No video :(

7.3 Powerstroke Fuel System Upgrade: Sump & Pre Filter Install - NO MORE 1/4 Tank Issues!

Подписаться 3,8 тыс.

Просмотров 20 тыс.

50% 1

⬇ALL LINKS HERE⬇
R12H Fuel Filter: shorturl.at/puT37
1/4 Ball Valves: shorturl.at/bfCLQ
Thread Sealant: shorturl.at/chjrI
3/8 Barb Adapter: shorturl.at/iovQZ
1/2 Plug: shorturl.at/vwBRW
3/8 Fuel Line: shorturl.at/jyEGW
Tank Sump: shorturl.at/nBKY8
5/16 Pump Fitting: shorturl.at/agC37
Hose Clamps: shorturl.at/aetyD
--------------------------------------------------------------------------------------------
Like The Video 👍
Drop a Comment Below ⌨
Subscribe 😁 ► goo.gl/Kqzyk8
Thanks For Watching ❤

Опубликовано:

28 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 68

@downunderjuice 2 года назад

If only ever you tube video was like this. Straight to the point. Great information. Short and sweet. No giveaways, begging, click bait or ads.

@vaultexplorers1337 Год назад

Holy crap! I was thinking the same thing!

@GhidoraKidora Год назад

Fuck yeah

@kevinmurphy3464 8 месяцев назад

Nice video that was on point with no extra BS. Did mine with the Beans sump and dropped my tank to make sure the tank was clean and welded a small shield with a bolt on mount to protect it.

@PowerstrokeBoiz 8 месяцев назад

DM me pics on IG!

@levettehenson6606 Год назад

thanks for the info man. bout to do this mod. 200k and tanks never been dropped. truck has the famous don't go less than 1/4 syndrome lol

@PowerstrokeBoiz Год назад

It was killing me, didn’t have the money to spend on a FASS..so this DIY setup works, affordable and gets your hand working!

@michaelbenoit248 4 месяца назад

@@PowerstrokeBoiz, on my 1993 instead of doing the sump I used a section of fuel hose and a brass-T fitting to sit on the tank then have a pre-screen after it to catch before my pump. I still don’t go below 1/4 but I’ve done it in a pinch. You were smart on the ball valves I did the same on my pump when I need to clean the screen.

@kylewhitmccarthy2954 8 месяцев назад

Thanks for the vid.. about to do this to my 01 7.3L w/ 300K to prevent dropping the tank haha

@PowerstrokeBoiz 8 месяцев назад

4” hole vs. tank drop, HOLE SHE BLOWS! 🤣

@akquicksilver Месяц назад

Nice setup and a great install video. You need a finer micron rating than 10 for injector protection. 2 microns is pretty much industry standard. Are the o-rings viton?

@simpleman4224 Год назад

Has this system held up well for ya? I’m all about diy stuff! Thanks for sharing! 👍👍👍👍🇺🇸🇺🇸🇺🇸🇺🇸🙏🙏🙏🙏

@PowerstrokeBoiz Год назад

No problems or leaks. Just changed my filters months ago and my goodness it was worth the mod…

@mikeb6300 3 месяца назад

Nice Video of the installation and product, but FYI you shouldn’t use the pipe dope on any part of a fuel system, tape only reason being, is the it is not compatible to the fuel.

@PowerstrokeBoiz 3 месяца назад

I didn’t use “ pipe dope “. FYI you should look up PTFE is suitable for Fuel/Diesel 😇. Why I haven’t had one leak using it, even with twin fuel pumps now 😙

@darrentylor5473 2 месяца назад

So the whole purpose of this was to one, allow all the fuel in the tank to be used, and two, better filtration/seperation of water from the fuel. Bonus addition of drain out in case of bad fuel... Could that dual port sump be used to feed a China diesel heater?

@PowerstrokeBoiz 2 месяца назад

Yes it could!

@jackyzhou4874 2 года назад

Great product

@myown66 2 месяца назад

Thanks for the video. My question is about the return line, is it still going to the sending unit? did you plug the line coming out at the sending unit? where did you get the plugs?

@PowerstrokeBoiz 2 месяца назад

Plugged Feed, Using stock return.

@sheldonrafuse3837 Год назад

Did you remove the stock pickup from inside your tank? Great video by the way👌🙏🏻

@PowerstrokeBoiz Год назад

Stock pick up is still there. I just drilled a hole in the bottom like you watched

@logicmind240 8 месяцев назад

You also mentioned using 1/4 inch ball valves so we can change the filter on the water fuel separator but isn't that the wrong size? shouldn't it be 1/2 npt ball valves?

