5 Channel Amplifier Installation (JL Audio XD 700/5) | AnthonyJ350

Подписаться 119 тыс.

Просмотров 138 тыс.

50% 1

In this video I go over the essentials when installing a 5 channel amplifier.
#5Channel #Amplifier #SoundSystem
Subscribe for more automative tips!: bit.ly/sub2anth...
Watch my most popular uploads!: bit.ly/anthonyJ...
Website: gofasthavefun.ca
Instagram: / anthonyj350
Twitter: / anthonyj350
Facebook: / aj350
Shop: www.amazon.com...
Music available - www.jinglepunks... & www.epidemicsou...
About AnthonyJ350
I am a Mobile Electronics Certified Professional 12 Volt Installer (MECP Certified), Business Management Graduate (KPU), with a Professional Driver's License and a genuine automotive enthusiast who loves working on vehicles and I want to share my experiences with you. The goal is to help other people who can hopefully learn from my unique outlook towards vehicles, experiences and working practices.
Please feel free to ask questions or give feedback either in the comments or e-mail me.
New videos every week.
Please check out official web site (www.gofasthavef...) for our disclaimer as we are not professional mechanics but experienced automotive enthusiasts sharing our experiences and providing entertainment content.
Go Fast Have Fun provides the content in this video, for information and entertainment purposes only.
The information in this Video presents guidelines to help vehicle enthusiasts modify or repair their vehicles and to demonstrate what car culture is all about. Go Fast Have Fun make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the Video or the information, products, services, or related graphics contained on the Video for any purpose. Any reliance you place on such information is therefore strictly at your own risk. Nothing presented should be relied upon you for your modification or repair plans for your vehicle and is not in any way professional mechanical advice.
Go Fast Have Fun strongly recommends you consult with a professional automobile mechanic to ensure that any modification or repair plans for your vehicle are appropriate for your vehicle.
In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arising out of, or in connection with, the use of this Video and the information presented within it.
Go Fast have Fun
Canada
5 Channel Amplifier Installation (JL Audio XD 700/5) | AnthonyJ350
• 5 Channel Amplifier In...
ANTHONYJ350
/ anthonyj350

Опубликовано:

15 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 115

@saskueify 8 лет назад

thanks for making a video that no-one can see

@AnthonyJ350 8 лет назад

+Diamond Louis XIV You can donate some money so I can invest it in lighting. Because talk is cheap. Sorry for the free information that I take the time to make for people like you, to have just complain for no good reason. But I'll keep trying.

@saskueify 8 лет назад

AnthonyJ350 It's called a flashlight idiot, stop asking for handouts. I came here for a burger and you gave me an inedible piece of shit. I don't feel bad for you

@AnthonyJ350 8 лет назад

+Diamond Louis XIV Well I can't turn back time, but if you look at my newer videos there's more lighting. It's funny how you can be so critical of my stuff when most of your videos have black bars on the side because you're holding your phone the wrong way for video. But at least you post videos compared to most trolls. And the quality is what I expect.

@saskueify 8 лет назад

AnthonyJ350 I'm not even a serious RU-vidr. I post for shits and giggles not to relay serious info. All you had to fucking do is tell me what plugs into what and where but you just pointed at a black cavern that I assume was your engine...Just saying...your wasting your own time and mine by making bad vids

@AnthonyJ350 8 лет назад

Diamond Louis XIV Well know this. Instead of giving constructive criticism you come off as a self entitled little s***. I have corrected this issue over the past year. And not everyone is perfect, so yes my earlier videos aren't the greatest. But it's ok I make enough $$$ which reflect my improvements. Don't expect someone like me to help out someone like you that comments with that much disrespect.

@philiphan6997 Год назад

I know this is an old thread. I'm using this same amp with a stock honda head unit with separate tweeter and woofer leads. How do I get both leads into the amp? Do i just combined them and RCA them to the amp? Will this damage the head unit?

@AnthonyJ350 Год назад

You'll need to install some sort of passive cross over. Like a cap on the positive line of the tweeter or a passive cross over from an aftermarket speaker. Or delete the rear speakers. Put the tweeters on the front channel of the amp and the woofers on the rear and cross them over at the amplifier.

@ekong85 9 лет назад

Do I have to plug another set up RCA cables from my 5 channel amp to the HU separately, for my subwoofer? I will bridge 4 of the channels to power a pair of 2 way component speakers for the front (massive ck6). Im using the last channel to install a subwoofer. Currently I have a set of RCA cables plugged into my HU's front speaker output, to my amplifier.

