Clutch for Longtail Mud Motors. Mud Skipper Retriever Clutch Review

Подписаться 42 тыс.

Просмотров 48 тыс.

50% 1

Clutch for Longtail Mud Motors. Mud Skipper Retriever Clutch Review
In this video we will be testing and reviewing the Mud Skipper Retriever Clutch Longtail Mud Motor on a Tracker Topper 1436. Follow along as we test it in the muddy river, and our own version of torture testing on this mud motor clutch. Let's see if the retriever clutch for longtails can hold up to Send It abuse. And as always don't forget to stick around to the end of the video for the bloopers and the hater's corner!
Buy Send It Jon Boats Shirts, Hoodies, Hats, Decals here:
thejonyacht.com/collections/s...
Check out great deals and discounts from our channel sponsors:
5% off promo code for Tiny Boat Nation Outdoors, for all your boat building materials and accessories.
Visit www.tbnation.net
Use promo code: FULLSENDUNICORN
10% off promo code for Freedom Lube, The most American oil you can buy!
Visit www.freddomlineproducts.com
Use promo code: ATF10
Link to One Hit Wonder Paint:
www.ohwpaint.com/discount/ATF...
Get 5$ off your OHW order use code: ATFHYDRO
My Other Channel: TB Nation Outdoors RU-vid Channel:
/ @tbnationoutdoors
Camera gear we use:
Camera Lenses: amzn.to/36rcdE4
Camera Mount: amzn.to/2GqMroQ
Flex Mount: amzn.to/2tIDLHY
Flex Tripod: amzn.to/2ux7CTB
Tall Tripod: amzn.to/36xUgUF
Lav Mic: amzn.to/2t27awm
Products used in the boat repair video series:
Kreg Rip-Cut saw attachment: amzn.to/35PHhxq
Jigsaw blades: amzn.to/2DCjLb4
Straight cut router bit: amzn.to/2ODUMut
Wood glue: amzn.to/2R7DxTN
Wood clamps: amzn.to/2Y6aW2C
Fiberglass resin: amzn.to/2qbD5Jl
Chip brush: amzn.to/380rbTN
10X20 Canopy Cover: amzn.to/2Gzyqsq
Standard Rivet Gun: amzn.to/32afGFW
Large Rivet Gun: amzn.to/33rFeyj
¼ Inch Sealed Rivets: amzn.to/2MBQTEb
3m 5200 Sealant: amzn.to/2McyOgP
JB Marine Weld: amzn.to/2B91iC0
Brazing rods: amzn.to/2nGoa8A
Brazing Flux: amzn.to/2OGsgZz
3/16 Inch Sealed Rivets: amzn.to/2zEFoJE
Rivets: amzn.to/2PJwccl
Welder: amzn.to/2C7OLiv
Welding helmet: amzn.to/2WLNY0k
Welding gloves: amzn.to/2PIMRgo
Angle Grinder: amzn.to/2qglTC0
Flap Disc: amzn.to/2qmaMY4
Float Pods: www.explorebeavertail.com/pro...
22 Inch Light Bar: amzn.to/37zNboI
11 Inch Light Bar: amzn.to/2N2wiJS
LED Navigation Lights: amzn.to/30HJv2J
3/16 Inch Sealed Rivets: amzn.to/2zEFoJE
Grab Bar: www.beaverdammudrunners.com/p...
Marine Grade Duplex Wire: tbnation.net/collections/elec...
Trolling Motor Circuit Breaker: tbnation.net/collections/elec...
Heat Shrink Ring Terminals: tbnation.net/collections/elec...
Fuse Panel: tbnation.net/collections/elec...
Battery Disconnect: tbnation.net/products/bep-eas...
Switch Panel: amzn.to/3IaMqUn
Watch the entire Project Bottomland Bateau Series:
• Project Bottomland Bateau

Опубликовано:

19 окт 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 101

@1153mf Год назад

If you have a lot of parts left over that just means you are more efficient than the engineers who designed it!

@SendItJonBoats Год назад

LMAO, you sir are a genius! LOL

@caswellsubs 10 месяцев назад

Actually, what this means is that MSkip assumed that Mr Simmons had the common sense to either figure it out, or ask MSkip for advise before posting this nonsense. Over 1000 units running without ONE incidence what is portrayed here makes this appear to be a blatant bias.

@1153mf Год назад

I work as a scuba dive and recently while in a zero vis river I felt something that felt like a prop, and a long shaft. I got pumped because I knew what I just touched. It was a 27 hp go devil on a sunken boat. Dove down with some tools took it off the boat and tossed it in mine….after 4 hernias. I just took the dude completely apart and rebuilt it and got it running. I just am waiting for a u joint to come in and on my boat she goes!