@PowerstrokeBoiz 8 месяцев назад

Whatever size I said. I said it loo

@logicmind240 Год назад

If you could recommend and piece together a fuel bowl delete or relocate kit for us, that would be amazing 👏 External pump , line extensions, wiring .... to go with this sump filter mod

@PowerstrokeBoiz Год назад

I’ve literally showed you step by step in this video how to do all of that. You just have to get your hands dirty lol

@logicmind240 Год назад

Do you think 10 microns is good enough to not damage/ clog the injectors? And how would you bypass the fuel bowl permanently as far as getting it out of the way for oil pump seal repairs/ services? Not sure what the 2 wire fuel bowl connector does...

@PowerstrokeBoiz Год назад

@@logicmind240 My fuel bowl is completely gone, you see in the video. 10 MICRONS is plenty fine

@logicmind240 Год назад

Keep looking for the fuel bowl and I don't even see you go to the motor one time in the video, are we talkin about the same fuel bowl sets on top of the valley on the 7.3 motor? I'm wanting to bypass, relocate or even remove that to gain excess to the hpop oil pump permanently

@PowerstrokeBoiz Год назад

@@logicmind240 I have a 6 AN Y ontop of the HPOP. it splits to both heads, excuse me

@tonywillingham8109 2 года назад

How can I protect the filter better when off roading? I worry about rocks kicking up and taking that thing out

@PowerstrokeBoiz 2 года назад

Simple! Just build a mini skid plate for it!

@kyleMcC13 7 месяцев назад

Thanks for the video, in the process of doing it right now! Did you use existing holes in the frame to mount the filter or drill your own?

@PowerstrokeBoiz 7 месяцев назад

I drilled one whole and used the other! :D

@kyleMcC13 7 месяцев назад

@@PowerstrokeBoiz Nice, thats what I ended up doing too. I made a little bracket but it seemed too flimsy so I drilled a hole and bolted to the frame. I hope nothing leaks!

@PowerstrokeBoiz 7 месяцев назад

@@kyleMcC13 Use JB Weld on every thread fitting, I love that stuff!

@zacharylehmann5890 7 месяцев назад

I just completed this exact instal and can’t get the fuel to the new fuel filter housing that was just added. Any tips or advice to look for?

@PowerstrokeBoiz 7 месяцев назад

Turn the key on to have pump run, open ball valves lol

@logicmind240 8 месяцев назад

What's your thoughts on adding a 6 microns filter after the fuel pump along the way to the fuel Y block?

@PowerstrokeBoiz 8 месяцев назад

Definitely add a POST Filter. I should have but never did, Or just move this one infront of the pump and it’s fixed.

@jonhammes6209 Год назад

I can't get the links to work

@chrisoberlin375 2 года назад

It’s been 3 months. How has this set up been working for you?

@PowerstrokeBoiz 2 года назад

No problems at all! Setup has been flawless!

@chrisoberlin375 2 года назад

@@PowerstrokeBoiz Sweet I think I am going to try this out. My 7.3 has 300k on it and has never had the tank dropped. I’m sure those screens in the tank are restricting some flow.

@PowerstrokeBoiz 2 года назад

@@chrisoberlin375 less than 100$ in parts. It’s definitely worth it. Plus you get further more out of a tank, at least I did

@logicmind240 8 месяцев назад

Will the plastic 3/8 hose fitting connector work on either side of the stock fuel pump? Part KP020

@PowerstrokeBoiz 8 месяцев назад

Yes it should.

@technicalitems731 Год назад

Will this work if I don’t have the sump adapter in tank? I did the HUTCH mod. Didn’t know if the gravity pressure of a sump helps the stock lift pump pull through a filter vs stock sending unit style. Thanks

@PowerstrokeBoiz Год назад

The effect of gravity DEFINITELY makes less strain on the fuel pump. No point in really doing this unless you go with a sump, whole idea was to be able to 100% utilize the absolute amount of fuel left in the bottom where the hutch mod can’t reach.

@Jackstrempel52 10 месяцев назад

Can I just install the filter with out a sump I want to get rid of the fuel bowl but I still want to have a filter but not in the engine bay

@PowerstrokeBoiz 10 месяцев назад

You can feed off stock feed lines yes! Just won’t get 100% empty tank

@technicalitems731 Год назад

Are the KP020 quick connect fitting designed for diesel or just air? I can see they work as fitment but are they holding up on the long run? Thanks for the video

@PowerstrokeBoiz Год назад

Their used all the time, even in my application for fuel! Look at user reviews on Amazon for pictures of people using it again in a fuel related application. I haven’t had one leak from them. Setups been working on my truck since this video was posted, and still going strong!