@paulgeorge9614 9 лет назад

Hey im looking to add a center speaker to my car audio system i have a center dash grill with no speaker in it i have a aftermarket 4channel head unit and im also running a 2 channel bridged 600w amp off my subwoofer pre amp rca my question is how would i go about wiring my "center channel" center speaker to play both left and right(mono i guess) thanks

@AmulLuthra 7 лет назад

How to get that subwoofer signal. I mean I can get 4 rca signals from each of my speaker signals but please tell me how to get 6...Thanks

@AnthonyJ350 7 лет назад

You need a summing device like Audio Controls LC7i, or use the pre-out on your 4 channel to drive the mono block sub amp, or use a signal processor.

@StraightOuttaRockies 2 года назад

Hey Anthony, I'm using the same amp for just my subwoofer. I'm adding just a subwoofer to the stock stereo using line output convertor. For the RCA output coming out of line output convertor where will they go in the amp? I'm assuming on the right hand side where it says SUB Channel? And as I'm adding just the sub, will I be selecting 2 channel model for Input mode? Thank you!

@AnthonyJ350 2 года назад

How many channels is the amplifier?

@RacerXSOBE 9 лет назад

Final question, I will be running an extra pair of RCAs for the Future sub, should I leave them plugged into the amp even though there is no sub at this time, or will that weaken other signals?

@AnthonyJ350 9 лет назад

You can plug the RCA's in with no sub. I just wouldn't put the speaker leads in, until you have your sub ready to hook up.

@snickerkiller7 10 лет назад

Just a quick question that no one shows, Im going to in the future buy myself a mono block amp and i have a after market stereo. My question is when running the RCA wires from the amp to the head unit, what RCA plug ins do you plug the RCA cables from the amp into? I have 3 sets one for front, one for rear, and one for sub woofer. Do i plug the RCA wires from the amp into the Sub woofer RCA inputs?

@AnthonyJ350 10 лет назад

Nick Marolt If you're hooking your mono block amp to subs, hook the RCA's up to the subwoofer output on the back of the deck.

@snickerkiller7 10 лет назад

AnthonyJ350 Thank you so much, I couldn't find anyone who explained it in detail!

@enriquedelapezuela2206 9 лет назад

Anthony great video, question for you. I have Alpine HU w/ 6 RCA pre amp outputs, w/ stock tweeters in dash, Kicker Components in front doors and Kicker 6x9s in read deck. I am looking to add a 5 channel amp so I can get clear sound and also add a Sub later on. My question to you is, I believe Stock Dash Tweets are connected with door spkrs, where I connected the Components. When I install Amp will I have to separate comp from dash tweets, or just wire to comps and it should feed dash tweets?

@AnthonyJ350 9 лет назад

Typically the factory tweets have a capacitor wired in line so they don't play lower frequencies. If you're running the set up now off your Alpine, I see no problem amplifying them. Just when you set it up play it at low volume and monitor for distortion.

@NARINDERSINGH-mg6uk 6 лет назад

Can you guys show some tips for hooking 12” kicker es to 6 channel amp(Audison lrx 6.9)just sub no speakers they are hooked to my head unit Sony xplod .

@AnthonyJ350 3 года назад

Just follow the video or my other amplifier videos

@DR-um2bv 7 лет назад

on a 5 channel amp when it says 75w x4 & 300w x1 @ 4 ohms then 100w x4 & 600w x 1 @ 2 ohms. do you have to connect the 4 channel side on 2ohms in order to get 100w for the 4 channel side or is it all determined by how the 5th channel is configured 4 ohms or 2 ohms?

@TickleFingers 6 лет назад

D Rogers It's the impedance required by the speakers that dictates the draw on the amp. A 2 ohm speaker will pull a 2 ohm load from the amp, 4 ohm speaker will pull 4 ohms, and so on. Most car audio speakers are 4 ohms, but two 4 ohm speakers wired in parallel will yield a 2 ohm impedance. Those same two 4 ohm speakers wired in series will yield an 8 ohm impedance. A single voice coil sub at 4 ohms will pull 4 ohms, but a dual 4 ohm voice coil sub will yield 2 ohms or 8 ohms depending on wiring. If you put another 4 ohm voice coil sub in the mix you could wire 2 dual 4 ohm voice coil subs to be a 4 ohm final impedance. So, in summary, your speakers and your configuration dictates the load in the amp and is not something you can just select the amp to output. This is why amps will state that they are not stable at certain impedance and you should avoid configuring your speakers to draw a load the amplifier cannot properly handle. You'll experience potential adverse effects. There is also increased total harmonic distortion associated with lower impedance, but it does in most cases produce a higher overall power output. If you run a 2 ohm load on the sub channel and 4 ohm on the 4 channel, the amp will output according to the load for each channel. So in your scenario, the 4 channel would be running 75 watts at 4 ohms and 600 watts at 2 ohms on the sub. It is important to understand each piece of your system and select according to your desired end result. There is a lot to audio...... A LOT!