@SendItJonBoats Год назад

Dude that is awesome you found a go devil. I would have done the same thing. I hope you get it running, those things are awesome.

@noturfather1106 Месяц назад

I wouldve wanted the boat too

@secondgrowthhomes Месяц назад

Sweet!!!!

@robsteve7043 6 месяцев назад

Just found your channel. I love your videos and your humor.

@tobaccovalleyoutdoors Год назад

I added the clutch to my twister kit from mudskipper and am happy with it so far. Where I hunt it’s pretty tight so I think the twister/clutch combo really helps with getting in and about.

@SendItJonBoats Год назад

That's a good point, I didn't think about hunting up the trees and stumps getting in there tight. Picking up decoys having that low idle would help a lot too.

@NastyNate-fn6od Год назад

Finally!!!!! I’ve been waiting for the video for months lol, glad you finally had some time to get R done scooter !!!!

@SendItJonBoats Год назад

Yee Yee. Im back at it again finally. Got some cool stuff coming and lots of videos planned.

@NastyNate-fn6od Год назад

@@SendItJonBoats how’s the diy Harley mud motor build going ?

@nathanbillingsley42 Год назад

I'm already excited!!

@SendItJonBoats Год назад

Thanks Nathan, should be a good video. Got a new drone so we made some really cool shots.

@SugarRiverOutdoors Год назад

Awesome video that's the first I've ever saw the clutch on a long tail. As for the aluminum props, they do their job. They wear out and take the brunt of the abuse. If I don't hit a log or a stump with it to break it I wear them out in the gravel and the sand they are cheap and only take two minutes to replace.

@UltraMagaFan Год назад

This is actually pretty neat. The longtail I get I'm going to have to install a clutch on. The lake that I boat in is absolutely full of stumps.

@SendItJonBoats Год назад

You will probably like it then, it is a cool little gizmo.

@ianbartelmez4720 Год назад

I think it's a nifty thing, great for setting and picking up decoys, my buddy has a beavertail 40 surface drive and the momentary switch is pretty great, I may try one out.

@SendItJonBoats Год назад

That's a great point, it would be really handy for picking up decoys.

@daleley7645 Год назад

Don't know what to think of the clutch thing. Thanks for taking time for a video.

@SendItJonBoats Год назад

I think its cool, not necessarily needed but still cool.

@jonjacobjingleheimerschmid3798 Год назад

Thanks for the video! I like the clutch on my surface drive so well I was going to build on a clutch for long tail.... But now with your info it'd be much better just to buy one...I always wondered why nobody offered a clutch. Oh...I like to run limb lines so there's frequent stops... $185. Delivered

@SendItJonBoats Год назад

Limb lines would be a real good reason to run the clutch! It would help a lot. Thanks for watching the video.

@carolyntracytalbott5865 Год назад

Cool video, what is the clutch for and does it come with a boat plug? If I need a clutch I'm probably somewhere I should be or doing something I shouldn't be doing , and I hope I remember to put the plug in. I like your videos and was wondering if you could do one on boat plugs and how to use them.

@azlongtales Год назад

Added to our clutch playlist. We have installed three of them so far and all them engaged at 2k rpm wonder why yours was engaging so low? Good job on the torture test wondered how long it would last completely locked up. Good to know it can handle without destroying itself.

@SendItJonBoats Год назад

Awesome! Thanks for watching.

@dougdavis777 Год назад

Awesome your great keep it going

@SendItJonBoats Год назад

Thank you. Glad you enjoyed the video.

@trtony-xe4cl 3 месяца назад

It would be a sad & lonely life without the scooters out there,we wouldn't have any brainless Di!!! to laugh at.just found your channel & subscribed,,keep the corny coming

@mikenorby9470 7 месяцев назад

The hater corner sold me bro subscred

@user-ok2vl1yo5s 7 месяцев назад

As a thought you might try to pull that thin shim out of the clutch housing, I think your end play tolerance is to tight an its putting pressure on the clutch drum

@colemccrary5922 Год назад

i've watched just about all of your videos and can't recall if you've taken the governor out of any of your mud motors. I've got a 13hp predator on a welded 1436 and would like to get a little more speed than 15-16mph. I've tried 3 different pro sizes with hardly any change. Any tips?

