ADXL 345 Accelerometer FLSUN V400 Install Guide  

Got my ADXL today. Didn't work, but thanks to your video i changed the path and it calibrated beautifully. Thanks

Esta información vale millones, excelente video así deberían ser los videos de soporte de FLSUN

These videos you make for the V400 community are extremely valuable, please keep it up. Also, could you please address the criticism Zack Freedman made towards the V400 in his video "I I Reviewed the Stupidest Smart Devices From My Spam Folder" (at 20:17)? Like, how to fix them or what upgrades to get for the V400. I'm especially worried about the part where he says that the sock is glued to the nozzle. I also have no idea what upgrade parts to get for the parts he criticizes.

This will help me do the calibration for sure, but I apparently missed an important part of this. What software are you using on the PC? Thanks for the video.

Mhhhh, I read that the ADXL 345 has axes arrows (X,Y,Z) printed on the board, and they should match the axes of the 3D printer. Normally on a Core XY it is easy to mount, since the board should stay parallel to the plate, and the X and Y arrows on the IC boards should match the X and Y axes of the printer. You fixed the board with the screw in a way that the IC axes X/Y are diagonal/UP to the IC in the Z direction, and you will have incorrect calculations. I do not have seen anyone positioning the ADXL board on a delta in a different way than a CoreXY. May be I am wrong, but it would be better double check with some KLIPPER Delta expert on how to position the ADXL 345 on a delta. I ordered one, and I will check ho to install on my V400 as it will arrive.

Hello, where can I buy the ADXL345 with case and the cable can also be used with the original Flsun clipper

Hello, thank you for the tutorial. I am looking for a solution when I want to test the configuration of the y axis I receive this message each time at 82HZ. I use Fysetc USB 07:46 Internal error on command:'ADXL_AXE_Y' 07:46 Internal error on command:'SHAPER_CALIBRATE' 07:46 Klipper state: Shutdown So I have no problem with the X axis

Nice video Still overly complicated .I'll stick with my stock SR

My only issue with it is i wonder if the usb cord messes with the calibration

When I remove the hashtag my printer is stuck at the boot screen

Hola. Adquirí el ascelerómetro directamente de la marca y veo en su tutorial que no hacen ninguna modificación en la carpeta printer.cfg. ¿Son necesaria estas modificaciones? ¿El caso del video usa el mismo kit? Saludos

that's a bit ridiculous they didn't provide screws.

Hello. Could you please make a tutorial on how to add V400 to Prusaslicer? I have tried following instructions and profiles, but I get stuck. Prusaslicer does not show filaments at all, even after adding them. I know some people have managed to add V400 to Prusaslicer, but there is no guide out there.

I was curious as to why my V400 has an input shaping calibration option but no sensor was included..It says something along the lines of waiting for connection, I'm assuming its waiting for a sensor to be detected...I'm very new to the V400, Is there any way to "unlock" the speederpad in order to link one of my ender printers? I cant find the printers option and I'm assuming its because Flsun locks down the pad that's sent with the V400?

I copied and pasted the serial:/dev/serial/by-path/platform-5200000.ehci1-controller-usb-0:1.2:1.0 but it gives me klipper error....How can I go back to previous setup?

oggi mi è arrivato adxl345 ma pare che non funziona. Ho seguito alla lettera le configurazioni,ma quando si rimuove # la stampante non si collega più. Se rimetto # la stampante ritorna a collegarsi. Qualcuno ha idea cosa succede?

hi, i bought the FYSETC portable input shaper, it will work with the same procedre ? thans

I had no luck w PETG on the v400 this is an interesting fix I might give it it a try if I can find the device. Thanks for keeping your tutorial short and to the point as always.👍

Do I have to have the updated firmware to do this?

when i follow this video i get error once i remover the hash tag and restart,firmware will not restart,i followed this tutorial exactly

Is that for input shaping?