@AnthonyJ350 4 года назад

The output of the amp changes to depending on the load the speaker provides.

@johnnyp4466 3 года назад

what terminals do you use it you want to bridge the sub channel?

@AnthonyJ350 3 года назад

It's a mono output on the amplifier shown

@renedelafuente123 9 лет назад

Thanks for the video. In your opinion which amp is the best or close to it for sounding great and staying nice n cool at 5 or 6 channel level?

@AnthonyJ350 9 лет назад

Tony Garza Ahhhhhh so many choices! What kind of car do you have and what kind of music do you typically listen to and budget? Let's start with that.

@LiLViSsS 10 лет назад

Hey AnthonyJ350 I'm trying to save $150 and install myself, a 4ch and mono With the stinger wiring kit, is soldering on the terminals a necessity? And with the fuse holder at the beginning, will i need to do what you did with it? (i'm not sure what that was) Thanks a tonne

@AnthonyJ350 10 лет назад

It's a good idea to solder the terminals but technically you don't have to. If you're not too sure about doing the battery hook up I'd suggest asking a shop like mine to do that part for you (so the labour cost is a little less) and do the rest yourself.

@larrylawson6569 2 года назад

This doesn't address the empty Power Connector, Ground Connector, Remote Turn-On Connector, as well as the empty sockets for the output channels. Looking around I cannot find a kit/guide, etc for this. If I had known these would be bare empty sockets, I would have gone with another amp mfgr.

@AnthonyJ350 2 года назад

You can use ferrules. I talk about them here ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ca37WnL6Oxo.html

@AzzenGear 10 лет назад

Cool Vid! Hey AnthonyJ- I wanna run two 6 3/4 subs to my rear doors. I have a 5 channel amp and understand how to wire the front door components and the top rear coaxial and it would be simple to wire to a single sub but there's going to be two. How do I run the wire?

@AnthonyJ350 10 лет назад

stewnta How many voice coils does the sub have and at what load? You might want to watch my "how to wire subs in series or parallel" video.

@arulpeter 7 лет назад

Such a useful video now I know how not to make a video

@RichGarciaTv 7 лет назад

Arul Peter lol

@jeremythomas7792 6 лет назад

Lol

@AnthonyJ350 Год назад

Thanks for the feedback!

@carlosfrances01 9 лет назад

One question. Can i install 4 speakers and 1 subwoof to a 5 channel amp ? Somebody told me to run then with a separate amp . One for sub and one for speakers . Thanks

@AnthonyJ350 9 лет назад

***** The 5 channel is designed to run 4 speakers and a sub woofer. You could also run a 4 channel and a seperate mono block amp for the sub.

@carlosfrances01 9 лет назад

Thanks anthonyj350

@AnthonyJ350 9 лет назад

***** Make sure you also use good quality wire and the appropriate thickness.

@carlosfrances01 9 лет назад

AnthonyJ350 Thanks! Which cable you recomend for the 5 channel.amp and sub?

@AnthonyJ350 9 лет назад

***** I like all the Stinger Elite series wiring.

@vmsr1 9 лет назад

Nice 6:41 pure dark video ! ! ! :D

@alexv5585 9 лет назад

Hi Anthony can you make a video on how to wire a 4ch amp to a stock head unit and aftermarket speakers

@AnthonyJ350 9 лет назад

I'll try to get around to it when the right vehicle comes along my way.

@alexv5585 9 лет назад

Could you explain how I wanted to wire the stereo with lc7i processor

@godreacter288 9 лет назад

i was wondering how long hertz amps usally last becuse i had one for a year and it blew up

@AnthonyJ350 9 лет назад

+wyatt jones (godreacter) What model? How was it installed? Did it just stop working? What resistance load did you have on the amp?

@godreacter288 9 лет назад

+AnthonyJ350 it was a hcp 1d about 300w i believe and i opened it 2 diodes had caught fire

@godreacter288 9 лет назад

+wyatt jones (godreacter) 4 ohms and i belive i was fully loading it but im not sure

@ferewberehe7069 4 года назад

Night war bad!