@SendItJonBoats Год назад

I have a video taking the governor out of a 670, but I have not filmed on for a 420 or any of the smaller motors. Planning on it, just havent done it yet. 16-20 is a common top speed range for a 1436, I know because I just did speed testing on this boat. My suggestion would be to get a better carb (Mikuni 34mm seems to be popular), air filter, better flowing exhaust, lash the valves, zip tie on the governor spring, and get a lot of time on the water moving the longtail around until you get it running the way you want. keep going down in prop size until you achieve your desired speed, but 16-20 is the range you are going to be shooting for in a welded hull because of the extra weight.

@klutch545 Год назад

Great video! Just used my first mud motor today! I think I’ll buy a clutch kit, because I was definitely surprised at the speed at idle (12ft v-hull). Ideally, a very low speed or no movement at all would benefit me and where I launch/take-out. Also, my Predator 224 (the newer 6.5hp) cuts out when going from 3/4 or full throttle to idle. Could be I just need to break-in the motor, but I’ll probably mess with the idle screw and governor arm. Any suggestions are much appreciated!

@SendItJonBoats Год назад

I have not messed with the 224 yet, I would assume like any other Chinese knock off motor the carbs usually suck! I used to mess with them a little bit but now I just rip them off and get an aftermarket carb. I am going to try some of the cheap amazon carbs soon and see if any are worth a crap.

@dereksmith2929 11 месяцев назад

I know I’m late to the party and you probably have it figured out, but thought I’d offer some input. I experienced the same thing with my 670. Different animal, so it might not be applicable to your setup. I have to run an electric fuel pump if I want to run WOT. The stock pulse pump just can’t keep up, especially now that the motor is no longer stock and I’m running a Mikuni 34mm carb. On the smaller predator’s, I’m assuming the fuel is gravity fed, so it might be worth looking into some sort of external pump. On your application, an electric pump might be too much, so a pulse pump may work.

@stevemedlock5716 4 месяца назад

awesome

@genekind8752 Год назад

Thanks for the video! You just saved me a couple hundred dollars. I like the concept of a clutch on a mud motor but they need to work on the final product. My "Hillbilly Super Boat" couldn't get the RPMs low enough to disengage the clutch. It would literally be a 5" engine extension on my rig.

@caswellsubs 10 месяцев назад

Perhaps Mr Simmons should have contacted Mud-skipper before posting this?

@genekind8752 10 месяцев назад

@@caswellsubs Why? They contacted him and sent the product for review. He reviewed it and there ya go.

@awaybee5516 2 месяца назад

Do they work on the twisters mud motor

@arronjohnston742 Год назад

that clutch is a cloned max torque so you should be able to play with different springs to adjust when it engages, one "hack" you can do is cut the stock spring, cut a coil bend the next down so you can hook it back into a ring an see how much slack it has you want it kinda snug, cutting more coils will slightly adjust engagment, so it engages at higher rpm but you can also get "perfomance" springs too just don't go to heavy of springs with a stock motor ......... ole red beard garage has video on it ............ anyway great to see you back on 👍

@SendItJonBoats Год назад

Thanks very much for the info. I have never messed with a clutch before. I may try cutting the springs down and seeing how that goes. Appreciate you watching and giving me some guidance. I was so lost installing this thing.

@arronjohnston742 Год назад

@@SendItJonBoats no problem Sir. they're pretty simple, every few runs you might wanna strip the clutch an lube it as it only runs on a bushing it's pretty simple just a few drops oil an she's all good again.......... here's red beards video from max torque (i'm a visual learner so seeing it helps 🙂 ) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-gr6xQGnjYT8.html

@CaptPeterson Год назад

Get it bro.

@SendItJonBoats Год назад

LOL Thanks bud!

@kipmyers5897 Год назад

Would you tell us again the color code on the paint on the Jon boat in this video? I'm working on painting mine and I like the color you chose on this one...Do you have gator glide on the bottom? I was curious if they have a dark color to match the paint you used...As always great video !! Thanks

@SendItJonBoats Год назад

There is no color code, this is all spray paint. It will be shown how I did it in the next video.

@kipmyers5897 Год назад

@@SendItJonBoats Ok thanks ..I'll Check out the next video on...I doubt I'll get to paint it anytime soon with with cold weather coming on here in KY ..Do you have any suggestions as to where to learn about prop size and pitch? Here is my problem ...I put a 65 hp Merc on a Jon boat..Ive never had it the water....the motor and prop combo came off a heavier shi boat ...I'm guessing the set up won't be much faster on my Jon boat even with it being might lighter .I think it will carry weight well but my thinking is the prop is like a rearends gear in a car ...in other words at a certain rpm that's as fast as it can go..So on a lighter boat it should mean it could take a prop that covers more area per rpm ....How can I Guage what pitch I have now? Is more pitch and bigger prop mean it pushes the boat forward more on each revolution? I know this is alot of confusing questions I hope you can help me with ...I don't see this subject talked about much on the boat channels....Just as long as I don't hear my question in the scooter comments lol....ok?

