AMAZING DIY Pitts S12 Full Build and Flight 

STL Files: www.eclipson-a...
LW-PLA: colorfabb.com/...
Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me: www.buymeacoff...
See what else I am working on: / troymcmillan_rc
www.tiktok.com...
#3DPrinted,#RCAirplane, #ItFlies
Pitts S12 Parts:
SunnySky 2820 1100kv Motor: sunnyskyusa.co...
11x5.5 APC prop: amzn.to/3AFIA0V
60A ESC: amzn.to/3nwXJw1
ES08MA Servo: amzn.to/3ANk2mB
3S 2700mAh Battery:
4S 2200mAh Battery:
2x8mm Screws: amzn.to/3p8gmqY
10x5x3 Magnets: amzn.to/3bzb4Pz
1/8” Wheel Collar: amzn.to/3p4tvl1
3pin wire assortment: amzn.to/3l1xNYt
XT60 connector: amzn.to/3iyZWnf
2mm push rod ends: amzn.to/3nnjD4U
3D Printers I use and recommend:
AnyCubic Vyper: amzn.to/3AJqwTM
Artillery Sidewinder 3D Printer: amzn.to/396eqIp
Artillery Genius 3D Printer: amzn.to/39cA6CZ
Ender3 V2: amzn.to/2SmLOGk
Twotrees Sapphire-PRO: amzn.to/3wtNOLz
Anycubic Mega X Printer: amzn.to/3f4oS89
Fokoos Odin-5: amzn.to/3fAES06
3D Printing Filament:
ABS for motor mounts: amzn.to/3xgLI2c
ColorFabb LW-PLA: colorfabb.com/...
ePLA-ST: amzn.to/3AGymgY
TPU: amzn.to/2Sw3Oe8
Tools and Supplies used:
Spektrum DX6 Controller: amzn.to/3l6NFsD
Spektrum NX10 Controller: amzn.to/3jnjvST
Receiver: amzn.to/3j4PbK4
Battery Charger: amzn.to/3vejwfL
Charge cable: amzn.to/34lOk3q
XT60 connector: amzn.to/3iyZWnf
Assortment of 3-Pin Extension Cables: amzn.to/3l1xNYt
Z-Bend pliers: amzn.to/34mA0rt
2mm push rod ends: amzn.to/3nnjD4U
CA Glue: amzn.to/2J8EvNW
CA Accelerator: amzn.to/3fpbycz
Low-Voltage Tester: amzn.to/2Yk0A0w
Hot knife: amzn.to/3nrCwUH
Drill Bits: amzn.to/3nIJzrx
Hobby Knife: amzn.to/3eYOYJq
#11 blades: amzn.to/3vTJZ2W
Z-Bend pliers: amzn.to/34mA0rt
Build Mat: amzn.to/3vJmauw
Onboard Camera: amzn.to/3rp2OrH
Lead weight: amzn.to/3cFnzeu
Print Settings:
Quality:
Layer Height - 0.25
Initial Layer Height - 0.15
Line Width - 0.4
Walls:
Wall Line Count - 1
Z Seam Alignment - User Specified
Z Seam Position - Back (Position part to align Z seam)
Seam Corner Preference - Expose Seam
Top/Bottom:
Top Layers - 0
Bottom Layers - 0
Infill:
Infill Density - 0
Material:
Printing Temperature - 235
Build Plate Temperature - 60
Flow - 55%
Speed:
Print Speed - 100
Outer Wall Speed - 55
Inner Wall Speed - 55
Travel Speed - 120
Travel:
Enable Retraction - Checked
Retraction Distance - 7.5mm (Bowden Tube Ender3)
Retraction Speed - 35mm/s
Retraction Extra Prime Amount - 0.2
Combing Mode - off
Cooling:
Enable Print Cooling - Checked
Fan Speed - 80
Mesh Fixes:
Union Overlapping Volumes - Checked
Special Modes:
Surface Mode - Normal
Experimental:
Slicing Tolerance - Middle
Music:
Song: Jarico - Landscape (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: • Video
Music: Joakim Karud:
RU-vid: / joakimkarud
Soundcloud: / joakimkarud
Music provided by Argofox:
From The Dust - Solar
• From The Dust - Solar ...
Music provided by Argofox:
Ghost'n'Ghost - Lighthouse
• Ghost'n'Ghost - Lighth...
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!