Thanks for the info, I replaced my battery but now the device started saying to power on the device before charging, (it is powered on). I have tried a second charger and as stated a new battery but still nothing, I am currently looking at the fuses but they look good, do you have any idea? Thanks in advance.
Plz check the battery voltage first....is it according to the mentioned in previous battery...?? If Only shows 8 to 9 v Only then possibly battery fault...if shows 14+ v then motherboard issue
Hello,How can I contact you to find out if you can send me some anti-drop sensors for the Yeedi DVX34? I need 6, 2 at the front and 2 on each side. I live in Sherbrooke, Quebec, Canada.Thank you.
Hello,How can I contact you to find out if you can send me some anti-drop sensors for the Yeedi DVX34? I need 6, 2 at the front and 2 on each side. I live in Sherbrooke, Quebec, Canada.Thank you.
Hello,How can I contact you to find out if you can send me some anti-drop sensors for the Yeedi DVX34? I need 6, 2 at the front and 2 on each side. I live in Sherbrooke, Quebec, Canada.Thank you.
Thank you for the excellent video. With your support I've been able to open my 950 and am awaiting a new motherboard from AliExpress. I have one question that I hope you can assist with. After disassembly and inverting the Debot, I found two small rubber grommets on the table that I can't identify. They did not come up in any of the videos that I watched. This is a link to a jpg showing the grommets: drive.google.com/file/d/1-1zCT_ST-zLy8KiYasDS3LBxFduUPHq8/view?usp=drive_link I hope you can help me figure out where they belong. Thank you again for your all your assistance! 👍👍
Bro, my T9 has high pitch sound and doesn't vacuum/ sucks dust like before. Basically it has attitude problem. Can a main brush motor be the problem? Or is it a mother bot issue? Been using it for 4 years and now this problem occurs. Please help. Hey, ur videos are very informative.
I am planning to buy ECOVACS omni t20 can anyone suggest who are already using it, how it works and it’s durability, any flaws and issues with it… is it worthy for that price… please reply and suggest me to buy or not… please, that really helps me
How often should we change the complete accessories like side brushes main brushes , filters and mop… and what will be the cost for whole set ? Should we change for every 3 to 6 months…. Can you please advise, please reply to my comment
My Ecovac Debot Ozmo 950 displays gives out an error message saying "please help me out" when turned on. It remains stuck on the "starting to clean" stage but doesn't actually begin cleaning. After a few minutes, it shows this error message. What could be the issue?
I have a Ozmo 920 series and the vacuum reports: 'my laser distance sensor is blocked please clean it' I have taken the laser motor assembly apart and have thououghly cleaned it with compressed air (although it was not particulalry fouled) Could the laser module itself have failed? If so, can I buy a replacement module? Many thanks
Hello, After a electical oscilation due rain, My deebot x1 omni stoped working the right side brush (purple). I already replaced the engine(motor) but the problem remain. Could you suporte me which the next step? Replace any other parts or any other reset or software upload?
I have purchased deboot N10 recently... Bt its not mopping properly and am not getting it resolved bt the ecovas technician also....its leaving a gap in btwn while moppings ... I can see yhe lines on floor while mopping... Please can u guide me in this
Hi, I have gone through all your upload I am unable to find one for my deebot x1 issue, my main brush is spinning non stop even when it’s at the charging station, can you please help me regarding this matter . I would truly appreciate your response. Thank you once again sir.
Can you please help me, my omni deebot x1 used to be working fine however now the main brush keep spinning non stop even at it’s charging port. Can I know how can I fix it please .
Hi! I replaced both the side brush motors thanks to your video, and now they work, but I get this error: The d-tof sensor stopped working. What could I have done wrong?
Hello, I recently reset my map and attempted to remap my 950. Unfortunately, the dock is no longer being detected by the device. It does not charge or recognize the dock's presence. I used a multimeter to measure the dock's output and found that it was less than 0.5A at approximately 20V. I am concerned that the low amperage may be the cause of the issue, or it could potentially be a motherboard problem. I would greatly appreciate any insights or suggestions you may have to resolve this matter. Thank you for your attention to this issue.
When I turn it off and put it on the doc it makes the starting sound and then turns off and then repeats. It still has about 50% battery and had no battery issue so far.
My brush is the OG and still not spinning but I can't find a video of yours or anyone else's on how to take apart my U2 to see if it's the brush motor isn't spinning
Bonjour. Sur mon Ecovac debout T9, c'est ma serpillère qui ne fonctionne pas. je l'ai changé et c'est toujours pareil. Donc, ça doit provenir de l'intérieur. Pouvez vous m'aiguiller où chercher svp. Merci.
How many cents did you guys save by going with plastic drive gears? Because it wasn’t worth it. Ours is shot after only 3 years. Sounds like a dentist drill as the gearbox is stripped out.
Also I have found the sensor on Amazon but it only says n8 module compatible and mine I think is the N10 like in the vid will this matter coz I cannot find a one with N10 in description