AWD 2X2 MINI BIKE PROJECT TEST DRIVE 

@Mike festiva, thanks! Learning from you😉

@Douglas Martin, thanks! I appreciate your interest in my project!

@btwenzel05, thanks!🙂 I agree with you, I need a guard for that tensioner!

@Big Dan, its coming, there will be snow & mud test drives!

@Austin Hamilton, thank alot for subscribing, I really appreciate that!🙂

@Richard Fiqueroa, thanks!🙂

@fatbuddycat, thanks! 2x2 with suspension sounds really good 👍I need to think about it 🤔

Run those atv tires at 3.5 psi and you have suspension. ;)

I appreciate you subscribing, thanks alot bud!🙂

@Dave Underwood, thanks alot for good words! I will definitely look into that, thanks for the advice!🙂

Even rubber wheels would be better. Steel tensioners are very noisy and tranmit alot of vibration to the frame for some reason.

@tnatcher1, I see what you're saying 😀 it climbs hills pretty good, I have a video coming that will show its capabilities of hill climbing, stay tuned, thanks for watching!

@Dennis Hein, thanks!🙂

@John Wheels thanks bud!

@Bryan s, that's an idea👍but as far as I know they are hard to find, and they are not that reliable, they have some issues to

@Sycothrash666 thanks!

@Dan Kornfield, thanks bud!🙂 I don't know yet, maybe, I'll let you know if I decide to build some kits

I would imagine it would be difficult to mass produce

@Manitoba Man thanks alot!

@Mark Merritt, you are right, you have to sacrifice something to gain something else

@Trash to transportations, thanks!

@Marty Lawson, thanks for the advice! You are right about that chain tensioner, you don't really need it, but my thought was that it will tension the chain as the chain wears and stretches, and also prevent chain from bouncing

@buildurtruckurway, Thanks bud! That was a speed up video🙂, real speed was approximately 35 mph

@ BWX thanks! You are right, applying brakes to one wheel stops the other one through the chain. Thanks for the advice about the brake shoes, you probably heard my brakes making noise

@@OkayBuilds Yup mine made the same noise. 😆

@BWX i gotta swap mine😀

@J K, no, there is no overrun clutch, but surprisingly it turns pretty good even on hard pavement, but I will be adding a front drive disconnect..

@@OkayBuilds yeah all you need is to let the front wheel overrun the rear during turning to prevent drive line binding.

@J K, thanks for the advice👍, I appreciate that!

@@2000freefuel Where could one find the info on doing that overrun on the front wheel?

@mlindsay527 thanks! Ok ok😉

@valleytractorservices9310, California

Yes, I can give you list, no problem! 1. Square tubing I used: 3/4x3/4, 2"x1" 2. Sprockets: Wheel sprockets are 60t from Amazon, all the other sprockets are 13t, except the one that comes right after the cvt that one is 20t. 3. Tires are 20x7x8, rims stock Coleman ct200u. 4. Pillow block Bearings 3/4, flange bearings 3/4 (Amazon) 5. U joint - steering shaft from 2011 Kia Sportage. I think I covered the main parts I used. Most of the stuff I had laying around, but you can find all of this stuff with no problem( Amazon, go power sports, bmi go carts, etc), let me if you have any questions!

@Manuel Perez thanks! I will try to find some sand out here to test it, stay tuned, there is more videos coming with this 2x2 mini bike

@@OkayBuilds awesome love the mods you made with the 2wd lots of fun thanks for great video

drop the tire pressure as low as you can and I'm sure it will do great in loose sand!

@Manuel Perez, thanks again bud!

@Marty Iawson, thanks for the advice, I will definitely try that!

@Xavier Arizmendez, I used idle sprocket from go power sports, piece of square tubing and two sets of nuts and bolts

@Progress, it will be hard without my 2x2 mini bike... but you will be the first one I will let know if I decide to sell it 😉

@Young__Money, thanks! Let's race😀