ35DE. My tuner let me know that my car was sending a knock code consistently but were able to tune around the code. Although the car was running fine it was best to replace the sensor as the engine had no protection from knock. This was not overly difficult but did require a couple hours to complete with basic tools.
Throttle Reset - • Idle Relearn - FX35, I...
Rat Proof Harness - www.amazon.com...
Knock Sensor - www.sparesbox....
Music ~ "Galaxzy" - Lost via SJM Media

Опубликовано:

 

22 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 23   
@stealthg35infiniti94
@stealthg35infiniti94 Год назад
Tip: Disconnect the Fuel rail in the back flange, this way you can take out the fuel rail and lower plenum together. This will minimize the chances of your injector Orings from leaking unless you have installed new ones.
@ReubsModifications
@ReubsModifications Год назад
That's a great tip, always good to minimise the chance of damage especially with rubber seals 👍
@ceironedwards7646
@ceironedwards7646 8 месяцев назад
Alright mate! What symptoms did you have with the bad sensor/harness? Was it just the fault code or was it running rough
@ReubsModifications
@ReubsModifications 7 месяцев назад
From what I could remember there was only the fault code, however when I went to get it tuned they couldn't do anything with the fault there so it had to be fixed.
@6545jake
@6545jake Год назад
Lol great video bro, keep inspiring us 🦾
@ReubsModifications
@ReubsModifications Год назад
Thanks mate 🤙🏻
@igorngandjui2763
@igorngandjui2763 2 года назад
How where you able to get your hand behind the engine to disconnect the harness?
@ReubsModifications
@ReubsModifications 2 года назад
Small hands 👍🏻
@edwardgarcia564
@edwardgarcia564 Год назад
Could a faulty knock sensor or harness cause a misfire.
@ReubsModifications
@ReubsModifications Год назад
Yes could be the cause
@poseidon4979
@poseidon4979 Год назад
Does anyone know if theres a specific torque when putting everything back
@DAVORIMAGE
@DAVORIMAGE Год назад
Yes, must torque it to spec to avoid any type of leak.
@manuelm2999
@manuelm2999 2 года назад
how long did it take you?
@ReubsModifications
@ReubsModifications 2 года назад
Id say 2ish hours to take everything off and 3 to put everything back on
@edlastimosa5872
@edlastimosa5872 Год назад
how is the harness doing , Saw a bad review only lasting 1 year
@ReubsModifications
@ReubsModifications Год назад
No signs of it failing yet
@alvinrodriguez1480
@alvinrodriguez1480 11 месяцев назад
How is it holding up now?
@edlastimosa5872
@edlastimosa5872 11 месяцев назад
@@alvinrodriguez1480 mines doing pretty well, i feel like replacing it definetly gave my car more throttle response.
@Atheos125
@Atheos125 Год назад
Didn’t show connecting it in the back
@ReubsModifications
@ReubsModifications Год назад
Sorry mate was a bit tricky to get the camera in there
@adrian619lozano
@adrian619lozano 2 года назад
What code was your car throwing ? I'm having the same problem with code p0328. Thanks
@ReubsModifications
@ReubsModifications 2 года назад
Hey mate, I didnt know the code it was coming up with, when my car was tuned they let me know that the knock sensor had failed.
@Jtsn0w
@Jtsn0w 2 года назад
p0328 is the knock sensor from what ive learned po327 is the harness
Далее
My Nissan 350Z Gets The Complete Service Overhaul
11:07
How to Install a 350Z/G35 Knock Sensor & Harness
20:25
Vq35de G35/350Z knock Sensor replacement.
11:16
Просмотров 80 тыс.
VQ35DE Intake/Plenum Port
14:06
Просмотров 15 тыс.
300 WHP 350z DE
6:17
Просмотров 1,1 тыс.