@kipmyers5897 Год назад

The question I ask you about props......I found a video on prop size and pitch ....I thought I would let you know that I had ansewered my own question so I sent this so you wouldn't have to waste time to answer my question...Thanks

@prettywildoutdoors3725 Год назад

Can you do a video with some of the mudskipper surface drives?

@SendItJonBoats Год назад

Yeah when I can afford to buy one. I tried getting them to send me one for review, they were not interested.

@prettywildoutdoors3725 Год назад

@@SendItJonBoats I’ve been thinking about getting one to replace my outboard they’re a little expensive so I wanted to see a review from somebody who knew what they were doing first

@hammer9856 Год назад

"Since the bolts are metric you'll need a metric crescent wrench" LMAO 🤣🤣🤣🤣🤣🤣🤣I'd watch your vids just for your one liners.

@SendItJonBoats Год назад

Gotta watch out for them metric bolts, need to have the correct metric monkey wrench lol! Thanks for watching

@jimgreenhoe1609 Год назад

That is just a metric adjustable hammer..

@backwoodshomestead Год назад

Great video! I am a dealer for mud skipper in Canada. I am ordering a couple of these clutches for 7hp and 16hp this week. Glad to see they fit other kits but I'm pretty sure they are supposed to stop 100 percent. @AZLONGTAILs has a video of this clutch and it stops fully. I wonder why your doesn't fully stop fully? keep up the good work bud!

@caswellsubs 10 месяцев назад

You wonder why it doesn't stop? Operator error perhaps? Over 1000 sold and and no one else has the problem.

@caswellsubs 10 месяцев назад

Likely it's a little oil or grease on the pads. it should wear off.

@oneoldjimmy1 Год назад

Do you notice and clutch knocking on yours? Mine sounds like a rod knock. Gonna have to pull it back apart, and shim it off the pto side more

@oneoldjimmy1 2 месяца назад

I ended up rebuilding my retriever clutch with a real Max-torque clutch and its holding up much better. And it doesn't care about all the extra power

@waddell7354 Год назад

A new video? Well butter my butt, call me a biscuit, dig out the white lightin' and smack my grandma on the mouth! We sendin' it today boys!!!!!

@SendItJonBoats Год назад

LMAO! Yes sir I am back at it finally!

@6MABBOTT Год назад

Whats the smallest engine you would use on a long tail mud motor build Have a 6hp pressure washer that the pump went but motor is still strong. Is this worth the effort?

@jonjacobjingleheimerschmid3798 Год назад

Harbor freight 6 hp moters are now about $130.... I have 3 mud moters,surface drive is a six ...long and short tail are 6.5.. All work well on a 12'' Jon boats

@SendItJonBoats Год назад

the little 6.5 hp from harbor freight is the smallest one I have ever run and it works good on small boat. It did work on my big boat but it was not very fast.

@markbaker4927 20 дней назад

Maybe you need to add another shim because the clutch is too tight . Also , probably useless to my style , but I would love to see a reverse on a short tail mud motor that I can afford. The long tail just won’t turn in some spots and you have to pole backward

@bmoutdoors4831 Год назад

Hey Chris. I know this isn’t probably the best place to ask this but since i’m here, why not? I’m getting a 35HP GTR in a few weeks for my 16’ 48” War Eagle. I was wanting to know if you could paint match the GTR to my war eagle. You could make a video on painting it if you wanted. I live relatively close to you and could bring it by if you can fit me in. Thanks in advance.

@SendItJonBoats Год назад

I wish I could but I am currently closed on painting and hydro dipping for a while. Having to move and opening the boat shop has been a nightmare.

@bmoutdoors4831 Год назад

@@SendItJonBoats Jeez man take your time, I live in Madison, GA about 10-15 min west of lake oconee. I’m wanting to get it painted by you because you do the best work (that i’ve seen) in my area.

@chucksmith5002 Год назад

I wished you had GPS it without the Clutch and GPS it with the Clutch to see if any slippage at all.

@SendItJonBoats Год назад

I did, I was filming a separate speed test video at the same time. Speeds were no different than without the clutch. New video on that will be coming soon.