@AnthonyJ350 4 года назад

Thanks for the feedback!

@jesussepulveda9426 6 лет назад

Have you ever hear about a flashlight the work great

@AnthonyJ350 6 лет назад

jesus Sepulveda Thanks for the suggestion!

@highspeed9518 5 лет назад

If you are running shielded quality rca cables and a jl amp you shouldn't have to worry about feedback

@AnthonyJ350 4 года назад

You never know, never hurts to go the extra mile.

@MrLabigdawg 8 лет назад

this video is to dark. I cant really see what going on.

@AnthonyJ350 4 года назад

Thanks for the feedback, we've made changes since the video.

@BrentW19 5 лет назад

you confused me with the cross over box...

@AnthonyJ350 5 лет назад

Refer to the instruction manual, speaker brands may be a bit different

@RobertoRodriguez-ce3iu 8 лет назад

Do you have any channel or page on Facebook ?

@AnthonyJ350 8 лет назад

Yup just search AnthonyJ350 on facebook or go to Www.gofasthavefun.ca

@LerRhann 7 лет назад

Video is too dark. Mic is too quiet. shouldn't put booties on before soldering. Did I miss anything?

@newbean96 9 лет назад

Whats a mili ?

@AnthonyJ350 9 лет назад

newbean96 It's the model of Hertz Audio speakers that were installed in the vehicle.

@thereal442 9 лет назад

newbean96 A song by lil wayne lol

@portmurphy1 5 лет назад

Can you bridge this amp for full power to 1 or 2 subs ❓

@AnthonyJ350 4 года назад

No, you can only adjust the load by wiring your subs in series or parallel.

@inorite4553 6 лет назад

I have a suggestion, Get yourself a shop light or spot light. I can't see shit.

@AnthonyJ350 6 лет назад

We did, this video was made 4 years ago.

@inorite4553 6 лет назад

......Ok.....ummmm...then get yourself a Delorean, go back in time and properly illuminate your video. :-) j/k

@blackman7249 6 лет назад

So basically what I need to do is turn off all light sources and let the leds from my equipment guide me. I see. The amps will light the way. I guess I’m the only one who gets this video. You don’t need to see to install.

@AnthonyJ350 6 лет назад

Black man Thanks for the feedback!

@AnthonyJ350 6 лет назад

Black man How about this video instead? Sorry at the time of that video I didn't have the funds to invest in more lighting.

@Van_frederick 9 лет назад

ahh, thats why i got engine noise, i ran all the wires together, 4 guage wire.

@AnthonyJ350 4 года назад

You can try running a long ground from the head unit and ground it with the amp. We run one with our rcas all the time now to avoid ground loops.

@emmanuelvega1270 10 лет назад

LOL if you get Tboned the last thing on your mind is wire running through your door.

@AnthonyJ350 10 лет назад

It's a fire hazard in that situation because if the wire get's pinched it could short and if the fuse doesn't blow or is installed incorrectly the wire will just light up.

@xbox360rocksful 10 лет назад

You need all that just to power up a JL audio 8" sub woofer, wow. I am sorry but you will low that damn sub with that power.

@AnthonyJ350 10 лет назад

How do you figure? That JL Audio sub handles 250 watts rms and that amp will only put out 300 watts rms at a 2 ohm load and 180 watts on a 4 ohm load. That's totally within spec of each other.

@ElJosuecito1 10 лет назад

Ur videos need more light.

@AnthonyJ350 10 лет назад

ElJosuecito1 Ya I know it's the next thing we have to buy for upgrading our gear.

@7046463 8 лет назад

if only there is enough light. :((

@victorlopez1114 5 лет назад

to dark need a flash light

@AnthonyJ350 4 года назад

Noted, we've made upgrades to our facilities and gear.

@desalineredux435 3 года назад

This has got to be the worst how to ever,

@AnthonyJ350 3 года назад

Thanks for the feedback!

@juanrojos78 3 года назад

It was horrible

@josearodriguez9601 3 года назад

The explanation is good... but the video sucks big time...is horrible.. but thanks for the time..

@AnthonyJ350 3 года назад

Thanks for watching!

@deadsypadilla 3 года назад

My headphones hit harder than your car. Gtfo

@AnthonyJ350 3 года назад

That's impossible and you know it. Do you even have a license? But I'll challenge you to that. Record the decibel level of your head phones, then I'll record this car.