5TH GEN 4RUNNER | Auxbeam 8 Gang Switch Panel Install

Подписаться 228

Просмотров 2,2 тыс.

50% 1

In this video, I give you guys a quick overview on how I installed and routed my wires for the Auxbeam 8 Gang switch panel. It was a very straightforward install and I love the clean look the switch panel provides when it comes to adding accessories to the 5th Gen 4Runner.
--- All Amazon affiliate links below help support the channel. --
4Runner Accessories (Some not featured in this video)
Diode Dynamics SS3 LED Fog Light Kit amzn.to/3rA13O9
LASFIT 9005 H11 LED Bulbs Combo 2022 amzn.to/48VNUjg
Auxbeam 8 Gang Switch Panel amzn.to/48H7ijR
RLB-HILON Cup Holder Insert amzn.to/3toCQL4
Center Console Organizer Tray and Divider amzn.to/45ofJ0C
Glove Box Organizer amzn.to/3ZOJUge
YITAMOTOR All-Weather Floor Mats amzn.to/48KboHJ
VIAIR 88P - 00088 Portable Compressor amzn.to/3Q9O7Ii
ARB ARB505 Deflator Kit amzn.to/3PUYuhQ
Camera Gear
4K Panasonic HC-VX981K Camcorder amzn.to/3YSei97
Backpack Camera Clip amzn.to/3qUVkC7
SD Card amzn.to/3YSROol
49mm 0.43x Wide Angle Lens amzn.to/46m6P4W

Развлечения

Опубликовано:

11 окт 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 25

@KenRupin 2 дня назад

I love your detail! Nicely done!

@richieewinns 3 месяца назад

Of all the videos, I actually found this one the simplest to understand. Every other video drags out and adds extra fluff, but this was straight to the point. Thanks!

@jarridgordon2155 3 месяца назад

Thank you. I try to give as clear of overview as I can because I know how hard it is to sift through all the tutorials on RU-vid to find that one snippet of info you need. Glad you enjoyed it.

@richieewinns 3 месяца назад

@@jarridgordon2155 absolutely, my only question is you mentioned you didn’t tap a fuse in the fusebox of the engine bay because of the protrusion and inability to seal the cover on again. Is that the real why you punched through the grommet to the interior for acc mode fuse instead?

@jarridgordon2155 3 месяца назад

@@richieewinns yes the accessory power fuse tap and the switch controller cable both ran through that grommet. Even if I figured out a way to tap into the engine bay fuse box I still would use that grommet for the for the switch panel control wire.

@ShhCaka 9 месяцев назад

Way to go Bucko!

@acet7 7 месяцев назад

Thank you very much for the video it's very informative. I just ordered the six button for my 2021 TRD OR, now I'm second-guessing myself saying that the eighth button fits fine as well.

@jarridgordon2155 7 месяцев назад

The 8 fits good. If I could go back I wish I did the RGB one just because I would like to be able to program the lights from my phone and make some of them have the strobe function. I think they also make an 8gang XL one, that one would probably be to big for the location I chose.

@acet7 7 месяцев назад

Yes I got the one that works with the cell phone.

@tylourdaubert6176 8 часов назад

Is there a reason you didnt tap into the acc fuse? Wouldnt that enable to use the lights with just 1 key press, and then still allow use while ignition/driving?

@jarridgordon2155 8 часов назад

@@tylourdaubert6176 with the fuse I tapped into I still can access the lights with 2 key presses even if the car is still off. I’m sure you can use the acc fuse but I pretty much never use the light unless I’m driving so this method works for me. With the fuse tap I have I can always experiment with different fuse locations so maybe down the road I can try the acc fuse.

@jakeaubrigreene1745 6 месяцев назад

How loose is your breaker and the switch controller on the fuse box. I just put mine in and while the smallest and medium screws work it’s not super firm which worries me when I take it off roading. Also how did you mount the switch in the cab without drilling? I’m assuming Velcro?

@jarridgordon2155 6 месяцев назад

Mine is all pretty tight on the fuse box. Taken it off roading and on washboards and have no issues. I made sure to drill a tiny pilot hole then screw in the screws using a screwdriver 🪛 not a drill because I wanted to make sure I didn’t strip out the plastic. For the switch panel on the dash you are correct I just used double sided 3M Velcro.

@lcatalla7292 8 месяцев назад

Did you reinstall the 10amp fuse to the tap fuse? Have encountered any problem since the install?

@jarridgordon2155 8 месяцев назад

Yes I installed a 10amp fuse into the fuse tap as well. So the fuse tap has 2 fuses. The orange/yellow one that came pre installed and the red 10amp one which I added. No issues at all so far.

@lcatalla7292 8 месяцев назад

@@jarridgordon2155 thank you!

@Treetopflyer777 5 месяцев назад

Was your red accessory wire long enough to go into the cab? Mine isn’t nearly long enough

@jarridgordon2155 5 месяцев назад

I didn’t add any extra wire. It just barely fit as you can see in the video. You just might not be able to rout it super clean. I just routed it for the shortest distance. The fuse tap does add a couple extra inches so that helped some.

@Treetopflyer777 5 месяцев назад

@@jarridgordon2155 thx. I might add some extra extra wire just to be safe. It looks like it might be 16 gauge. But to be honest, I don’t know the first thing about wiring. Lol The only thing I know for sure, is, if there’s wiring I will at some point shock myself or Short something out

@jarridgordon2155 4 месяца назад

Hahaha just disconnect the battery before doing anything and you will be good. 👍🏼 I agree I think it is 16 gauge. So you should be fine using extra 14 or 16 gauge wire.

@kiykim277 29 дней назад

Is there options to make them into strobe mode?

@jarridgordon2155 28 дней назад

Unfortunately not on the model I got. If you get the Bluetooth version that connects to the app on your phone, you would be able to set strobe patterns.

@kiykim277 28 дней назад

@@jarridgordon2155 Ah~. Thank you so much!