This video will demonstrate the proper procedure for repairing Briggs & Stratton recoil starters for models 90000, 10A900, 10C900, 120000 with plastic pawls. The basic techniques in this video can also be used to repair other starters.
The assembly of the lawn mower could be done without any problems ru-vid.comUgkxTPN04aT-Qdjr_KS3ql7ng8wnU3wwsCqk also recommend I just puzzled something about the red strange “key”. However, it quickly turned out that this creates a kind of contact bridge between battery packs and lawn mowers. An additional backup as a father of a 1 year old nephew is great!! :-)
My pull starter just quit working so I ordered the pulley with spring, pawl friction plate assembly and rope. I watched this video then disassembled mine. The spring was the problem as I suspected. I hadn't thought too much about how to wind up the spring until I received the new parts. There is no notch on the outside of the pulley to engage the rope for winding it like the old styles have. In 78 - 79 I worked at a lawnmower shop and learned a lot, but a lot has changed the way things are made. The new pull starter system is actually easier to wind. A welders vise grip will make this job easier to hold the pulley from turning while installing the rope or something similar. Just clamp the steel housing between the pulley webing. This will prevent the pulley from turning I'm going to feed a skinny screwdriver through the housing and out the hole in the pulley, then attach a needle nose vise grip onto the screwdriver to hold the pulley so I can install the rope because I don't have a welders vise grip. I personally will allow the pulley to have atleast one revolution left after the rope has extended to guarantee the spring won't get damaged if wound too tight because the spring bottomed out before the rope extended all the way out. I was taught, you only need to wind it 6 - 8 times, but it also depends on how log the rope is. Great video! 👍🧓
Looked at a few videos. This is the same model starter I have. No special tools. No nailing it to a board and using a drill + zip ties :s So simple. That’s the way I’ll be doing it. Cheers mate.
Definitely the best of the videos on this subject. Only improvement I had to make was getting the rope through the eyelets - really tough to line it up and get it through, so I straightened out a paper clip and inserted it into the end of the rope to stiffen it up so I could push it through easily. Thank you for great instruction!
People like you make save people like me a ton of money.. but was a bit apprehensive going in with the spring winding and other steps. It couldn’t have been easier. Thank You!
EXCELLENT!!! Much better than the other three I just watched. You showed how to resolve more problems AND how to test operation before reassembly. Thanks
I haven’t tried this yet because I have to go buy a retainer kit, but thank you for this video you showed me why my recoil wasn’t catching and how to fix my problem!!!
MOTO: Wow ! x10 ! Great Video ! Looks just like my B&S Troy TF 220 with a broken rope.. The information on the loop in the inside of the recoil spring was my issue, not broken, the hook in the case was so dirty I didn't even know it was there. Followed your directions and got it on the third try. THANK YOU, THANK YOU ! Richard "The Happy" ------------------------------
Thanks for including the torque spec of the friction plate bolt - is the only place I've found it. I think I messed mine up over torqeing before I found this video so have ordered new parts. I didn't even notice the music so many have complained about - sheesh! Guess I was laser focused on your explanation!
I have watched a few videos on this subject and have to admit, it's probably one of the better ones. The video should and this one does, deal with differ scenarios: 1) How to install a new pulley and spring 2) What if one of the spring hooks snap 3) What if the cord breaks 4) What if the pawls need replacing 5)Some times the pawl needle guides snap off 5) The pawls retaining disc nut, how much torque needed to tighten I feel you have covered most of the above scenarios. Thanks. There is one more topic that can be covered and that is how to replace the whole cord pull unit as this requires drilling the rivets holding the new unit to the casing. I have seen a different video ion this subject. OK the music used is not to my taste but then we all like different music. What is important is the volume should be low and distracting. 🙏
Thanks! I should have watched the video before I drilled out the rivets holding the recoil assembly to the cover but glad I watched it after-the-fact which enabled me to be able to replace the pull-cord and successfully re-assemble all of the bits and pieces.
Thank you for the video, I wish I watched this first before trying to fix it without prior knowledge. Just a quick FYI, IF you do turn the pulley clockwise it will damage the spring, however it's a very simple fix. You just have to bend the spring back into shape again. Ask me how I know this lol. This tutorial also applies for the 499901 pulley.
Thanks to this video I was able to fix my starter and I just finished mowing the loan. I am so grateful for that vid. WOW. I thought I would have to get my mower to the service.
Great video. The spring popped out when I was replacing the starter pull rope so this had exactly the steps I needed to put everything back together. Thanks!
Thanks for the video. I would have never figured this out by myself. My OEM Briggs and Stratton spring came with the inside hook bent the opposite way. Not sure why, but I did buy the OEM spring that was specified by my manual. Once I bent the hook around the other way (hook bent counter clockwise) then it all went well. I hope I did not weaken the metal. This video saved me a lot of headache and time.
I don,t comment much unless it's really good, it's really good! Thanks exactly what I needed, I was just about to take it to a small engine repair shop.
Very detailed. Nice job. Sometimes inserting the rope through the eyelet hole isn't easy due to fraying of cord end. Heating the frayed end momentarily with a lighter and then pinching the melted frays together and allowing the end to cool makes it easier to thread into the hole.
Ugh, didn't think to look up a video till I lost pieces I didn't know I lost till I watched this video. This is an incredible video "Thank you for making it"
Thanks for the great how to video. You explained everything so it all made sense to me and demonstrated how to solve the problem I was trying to fix. It was a simple and speedy repair. Replacing a broken starter rope and the spring had come out too. The part about aligning the top cap for the pawls was a great tip. Parts were only about $5. Thanks again.
Very well composed and detailed thanks 👍🏻one suggestion about burning the rope you could use clear tape to make it narrow to assist threading it in same way shoe lace has stiffened end
Thank you very much. I recently broke the pull rope on my yard machines tiller. While replacing the rope, the spring popped out, and I couldn't figure how to get it back in, lol.
Thank you! I have a half inch cut on my right knuckle but I always do that whenever I attempt an engine project. Your instructions were spot on. I had to drill out the entrance way into the plastic ring as the rope was too thick to pass through. Other than that and a few cuss words it went back and the mower is running!! 👍🏻
Good video. it did tell me that my spring is bad (the spring popped out after disassembly and would not sit straight in the pulley). Not worth $60 for the assembly on a mower I bought used 10 years ago but at least I feel good knowing I gave it a shot.
I didn't read any of the other comments, but I did notice the 44 thumbs down... How disappointing. I think the people that gave the thumbs down just completely have no mechanical ability whatsoever. I watch this video, I work on lawn mowers frequently, and still learn new things. :-) great job on this video A+
Very informative video. The only thing I did different is use a small screw driver to hold the pulley in place while installing the rope instead of my fingers.
Good video the only thing I would recommend is a clamp to hold the pully in place while you insert the rope and maybe lubricate the end of the rope going into the pully that was the only part that gave me problems no matter how well I had it lined up
Good, helpful video! Should the parts be cleaned then oiled/greased at all before reinstalling? Also, people doing this work should be warned to wear goggle-type eye protection.