Anti Drop Sensors are not Rusty But still deebot giving error ?? Check the Wires 

Thanks for all the support! I have found your videos super helpful. I am still getting anti-drop sensors/errors. I have tested the sensors with iPhone camera and I can see that the sensors are working. I checked the bumper sensors, I checked the wires, there is no rust signs, I have cleaned out with an air duster but still have issues. The plastic bumper was scratched so I polished it and removed all scratches. The robot in some areas drives into things and the bumper doesn’t stop the robot. It tries to drive over it even if it’s a chair leg or wall. It doesn’t happen everywhere, particularly under the couch on a light grey rug.

bought a brand new ozmo 950 at auction as a damaged one. after replacing the battery, it reported an error with the anti-drop sensors. The sensors were ok... I replaced the motherboard from my old Ozmo and everything works fine.

Thank you for your Help!!! U R great!

Hello, I am from India and have a Yeedi which has no service network here. I find your videos great and have opened my device looking at your videos. My robot keeps giving antidrop sensor warning though nothing seems wrong with sensor. My application is a flat apartment floor, so can I just short the IR LED receivers at the connector end and will it work? Will appreciate a response. Is there an email ID I can contact you on? Thanks in advance

Hello, I have a Deebot T8 with the error message "check dropsensor". I have already swapped the right and left sensors. the message still came. I have now noticed that the left sensors and the left front sensor are not working. using IR check. From the middle on, one side of the sensors doesn't work. The cables in the front look good and there is nothing rusty. Do you have an idea what it could be - or can I send it to you? ;) Best regards, thank you for your videos!

Hello, I'm Pablo from Uruguay, first of all I'm very grateful for the videos you make, they have helped me a lot to be able to fix my ecobacs, I have an ecovacs t5, which I had to change the motherboard because it wouldn't charge the battery. The problem is that when I changed the motherboard, the vacuum cleaner made 7 dings. and I can't link it to the app. Do you know how to load firmware from a PC to my vacuum cleaner?

I just opened my T8+ today and all wire and anti drop sensor is good and not rusted. However the ‘clean anti drop sensor” problem still occur when in the middle of cleaning, normally it clean for couple minutes and it stop and said error. Any ideas?

Thanks for the videos. I have a deebot x1 plus and this is the 2nd one that experiences the same issue. My vaccum sounded louder than usual when it was stuck and might have overheated. Ever since its stuck in low suction mode and can not change suction power. Can you please let me know what i should replace to resolve the issue ? Thanks from Canada

Where can we get original accessories for Deebot U2 pro in Pune Maharashtra... Bought from Amazon but quality is local.

Hi new subscriber here.Very good channel . I have a DEEBOT t20 omni. It keeps telling me the bumper is stuck , I’ve checked/ cleaned it and it still doesn’t work. Will you ever be making a video of a full maintenance/ breakdown on a T20. Btw. My T20 is 7 months old. Cheers in advance for your help.

Thank you for sharing your experience. I have ozmo 950 and gives drop sensor error; ı checked the sensors , no rusty and no dust. But when I checked with mobile camera, sensors no infrared lights. What do you think about the reason? Main board?

Hi.. can u help me with the Deebot problem. My deebot is working ,But only issue is now i cannot use the custom mapping, only auto mode is working in mobile app. For Custom it showing data times out error.

moss developed in my deboot n8 reservoir. how to remove it. please suggest

Hello! I have a Dreamebot L10S Pro robot vacuum cleaner. The water spray does not work while mopping. The technical service in Turkey does not provide feedback and is inadequate. Is there a technical document, video or a program that can guide me so that I can solve this problem with my own means? I have electronic knowledge. I am happy with the device, but this chronic malfunction annoys me. I'm waiting for your help.

Can i just contact the wires together and cancel the sensor ?? because i do not neet it . I habe flat flour and no any drop place 😢😢😢😢

I have same error from my Deboot N8 Pro. I ordered left and right sensor from aliexpress but now I am thinking that I had the same wiring problem.

Ecovacs launch in india this year 2024 how to get authorised service holder in india can u tell me

Hi sir, i am having yeedi vac 2, it is saying please clean anti drop sensors, please help me in this regards

Hi sir,my robo is working towards but not working suction part.

Hi sir can you tell your mobile member and your shop location

This is happend once in every year 😂… got tired already

Yeah you mention nearly everything , making moves like a snake , giving false smile but do not tell about main reason smd resisitors on pcb need checking 33 ohm, 10 ohm near sensor plug ...

Thank you for the clear explanation and information. My problem is a little bit complicated, We need your help. When we turn on de deebot it then gives 7 beeps and then nothing. Reseting also doesn't work. Drop sensors looks clean. The deebot is just 1 month out of warranty. My husband wants to try to repair it himself. We already opened it up following your instructions. See here the problem ru-vid.comPFIgpRfOOyU?si=A5CU4zjdaxrb5aH3 I hope you can help us!